110609 Kenmore Dryer - Instructions

All Instructions for the 110609
121 - 135 of 664

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer would not heat.
7 of 11 people found this instruction helpful.
  • Russell from Orlando, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Watched on-line video on how to disassemble and test heater element, thermostat, and hi-temp shut down. Heater element was open. Ordered new heater element. Re-installed heater element iaw video provided with parts. Video provide was one of the best I've seen. Explanation on releasing access panel was especially helpful.
Was this helpful?
Thank you for voting!
Dryer was Noisy
6 of 8 people found this instruction helpful.
  • Doug from HARRODSBURG, KY
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I simply followed the video and apart from a couple of areas that were not relevant to my model, everything went exactly as illustrated. The video is excellent and made the repair so easy.

The only issue I experienced was being short two rollers, as the parts diagram did not clearly show that there were two rollers in the back and two in the front.

A kit, with its own part number should be prepared that would show 4 rollers and belt as the recommended required parts.

It was an easy fix, I just did half the install a second time.
Was this helpful?
Thank you for voting!
Drum support roller making very loud noise
5 of 5 people found this instruction helpful.
  • William from TROY, AL
  • Really Easy
  • 1- 2 hours
  • Screw drivers, Socket set
had to take front off of Dryer then was able to replace drum roller
Was this helpful?
Thank you for voting!
Screen on the hot air vent disintegrated
5 of 5 people found this instruction helpful.
  • Thomas from Edgartown, MA
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
It is odd that this part needed replacement but I am in an area near the Atlantic ocean in a vacation house which is vacant most of the year. The exhaust vent probably brings excessive moisture down to the dryer in the basement. The screen you can see at the inside back of the tumbler (where the heated air enters) rotten out, pieces fell inside and there was danger of something falling in and catching fire. I found no useful source for information (including YouTube) as this part is most easily replaced from the rear of the dryer and the available info was about repairing the heating element, the circuit board, or the exhaust venting pieces which is done from the front.

The bottom line is that the back removes easily. You should:
1. unplug and remove the exhaust shoot
2. remove the top per YouTube or other source
3. take off the back panel over the electrical connections and unscrew the ground; tuck it inside. Don't undo any electrical connections except the ground
4. take off the screws holding the back on (8-9, one is hidden above the exhaust vent) and pull it out of the way; you then have compete access to the "DUCT-AIR" part
4. undo the clip that holds the vent tube (from the heating element) to the part
5. remove the screws that hold the part to the inside back (3?) and push it out of the way
6. remove the clips and remove the old part
7. reassemble in reverse order

