110623 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
One of the drum support rollers was worn out
13 of 19 people
found this instruction helpful.
-
David from Fleetwood, PA
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.
Other Parts Used:
Was this helpful?
Thank you for voting!
replace lint filter
10 of 11 people
found this instruction helpful.
-
Ed from Greensboro, NC
- Really Easy
- Less than 15 mins
with both hands
Was this helpful?
Thank you for voting!
The handle to my dryer broke
10 of 11 people
found this instruction helpful.
-
Elouise from ORLANDO, FL
- Really Easy
- Less than 15 mins
Just popped it into place needing no tools at all. Took less than a minute.
Was this helpful?
Thank you for voting!
would not stop when opening door during cycle
10 of 11 people
found this instruction helpful.
-
PHILIP from MATTHEWS, NC
- Really Easy
- 30 - 60 mins
-
Screw drivers
Found a U tube video to be useful. Remover 2 screws under the filter lid. Used a putty knife blabe wrapped in masking tape to unclip the lid. 2 screws to remove the switch. Biggest difficulty is seperating the electric connector. installed replacement switch and closed lid.....reality is this is a 15 minute repair. The extra time was to
... Read more
take the time to remove dust and lint from behind the dryer. Easy repair.
Read less
Was this helpful?
Thank you for voting!
Door switch was broken
11 of 14 people
found this instruction helpful.
-
Anthony from Orlando, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
I typed in on my brouser Repair Kitchen Aid Dryer door switch.
And on You Tube up came several videos showing me how to ewmove the switch and install the new one.
The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away fro ... Read more m the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada
And on You Tube up came several videos showing me how to ewmove the switch and install the new one.
The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away fro ... Read more m the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada
Read less
Was this helpful?
Thank you for voting!
Badly worn idler pulley and rollers.
11 of 14 people
found this instruction helpful.
-
TODD from GRASS VALLEY, CA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Braced dryer drum with a block. Removed the two rollers one at a time by using a screwdriver to pop off the triangular clip. Slid on new rollers. Would have been easier to remove the drum out the front instead of bracing it. Installed new idler pulley and belt. Dryer is 25 years old and sounds like a new one now when running.
Other Parts Used:
Was this helpful?
Thank you for voting!
the directions didn't say I needed clips to hold the felt in place while I did the glue
9 of 9 people
found this instruction helpful.
-
Todd from SAN JOSE, CA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Once I started using a bunch of clothespins to hold the felt in place and then started gluing small sections at a time I was able to complete the task. The glue comes out of the tube very quickly so don't squeeze it a lot.
Other Parts Used:
Was this helpful?
Thank you for voting!
Replaced a broken pulley.
10 of 12 people
found this instruction helpful.
-
Brian from IMLAY CITY, MI
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench set
Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.
Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.
Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.
Was this helpful?
Thank you for voting!
No heat on any applicable settings
9 of 9 people
found this instruction helpful.
-
Russell from LOUISVILLE, KY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Cleaned entire unit, replaced all thermostat assemblies and exhaust seal
Other Parts Used:
Was this helpful?
Thank you for voting!
burnt out bulb and broken switch
12 of 19 people
found this instruction helpful.
-
fanny from madison, WI
- Easy
- Less than 15 mins
-
Screw drivers
Both my husband and I are not good at DIY or fixing things. I watched the instruction video that was posted on the PartSelect web site. It seems easy to do it, however still very skeptical. My husband decided that there is nothing to lose in trying, so we ordered the parts. It is as easy and simple as the video instruction. We are very ha
... Read more
ppy customers.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The main knob insert snapped.
11 of 16 people
found this instruction helpful.
-
Larry from HICKORY, NC
- Very Easy
- Less than 15 mins
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat ... Read more es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat ... Read more es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Read less
Was this helpful?
Thank you for voting!
Old motor was making noise and tripping after a few minutes
10 of 13 people
found this instruction helpful.
-
John from Midland, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I disassembled the dryer once to clean the motor and compartment. After reasembly, the problem persistes. I ordered the motor and the second diasasssembly was accomplished in 10 minutes and the entire job took 45 minutes and the dryer was running like new. Tip- Leave the motor secured while removing the blower fan.
Was this helpful?
Thank you for voting!
Dryer belt broke- drum would not turn
10 of 13 people
found this instruction helpful.
-
Ronald from Oakdale, CT
- Easy
- 30 - 60 mins
-
Screw drivers
This was so much easier than I though it was going to be. Pulled up on the top part of the dryer and folded it over to the back. Removed 2 screws for the front panel and disconnected some wires. Laying down I fed the new belt on and made sure the tensioner was put back into the right spot, because when the belt broke the tensioner spru
... Read more
ng to the other end of its travel. Put everything back together. This was made super easy because you guys had the parts and the shipping was super fast. Alot of the local shops in the area didnt even carry the belt or were not helpful..
Read less
Was this helpful?
Thank you for voting!
Rollers were wore out
9 of 10 people
found this instruction helpful.
-
Chandra from Orange, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Just follow the instructions the one was provided with Maitanace kit we bought from you.
Was this helpful?
Thank you for voting!
Broken dryer door catch
9 of 11 people
found this instruction helpful.
-
Preston from ETNA, OH
- Really Easy
- Less than 15 mins
Used the screwdriver pressed the blade against the edge of the door catch and popped it out. Put the new door catch in place and pressed it and it snapped into place. Done
Was this helpful?
Thank you for voting!