1106301 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
very loud squeeling sound
110 of 120 people
found this instruction helpful.
-
jason from HOLDEN, MA
- Really Easy
- 30 - 60 mins
-
Socket set
The issue was the idler pulley. First I began opening up the front panel based on a youtube video but soon realized the model was slightly different and required a lot more items to remove. I saw the pulley in the back with nothing in the way so I put the front panel crap back on and removed the rear panel. There it was, very simple to re
... Read more
move and replace. I'm not looking forward to drum rollers though. Hopefully they're aren't as difficult as they appear.
Read less
Was this helpful?
Thank you for voting!
Broke start switch while moving
109 of 118 people
found this instruction helpful.
-
Dennis from Port Orchard, WA
- Easy
- 15 - 30 mins
-
Screw drivers
Turned off the power.Pulled the dryer out, removed the screws from the control cover panel, unplugged the switch, pressed the release clip the did the opposite to install new switch. Replaced the back panel, put the nob on and it looks as good as new.Turned on the power.
Was this helpful?
Thank you for voting!
dryer door would not stay shut
103 of 107 people
found this instruction helpful.
-
Pam from Woodbridge, VA
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
This repair was a cinch. Pliers to pull out the metal piece and a screwdriver to pry out the 'catch' part in the door. Both replacement pieces went right in. I cannot believe how easy and CHEAP this fix was, and I'm so glad I found this site!! I figured I would have to call a repairman and pay big bucks, so I put it off, but the door
... Read more
was getting worse--slamming it so hard to keep it shut. Again, thanks for this great site.
Read less
Was this helpful?
Thank you for voting!
Squeaky Dryer Noise
94 of 106 people
found this instruction helpful.
-
Eddie from PELZER, SC
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
I purchased the dryer repair kit with the drum belt, wheels and idler pulley. I watched the instructional videos online and it seemed fairly straight forward. Breaking down the dryer and replacing the pulleys was easy enough. My problem began when I tried to feed the drum belt around the idler pulley. After finishing the job, the dryer wo
... Read more
uld not turn and the sensor light stayed on. I thought something else was broken with the dryer and spent hours trouble shooting other problems that I was having. Finally I figured out that the drum belt was not installed correctly around the idler pulley. However, I could not get it properly installed from the front of the machine so I tried from the rear still with no avail. I finally had to fish the old belt out of the garbage can that I had thrown away earlier. I lined up the old belt with the new one in the kit and discovered that the new belt was much smaller, so I put the old one back on the drum. Here's the lesson I learned...make sure the belts are the same size before attempting to install. The old idler was responsible for the squeaking and that stopped but I am still using the same old drum belt. Hope it lasts.
Read less
Was this helpful?
Thank you for voting!
door switch actuator spring broken
92 of 100 people
found this instruction helpful.
-
Paul from Vero Beach, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
-unplugged appliance
-removed lint trap
-removed 2 lint trap shute screws with phillips screwdriver
-popped open top of appliance with standard screwdriver by applying pressure at each front corner so that it could be tilted up to access actuator switch on right side of door
-removed 2 actuator switch screws, located o ... Read more n upper right side of laundry door, with phillips screwdriver (screws are accessed from outside of door frame not through appliance top).
-discarded broken actuator spring (accessed from open appliance top)
-replaced new actuator spring
-replaced 2 actuator switch screws
-closed top
-replaced 2 lint trap shute screws
-replaced lint trap
-plugged in appliance
-tested for operation
-kissed by happy wife
-removed lint trap
-removed 2 lint trap shute screws with phillips screwdriver
-popped open top of appliance with standard screwdriver by applying pressure at each front corner so that it could be tilted up to access actuator switch on right side of door
-removed 2 actuator switch screws, located o ... Read more n upper right side of laundry door, with phillips screwdriver (screws are accessed from outside of door frame not through appliance top).
-discarded broken actuator spring (accessed from open appliance top)
-replaced new actuator spring
-replaced 2 actuator switch screws
-closed top
-replaced 2 lint trap shute screws
-replaced lint trap
-plugged in appliance
-tested for operation
-kissed by happy wife
Read less
Was this helpful?
Thank you for voting!
dryer wouldn't dry
110 of 191 people
found this instruction helpful.
-
JEFFERY from ABINGDON, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
un pluged it then removed the hose took the back off took out the 2 screws out of each part replace it with the new parts , then pluged it back to make sure it would work and it did the very first time. i'm 1 happy roper owner.
Other Parts Used:
Was this helpful?
Thank you for voting!
Very Loud Squeaking Noise
79 of 100 people
found this instruction helpful.
-
GREGORY from Wilsonville, OR
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
1) Disconnected power cord from wall. 2) Disconnected vent hose from back of dryer. 3)Removed dryer rear panel. 4)Disengaged tension spring on idle wheel arm. 5) Removed worn idle wheel. 6)Installed new Idler wheel assembly. 7) Vacuumed dust from rear of dryer (optional, recommended). 8) Reinstalled rear cover, vent hose and power cord. E
... Read more
asy repair 15-30
Read less
Was this helpful?