I'm over 70 so I took lots of time and breaks but was still done in under two hours. The 2 clips holding the heater element tube to the part were badly rusted and should have been replaced but I made do with the old ones.
Was this helpful?
Thank you for voting!
Dryer not heating
5 of 5 people found this instruction helpful.
  • John from CLARKSBURG, WV
  • Easy
  • 1- 2 hours
  • Socket set, Wrench (Adjustable)
Replaced the heating element. Took the front lower panel off, 2 screws one on each end, removed cover on left side over blower 3 screws and removed cover lower right side over heating element 2 screws. Removed 6 wires plugged into heating element cover, turned heater element cover counter clockwise and pulled out. Removed 1 screw hold ing heating element inside of cover, pulled out heating element. Replaced heating element back in cover putting screw back in to hold it. Put heating element and cover into hole in back of dryer turning clockwise to secure. Then put cover holding heating element over the front of it and secured with 2 screws. Put blower cover back secured with the 3 screws and put the front cover back on securing with 2 screws. dryer is heating better than ever.
Was this helpful?
Thank you for voting!
Dryer Start button wouldn't stay on
5 of 6 people found this instruction helpful.
  • Eileen from GROVELAND, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
After watching a video from youtube: which happened to have the same issue and exact dryer, I realized it was the start button relay and not the switch. The video covers how to test if its the relay. I did mark all the wires with tape and labeled them so I made sure they were reconnected appropriately. I ordered the relay and it was ins talled in mere minutes. This is the first ever appliance repair I have ever done! It was a great feeling to know I was able to fix my dryer and it only required a screwdriver and a few minutes!
Was this helpful?
Thank you for voting!
Drum would not spin to drain water
9 of 18 people found this instruction helpful.
  • Gay from Apple Valley, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.
Was this helpful?
Thank you for voting!
Dryer made squeaking noise, then more of a rumbling noise.
5 of 6 people found this instruction helpful.
  • JAMES from NORTH OLMSTED, OH
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Socket set, Wrench set
Checked this site for most likely needed parts and ordered. Located full repair manual inside unit after removing lid. Followed instructions in manual to take apart and remove the drum; took pictures at each removal step and used pill organizer to keep screws in correct order and quantity. The metal cylinder in the center of the idler pul ley had ground away so the idler pulley with bracket was replaced. (There was a lot of metal dust that had to be cleaned.) One of the rollers did not turn smoothly so that was also replaced. After putting drum back in, reversed the steps to reassemble and referred to photos to make sure did in correct order and did not forget anything.
Was this helpful?
Thank you for voting!
Dryer would not start.
6 of 9 people found this instruction helpful.
  • John from HATFIELD, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
With the help of YouTube, I was able to watch videos of how to disassemble and reassemble the dryer. I watched a video showing where the Thermal fuse and Thermostat was located as well as how to test them with a meter. I watched another video showing how to replace the drum belt, showing step by step instructions. Without YouTube it would have been a whole different story!
Was this helpful?
Thank you for voting!
When door was closed the timer could be heard to continue clicking. also, drying cycle started immediately upon closing the door.
5 of 7 people found this instruction helpful.
  • Theodore from Baraboo, WI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Two screws hold the top control panel in place. Once removed the panel could be tipped forward. The Push to Start switch had 2 wires which were removed and swapped to the new starter switch. The old one rotated 90 degrees to remove and the new one installed. Panel was resecured to the top of the dryer and tested. Worked first time. Finding the part on the website, ordering it, receiving it quickly and the install couldn't have been easier or more pleasant or efficient.
Was this helpful?
Thank you for voting!
Taking 90 minutes + to dry one load
5 of 7 people found this instruction helpful.
  • Bryan from newington, CT
  • Easy
  • 15 - 30 mins
  • Socket set
Removed the back of the dryer about 8 screws. Removed the Thermostat 250 F and replaced with new. Dries a load of clothes in one cycle on medium. Not bad for a 16 dollar part. I am a computer tech and I am used to taking computers a part but I think most people that are in anyway mechanically inclined and can look at a diagram could d o this and save yourself a lot of money.
Was this helpful?
Thank you for voting!
Dryer would not stay running if I placed the timer on anything above 30 min
4 of 4 people found this instruction helpful.
  • Cristy from HARROGATE, TN
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
I took the timer knob off, then took the back off. I then took a picture of the so I would know how the wires would go back but I didn't need because the timer is labeled. I then took the timer out snapped wires off then replaced them on the new one and bolted it back it. It was very easy and took less than 15 min to do.
Was this helpful?
Thank you for voting!
Timer would not stop.
4 of 4 people found this instruction helpful.
  • Sidney from Stokes, NC
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Cut power at breaker panel to Dryer.
Remove back cover of controls panel by removing six screws. Removed control knob and one screw from timer. Removed wires from bad timer (one at a time) and put them on new timer. Installed new timer in control panel and replaced the knob and screw on front. Then replaced panel on back of control panel. Cut power back on at breaker panel and tested unit for proper operation.
Was this helpful?
Thank you for voting!
Broken Drum Belt
4 of 4 people found this instruction helpful.
  • Garry from Garland, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
Just like the video, just followed the video
Thanks,
Was this helpful?
Thank you for voting!
drier would not heat up
5 of 7 people found this instruction helpful.
  • PATRICK from PALOS PARK, AL
  • Easy
  • Less than 15 mins
  • Screw drivers
i took off the back of the drier and with a screw driver removed the 2 screws and put the new part on
Was this helpful?
Thank you for voting!
All Instructions for the 110609
121 - 135 of 664