- Home
- 1106008713
- Instructions
1106008713 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
door catch broke therefore dryer door would not close
1 person
found this instruction helpful.
-
vernette from sprague, WA
- Really Easy
- Less than 15 mins
just put the new part in the door---sooo easy! THANK YOU!
Was this helpful?
Thank you for voting!
Seal snapped, which lead to longer dry cycles.
2 of 4 people
found this instruction helpful.
-
Christian from Sunapee, NH
- Really Easy
- Less than 15 mins
Just slipped it on, it was very simple. My dry cylces were reduced. Worth the $15 I spent to get the part!!!!
Was this helpful?
Thank you for voting!
dryer door wouldn't catch, catch was broken
1 person
found this instruction helpful.
-
Theodore from Tyler, TX
- Really Easy
- Less than 15 mins
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
Was this helpful?
Thank you for voting!
broken door catch
2 of 4 people
found this instruction helpful.
-
Michael from Goddard, KS
- Really Easy
- Less than 15 mins
the part fit perfectly, it just snaped right into place.
Was this helpful?
Thank you for voting!
door latch broke
1 person
found this instruction helpful.
-
Debra from Oakland, NJ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pop out the old latch and replaced with a new one
Was this helpful?
Thank you for voting!
catch was missing to close dryer door
2 of 4 people
found this instruction helpful.
-
DONNA from SAN LORENZO, CA
- Really Easy
- Less than 15 mins
The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)
Was this helpful?
Thank you for voting!
broken door catch
1 person
found this instruction helpful.
-
Susan from HUDSON, MA
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
I followed your short video and found it very easy to do
Was this helpful?
Thank you for voting!
Machine would not start and light stayed on with door closed.
1 person
found this instruction helpful.
-
Mark from TERREBONNE, OR
- Very Easy
- Less than 15 mins
-
Screw drivers
Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allo
... Read more
w top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.
Read less
Was this helpful?
Thank you for voting!
broken door catch
1 person
found this instruction helpful.
-
Frank from ENDICOTT, NY
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this helpful?
Thank you for voting!
latch was broke
1 person
found this instruction helpful.
-
Rick from SAN DIEGO, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
just followed the video directions, worked perfectly thanks
Was this helpful?
Thank you for voting!
dryer would not run because catch did not hold tight enough to press door switch.
1 person
found this instruction helpful.
-
j from TAZEWELL, TN
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this helpful?
Thank you for voting!
Door catch was cracked
1 person
found this instruction helpful.
-
Tammy from glenford, OH
- Very Easy
- Less than 15 mins
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Was this helpful?
Thank you for voting!
Door would not stay closed - so dryer kept shutting off
1 person
found this instruction helpful.
-
Barbara from NORTH EASTON, MA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Followed Youtube video - quick & easy
Was this helpful?
Thank you for voting!
Broken dryer door catch
1 person
found this instruction helpful.
-
Kenneth from UPPR MARLBORO, MD
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Was this helpful?
Thank you for voting!
Door wouldn't fasten shut
1 of 2 people
found this instruction helpful.
-
Susan from Laingsburg, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
Popped the latch out and popped a new one in.
The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your se ... Read more rvice. You made my life easier.
The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your se ... Read more rvice. You made my life easier.
Read less
Was this helpful?
Thank you for voting!