1106117721 Kenmore Dryer - Instructions

All Instructions for the 1106117721
16 - 30 of 58

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
the cable for the dryer door broke.
4 of 4 people found this instruction helpful.
  • Todd from WESTERVILLE, OH
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
simple repair, pop the dryer lid, remove the screw for the front of the door. install cable and spring and then reassemble.

The only task that took some time was remembering to take out the screws for the lint port prior to lifting the lid.
Was this helpful?
Thank you for voting!
Dryer would not run
4 of 6 people found this instruction helpful.
  • james from york, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.
Was this helpful?
Thank you for voting!
Gasket was falling off, needed replacement
4 of 6 people found this instruction helpful.
  • Anthony from N. Ferrisburg, VT
  • Really Easy
  • Less than 15 mins
Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.
Was this helpful?
Thank you for voting!
the dryer would not turn on
4 of 6 people found this instruction helpful.
  • Warren from PHILADELPHIA, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
The first step was to check the electrical supply to make sure I had power 120 volt. I unplugged the dryer and turned off the gas supply and turned the dryer around so I could have access to the back panel removed panel to access the wiring harness and safety thermostats. All switches and wire checked good with my ohmmeter .I pulled off t he front kick panel and checked the electrical schematic and found the door switch was in the circuit to check it I had to lift up the top and pop out the front to access the door switch checked switch and found it defective. Replaced switch vacuumed out dryer and vent reassembled dryer and all worked good.
Was this helpful?
Thank you for voting!
belt was cracking and dryer was somewhat noisy
4 of 7 people found this instruction helpful.
  • Melody from Silverton, CO
  • Easy
  • More than 2 hours
  • Nutdriver, Screw drivers
I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, rol ler, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.
Was this helpful?
Thank you for voting!
Dryer drum wouldn't turn and motor would shut off
3 of 4 people found this instruction helpful.
  • Cynthia M from Westfield, MA
  • Easy
  • More than 2 hours
  • Screw drivers
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
Was this helpful?
Thank you for voting!
Bulb worked for a couple days and has now burned out, filaments dangling
3 of 4 people found this instruction helpful.
  • Amy from JUNCTION, TX
  • Easy
  • Less than 15 mins
  • Screw drivers
To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.
Was this helpful?
Thank you for voting!
Door switch would not let dryer operate
2 of 2 people found this instruction helpful.
  • George from Rio Communities, NM
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top bac k out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people found this instruction helpful.
  • Yafa (and David) from Bothell, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Blower belt broke on my 58 year old Kenmore gas dryer.
2 of 2 people found this instruction helpful.
  • Mary from KENNESAW, GA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Called my son. He took off the back put the belt on and we were ready to go.
Was this helpful?
Thank you for voting!
broken door cables
2 of 2 people found this instruction helpful.
  • Richard from LA BELLE, PA
  • Really Easy
  • 30 - 60 mins
followed directions that came with order confirmation e-mail
Was this helpful?
Thank you for voting!
Wen the dryer gets hot but dry anything when it runs and no air comes through the filter opening with the filter out
2 of 2 people found this instruction helpful.
  • Willis from FORT WORTH, TX
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
First diagnose the problem. No air coming out the exhaust or filter, things aren’t drying, you can’t hear the blower running.
Fuses or breakers are verified ok and on.
Turn dryer off. Disconnect exhaust tubing after unscrewing it’s clamp. Drag the dryer away from the wall to get access to the back and unplug the 220 v power cab le from its socket. Get behind the dryer to remove its back cover plate by unscrewing its holding screws with screwdriver or small socket wrenches.
Vacuum out the back of the dryer removing the powdery dust around the blower motor and pulley and remove the old belt.
Since there is no adjustment arm, you have to stretch the belt around the rim of the blower pulley with both thumbs pulling upward against the motor pulley below.
After the belt is in place you can pull on it to be sure both pulleys rotate so the blower fan will rotate. Then just put the back plate on the dryer, replug it in, push it back enough to hook up the exhaust pipe and push the dryer back to its home spot.
Turn it on and you’re ready to go. Then order a spare belt for the future in about 5 + years.
Was this helpful?
Thank you for voting!
Dryer would not start.
2 of 3 people found this instruction helpful.
  • Victoria from Roslyn Heights, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect ag ain. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.
Was this helpful?
Thank you for voting!
water wouldn't run out of washer
4 of 9 people found this instruction helpful.
  • James from Richmond, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.
Was this helpful?
Thank you for voting!
Won't pump out the water
1 person found this instruction helpful.
  • Victor from NORFOLK, VA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Was this helpful?
Thank you for voting!
All Instructions for the 1106117721
16 - 30 of 58