110649 Kenmore Dryer - Instructions

All Instructions for the 110649
121 - 135 of 2765

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Poorly designed lint filter/ gasket falls off
25 of 34 people found this instruction helpful.
  • John from Madison, WI
  • Really Easy
  • Less than 15 mins
Replaced
Was this helpful?
Thank you for voting!
too long to dry
21 of 22 people found this instruction helpful.
  • Victor from San Antonio, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, then connect the two wires into new element, and put the element back in place, and put the back cover, now it getting really hot, and save me a lot of time and money on energy too.
Was this helpful?
Thank you for voting!
Needed to change rear exhaust to the side to fit dryer into my closet.
44 of 91 people found this instruction helpful.
  • Mark from San Diego, CA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.
Was this helpful?
Thank you for voting!
Dryer runs with no heat
23 of 29 people found this instruction helpful.
  • Paul from Bradford, MA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
It was easier to remove the blower manifold cover, (3 screws) to get at the heater element. Remove the heat shield, disconnect the two wires from the element. There is another screw on the side holding the element in the housing. Remove it and slide the element torward you. I used pliers as it was a snug fit. Replace. Good time to vacuum the whole area.
Was this helpful?
Thank you for voting!
Dryer Would not start
23 of 29 people found this instruction helpful.
  • Heath from YORK, PA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
Repair was easy after identifying the problem. Parts select was correct with the 3 parts for trouble shooting. However I should have looked at the door switch 1st. Ordered a thermostat and On switch 1st. Then had to reorder the door switch. In the future just order all 3 to avoid the shipping charges and return what you don't need to save time and money.
Was this helpful?
Thank you for voting!
No heat, everything else worked fine.
22 of 26 people found this instruction helpful.
  • STEVEN from MORA, MN
  • Easy
  • Less than 15 mins
  • Nutdriver
Installed the new High Limit Thermostat onto the new Heating element and installed the unit on the dryer. Wires were then connected and the dryer was tested. Repair complete. Dryer is 25 years old and this is its first repair.
Was this helpful?
Thank you for voting!
Push start and the motor would hum.
22 of 26 people found this instruction helpful.
  • Doug from Manitowoc, WI
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
**** Remove power cord from the wall****

