110629 Kenmore Dryer - Instructions

All Instructions for the 110629
61 - 75 of 1335

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer turns off after 1-2 minutes
23 of 27 people found this instruction helpful.
  • Dixon from Santa Fe, NM
  • Easy
  • 30 - 60 mins
  • Nutdriver
I tried to follow directions followed by others on this site after diagnosing the problem via suggestions provided by users. I have a Whirlpool Duet dryer from 2002. We've had problems since moving about 3 years ago. I removed the front panel (lower) by unscrewing the two bottom screws (1/4" sheet metal screws). Then I took out the lint s creen and the metal tube/contraption immediately beneath to get access to the area where thermistor is located. See the drawing/chart to help you locate this. It's really easier than it seems. Make sure you have the chart/drawing for your model - it makes difference! The thermistor came out pretty easily with a nutdriver that has a swivel offset shaft. Ask your hardware store tool dept. about that one. Put everything back in reverse order of course and test either with/without the front panel re-attached. In my case it fixed at least part of the problem. I was able to get clothes almost dry with most settings but I have yet to install the moisture sensor to see if that helps in addition to the internal-bias thermistor. I am the kind of person that does one thing at a time so at least I now know the thermistor was bad. Good luck and hang in there with your own repair. It's a lot cheaper even if it takes you longer to do than a pro.
Was this helpful?
Thank you for voting!
Needed to change rear exhaust to the side to fit dryer into my closet.
44 of 91 people found this instruction helpful.
  • Mark from San Diego, CA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.
Was this helpful?
Thank you for voting!
Poorly designed lint filter/ gasket falls off
25 of 34 people found this instruction helpful.
  • John from Madison, WI
  • Really Easy
  • Less than 15 mins
Replaced
Was this helpful?
Thank you for voting!
Dryer runs with no heat
23 of 29 people found this instruction helpful.
  • Paul from Bradford, MA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
It was easier to remove the blower manifold cover, (3 screws) to get at the heater element. Remove the heat shield, disconnect the two wires from the element. There is another screw on the side holding the element in the housing. Remove it and slide the element torward you. I used pliers as it was a snug fit. Replace. Good time to vacuum the whole area.
Was this helpful?
Thank you for voting!
Dryer Would not start
23 of 29 people found this instruction helpful.
  • Heath from YORK, PA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
Repair was easy after identifying the problem. Parts select was correct with the 3 parts for trouble shooting. However I should have looked at the door switch 1st. Ordered a thermostat and On switch 1st. Then had to reorder the door switch. In the future just order all 3 to avoid the shipping charges and return what you don't need to save time and money.
Was this helpful?
Thank you for voting!
Dryer working but drum light not working, bulb ok.
22 of 27 people found this instruction helpful.
  • Denton from Indianapolis, IN
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Problem: Drum light not working, bulb ok. Removed 6 screws on panel behind timer, light, buzzer, switches. Lifted back of dryer top then moved dryer top forward and off of dryer. The switch was located above the door. Unhooked wiring plug and took out 2 screws holding in the switch. Installed new switch and repaced bulb. Reassembled as ne eded and tested light by opening door. Works great.
Was this helpful?
Thank you for voting!
No heat
27 of 42 people found this instruction helpful.
  • Jaime from Chantilly, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Everything seems to work on the electric/gas dryer, but would not generate any heat. Did some research and ordered the thermal fuse & thermostat based on that. Replacement was simple and went well, however it did not fix the issue. Should have checked the continuity first as I found the "replaced parts" to be good. Have checked all ot her possible symptoms except the heating element, which requires addition labor. Overall, partselect portion was as advertised. All parts arrived quickly and were priced fair.
Was this helpful?
Thank you for voting!
The dryer stopped working and would not start.
20 of 22 people found this instruction helpful.
  • kevin from Saint Augustine, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
After unplugging the dryer, I removed the bottom panel in front. Remove the the filter inside the dryer and remove the filter housing below. There you can see the thermal fuse on the air duct, its white with two blue wires. You can check it with a ohmmeter after removing the wires. If its open its bad. Its held in place with two sheet met al screws. After replacing the thermal fuse the dryer worked fine. However I would suggest cleaning the air duct and the outside discharge opening. Hope this helps.