Thank you for voting!
Door switch did absolutely nothing....dryer kept running
98 of 166 people
found this instruction helpful.
-
Clark from Melbourne, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I read a fix-it article from another contributor and followed those instructions to the T. Pull out lint trap, remove the two screws. Slide the top cover towards the front and prop it up with a mop handle.
Unscrew two screws in the door switch (with the door open) - Oh, to keep from killing yourself unplug the dryer just in case. ... Read more Take pliers and pull the plug apart. It will be right in front of you in the right corner at the top. Plug new switch into that plug, reinstall the switch by reinstalling the two screws you removed. Snap top back into place and reinstall the two screws at the lint trap. Oh, don't forget to clean the trap and slide it back into the unit. Now you have earned that beer.
Put tools away and proudly show your job off to the wife telling her how difficult it was.
Unscrew two screws in the door switch (with the door open) - Oh, to keep from killing yourself unplug the dryer just in case. ... Read more Take pliers and pull the plug apart. It will be right in front of you in the right corner at the top. Plug new switch into that plug, reinstall the switch by reinstalling the two screws you removed. Snap top back into place and reinstall the two screws at the lint trap. Oh, don't forget to clean the trap and slide it back into the unit. Now you have earned that beer.
Put tools away and proudly show your job off to the wife telling her how difficult it was.
Read less
Was this helpful?
Thank you for voting!
Door won't latch
95 of 158 people
found this instruction helpful.
-
Jill from bellevue, WA
- Really Easy
- Less than 15 mins
-
Pliers
I did NOT have to repair the latch on the actual door, just the small metal piece that it hooks on (on the dryer itself) and it took about 10 seconds to.....do it myself. Just used needle nose pliers so squeeze the piece together and fit it in. thanks
Was this helpful?
Thank you for voting!
broken belt
66 of 78 people
found this instruction helpful.
-
Larry from exeter, RI
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
First I removed back and top of dryer, then the support braces holding the drum, after that I took the drum out and the blower covers and cleaned the whole dryer of lint and other debris. Installed the new belt and then reassembled the dryer.
Was this helpful?
Thank you for voting!
Broken Switch Assembly
90 of 153 people
found this instruction helpful.
-
Michael from Dearborn, MI
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
This was my first dryer repair, and it was so easy. Simply pull out the lint trap and unscrew the two screws that are exposed. They attach the top deck of the dryer to the drum.
Once it's unscrewed, pull forward while lifting the top of the dryer. The top is attached to the control assembly. They should both lift up, but ... Read more you'll need something to prop it up like you would the hood of your car.
Next, use the pliers to pinch the connector so that you can separate the two parts of the connector.
Open the dryer door to gain access to the screws that hold the switch in place. Use your screwdriver to unscrew the switch.
Plug the new switch connector in, and close up the dryer.
Word of caution; there are sharp edges inside the dryer so be careful.
Once it's unscrewed, pull forward while lifting the top of the dryer. The top is attached to the control assembly. They should both lift up, but ... Read more you'll need something to prop it up like you would the hood of your car.
Next, use the pliers to pinch the connector so that you can separate the two parts of the connector.
Open the dryer door to gain access to the screws that hold the switch in place. Use your screwdriver to unscrew the switch.
Plug the new switch connector in, and close up the dryer.
Word of caution; there are sharp edges inside the dryer so be careful.
Read less
Was this helpful?
Thank you for voting!
Felt gasket on lint filter loose...
61 of 71 people
found this instruction helpful.
-
Catherine from Atascadero, CA
- Really Easy
- Less than 15 mins
Found this site by googling, and it works! I searched lint filters and just ordered based on how it looked...LOL! Husband wasn't home, it looked pretty much like the one I had in my hand, so.... I ordered it. It is the perfect fit and seems to have a tighter gasket glued in all around the screen. Let's hope this one lasts longer than 6 mo
... Read more
nths! Thank you Parts Select for being so fast!! Filter got here in less than 48 hrs.!
Read less
Was this helpful?
Thank you for voting!
Rear tub seal failure
67 of 90 people
found this instruction helpful.
-
Jerry from Everett, WA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the
... Read more
unit...works fine
Read less
Was this helpful?
Thank you for voting!
No Heat When Drying
60 of 70 people
found this instruction helpful.
-
DAVID from CHARLOTTE, NC
- Easy
- 30 - 60 mins
-
Nutdriver
I followed the tips from the repair video. Easy as 1-2-3. I changed both the heating element as well as the thermal cut off. Went ahead and repaired the door catch. Brand new dryer for the next 10 years. I do advise to pull out your shop vac and remove the tons of lint that accumulates in the bottom. A definite fire hazardous. I
... Read more
do attest that this web site is the best by far.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
door kept coming open dryer shuts off
95 of 176 people
found this instruction helpful.
-
RONALD from SALMON, ID
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
use screwdriver topry plastic out plyers to pull out metal latch put new parts in
Was this helpful?
Thank you for voting!