As said earlier, you will need to lift the top. Drop the two screws holding the lint shoot and pop the top by sliding a screw driver into the corner on the front. Lif tthe top and rest against the wall behid the unit. remove the two (4 total) screws at the top and bottom of the front doo r assembly.
Place sometin under the front portion of the drum. At this point you'll see the need to clean everything! :) Slide the belt off and around the drum, (take note of the routing it takes.) Remove the drum by gently pulling it towards you. Set it aside. Clean more. :) (It is nice to have a vacuum handy.) At this point you really need to get to the rear of the system. So I tipped the top back down, and spun it around. Removed the rear panel and cleaned some more. (15 years of a lot of lint in there!) Then you'll need to remove the rear cover on the left side, covering the blower impeller. Get read for a whole lot of debris. Vacuum again. So now you have the motor exposed in the front and rear. You need to remove the impeller by turning that clockwise to loosen it. The trick is holding the shaft in place from the front at the same time. I used an old rag and wedged it into the impeller edges and worked it around until it jamed up. Once the rag was wedged pretty good, I went back to the front spun the shaft. Then you can remove the impeller by hand. Vacuum more. You may get by without having to remove the lint shoot completely, but I did just to clean it up more. I did have to remove two screws in the upper corner near the top of the lint shoot. (Basically the hold the back in place.) I took a few notes at this point about the wiring harness. Used a heavier screw driver (standard), You can push down on the clips that hold the old motor in place. Then work it out the front. Clean more. The new motor is not an exact replacement slightly differnt but the instructions with it were ok. Follow them for the correct wiring. You will need to remove one wire and cut and recrimp a spade lug or two. I used ty-wraps to secure the lines back in place. Look closely at the diagrams and make sure you set the motor down in the same direction the instructions say, if you twist it slightly it will sorta lock in place where it needs to be. Re-install the hold down clips to the front and rear of the motor. Clean up your impeller, and reinstall it too. Then basically reassemble the dryer...tracing your steps backwards. This isn't really difficult, it just takes time and as you can see, you will/should clean as you go !
Was this helpful?
Thank you for voting!
No heat
27 of 42 people found this instruction helpful.
  • Jaime from Chantilly, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Everything seems to work on the electric/gas dryer, but would not generate any heat. Did some research and ordered the thermal fuse & thermostat based on that. Replacement was simple and went well, however it did not fix the issue. Should have checked the continuity first as I found the "replaced parts" to be good. Have checked all ot her possible symptoms except the heating element, which requires addition labor. Overall, partselect portion was as advertised. All parts arrived quickly and were priced fair.
Was this helpful?
Thank you for voting!
Dryer working but drum light not working, bulb ok.
22 of 27 people found this instruction helpful.
  • Denton from Indianapolis, IN
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Problem: Drum light not working, bulb ok. Removed 6 screws on panel behind timer, light, buzzer, switches. Lifted back of dryer top then moved dryer top forward and off of dryer. The switch was located above the door. Unhooked wiring plug and took out 2 screws holding in the switch. Installed new switch and repaced bulb. Reassembled as ne eded and tested light by opening door. Works great.
Was this helpful?
Thank you for voting!
Drum would turn but not heat.
20 of 22 people found this instruction helpful.
  • james from corpus christi, TX
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
After tearing the back off by removing the numerous 1/4 inch hex screws, and locating the schematic in the compartment behind the dryer controls, I took a multimeter on the resistance setting and tested all the components I deduced were part of the heating circuit until i found the upper limit temp fuse of was open (i.e infinite , OL, ho w ever your meter will display this). I ordered the kit from here and upon installation found I had a different type of Thermistat assembly then the kit came with, however, the kit did anticipate this might happen and had "some" instruction on modifying the wire harness to accommodate the part. Essentially if you have this older style you will need to do some basic wire stripping and crimping to make it all work. While I am an electrical technician on aircraft, anyone should be able to follow the how-to video on this page(which deals exactly with what I had) and with the proper tools install this part.
I also cleaned out and inspected the rest of the dryer since I had it all open, including looking for burning on the heating element and inspection of the rest of the wiring harness. Finally removed the lint chute by removing the two screws located under the lint basket door, and the nuts holding it to the dryer frame and did a work over on it, finding a lot of compacted lint and debris inside. A can of compressed air helped a lot for this.
Was this helpful?
Thank you for voting!
The Dryer Would Not Turn On
19 of 19 people found this instruction helpful.
  • Ribhe from Wildwood, MO
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
The dryer wouldn’t turn on at all. It was like it was unplugged from the wall. However, fixing it couldn't be easier. I simply removed the back panel, found the fuse, tested it with an Ohmmeter (to determine that this was the part that didn't work), ordered the part from this website, and replaced the part. The part arrived in about t wo days. The shipping was a little pricey, but overall the whole thing cost me $20 vs. whatever it would cost me to get someone else to repair it. The website helps to identify the problem, and it is helpful to read how other people fixed their problems. It was so easy and the service was so good, I will definitely use this website again and recommend it to others.
Was this helpful?
Thank you for voting!
Idler Pulley broke
21 of 26 people found this instruction helpful.
  • Keith from Richmond, VA
  • Really Easy
  • 15 - 30 mins
  • Socket set
I disconnect the power, then the vent pipe. I removed the back panel of the dryer to access the pulley and removed the belt. Replaced the back and put everything back together.
Was this helpful?
Thank you for voting!
Noisy sound from dryer
20 of 23 people found this instruction helpful.
  • john from OLYMPIA, WA
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
Just like video except there were two screws in back to take control head off. Be prepared to have shop vacation ready. Clean dryer duct too. Have bandaids ready. Plastic triangles are not easy to take off, video makes it look easy.
Was this helpful?
Thank you for voting!
Replaced belt while I was in there replacing motor
20 of 24 people found this instruction helpful.
  • Douglas from COMMERCE, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
If you were to do the Belt Replacement only, here is the quick synopsis:
1. Unplug dryer;
2a. Open lint door on top of dryer and remove the two phillips head screws that hold the lint bay to the metal dryer top;
2b. Next remove the two brakets holding the metal top to the dryer back (one screw on each bracket);
3. Use a flat-blade screw driver to pry off the top of the dryer (leaving the timer and start button area attached);
4. Lift off top and push back to expose just enough area so you can get to the two screws holding the dryer sides to the dryer front;
5. Unplug door switch;
6. Unscrew screws from #4;
7. With door open, lift dryer front (only about an inch) and then pry bottom of dryer front from dryer sides. The bottom of the dryer front is not screwed, just siting on Front Panel Clips;
8. Once the front is off the dryer, simply remove the belt and install the new one. Please note that while you are in here, you may want to inspect the rear drum seal and replace if it is worn to the point where metal is rubbing on metal. This is also a good time to clean out dust from inside this cavity to help extend the life of the bearings on the rollers and prevent dust from accumulating and gunking up the motor, etc.
9. Re-assemble tin the opposite order.
If you have any mechanical sense at all and you don't know anything about dryers, you will be surprised at the simplicity of the dryer.
Was this helpful?
Thank you for voting!
Moisture sensors need replacement
20 of 24 people found this instruction helpful.
  • Jack from JONESBORO, AR
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Inside the dryer tub, remove the filter housing by removing two phillips head screws. Unplug the sensor wires, note when replacing wires, black wire goes on upper sensor.
Separate filter grill from housing. Using the pliers, compress the tabs on the sensor plugs and push it thru the grill. The small blade screwdriver may come in h andy here to pry up on sensor to assist in pulling the plug end through the grill. Replace the sensors by hooking short end into grill and pushing the long end through the grill. When replacing the housing to the dryer, the most difficult thing is getting the screwdriver onto the recessed screws. Be sure to put the tab on top of the housing under the dryer frame when rotating the assembly into place.
Was this helpful?
Thank you for voting!
All Instructions for the 110649
121 - 135 of 2765