Was this helpful?
Thank you for voting!
The Dryer Would Not Turn On
19 of 19 people found this instruction helpful.
  • Ribhe from Wildwood, MO
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
The dryer wouldn’t turn on at all. It was like it was unplugged from the wall. However, fixing it couldn't be easier. I simply removed the back panel, found the fuse, tested it with an Ohmmeter (to determine that this was the part that didn't work), ordered the part from this website, and replaced the part. The part arrived in about t wo days. The shipping was a little pricey, but overall the whole thing cost me $20 vs. whatever it would cost me to get someone else to repair it. The website helps to identify the problem, and it is helpful to read how other people fixed their problems. It was so easy and the service was so good, I will definitely use this website again and recommend it to others.
Was this helpful?
Thank you for voting!
Noisy sound from dryer
20 of 23 people found this instruction helpful.
  • john from OLYMPIA, WA
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
Just like video except there were two screws in back to take control head off. Be prepared to have shop vacation ready. Clean dryer duct too. Have bandaids ready. Plastic triangles are not easy to take off, video makes it look easy.
Was this helpful?
Thank you for voting!
Idler Pulley broke
21 of 26 people found this instruction helpful.
  • Keith from Richmond, VA
  • Really Easy
  • 15 - 30 mins
  • Socket set
I disconnect the power, then the vent pipe. I removed the back panel of the dryer to access the pulley and removed the belt. Replaced the back and put everything back together.
Was this helpful?
Thank you for voting!
Moisture sensors need replacement
20 of 24 people found this instruction helpful.
  • Jack from JONESBORO, AR
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Inside the dryer tub, remove the filter housing by removing two phillips head screws. Unplug the sensor wires, note when replacing wires, black wire goes on upper sensor.
Separate filter grill from housing. Using the pliers, compress the tabs on the sensor plugs and push it thru the grill. The small blade screwdriver may come in h andy here to pry up on sensor to assist in pulling the plug end through the grill. Replace the sensors by hooking short end into grill and pushing the long end through the grill. When replacing the housing to the dryer, the most difficult thing is getting the screwdriver onto the recessed screws. Be sure to put the tab on top of the housing under the dryer frame when rotating the assembly into place.
Was this helpful?
Thank you for voting!
The sensor would not slide into grill
18 of 18 people found this instruction helpful.
  • sandra*broadnax from BRISTOW, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
Initially, i watched the how to do it instruction in the fix website to determine the complexity of repairs. The instruction built up my confidence. I ordered and recieved the grill amd the two new sensors. I placed the two new sensors into the new grill sensor slots. Then removed the old grill by unscrewing three screws. Connected th e two sensors positioned the grill and screwed in the three screws put the lent stray in the grill and closed the dyer door. I have been a happy camper ever since. I saved the $75 home insurance fee plus maintenence installment. Thanks
Was this helpful?
Thank you for voting!
dryer would not turn on
20 of 25 people found this instruction helpful.
  • harley from north lauderdale, FL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
checked to see what the problem might be according to your website, ordered the recommended parts, received parts within 3 business days, watched video on website with instructions, replaced parts and surprise, dryer works as if nothing ever happened. thank you for the straightforward, no nonsense information and video provided in your we bsite and the promt efficient service
Was this helpful?
Thank you for voting!
Washer would fill up, wash, then stop
22 of 31 people found this instruction helpful.
  • Glen from Plano, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I deduced the lid switch was the problem.

I removed the two screws holding the control panel on. Pulled the control panel back.
Disconnected the ground wire of the lid switch.
removed the two top clamps that hold the panel to the top of the machine.
Pulled back the casing (outside of the washer) and placed it on it's side on the floor. Here I could reach the switch. Removed old, installed new and reversed the process.

The part that gave me the biggest problem was setting the casing back on to the frame. You have to slide the front part in at the bottome, then lean back the rest of it.
Was this helpful?
Thank you for voting!
All Instructions for the 110629
61 - 75 of 1335