1106007 Kenmore Dryer - Instructions

All Instructions for the 1106007
91 - 105 of 666

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer runs heats up, will run for a short period and then shuts down, after a minute or two it will come back on and will resume drying.
18 of 36 people found this instruction helpful.
  • John from Brookings,, OR
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench set
Replaced the thermastat first, then the cutoff switch, still the same, I then replaced the thermister, and still have the problem.
Was this helpful?
Thank you for voting!
Dryer squeeching very loud
9 of 9 people found this instruction helpful.
  • Michael from ENOLA, PA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done
Was this helpful?
Thank you for voting!
gasket came off lent filter
11 of 15 people found this instruction helpful.
  • stephen from langley, KY
  • Really Easy
  • Less than 15 mins
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people found this instruction helpful.
  • Dawn from Chesapeake City, MD
  • Really Easy
  • Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
Freezer Cooling Problems - would get too warm then too cold. Condenser fan would run sometime but not always
10 of 13 people found this instruction helpful.
  • JAMES from Middleboro, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Unplug
Remove entire back panel (both chipboard and metal fan grill)
Unscrew both fan mount plate screws - fan won't be able to come out because it is still plugged in
When looking at back of fridge, locate a small plastic box to the immediate left of the condenser. It's a circuit block. Release the metal spring clip hold ing the plastic cover in place, and trace the fan wire connections back to the fan. Make a note of which wire is connected to which terminal (1 of the fan wires has white lettering and 1 is just black)
Unplug both fan wire connects from circuit block to release the fan power cable.
Remove the fan mounting plate
Release fan blade clip by pressing fan against motor and unscrewing and remove fan blades
Unscrew motor from brackets - note alignment of motor on brackets
Mount new motor on brackets. Leave plug wire disconnected (replacement motor has a harnessed plug wire)
Connect new plug wire to the circuit block keeping wires connected to the proper terminals
Snake new plug wire behind condenser like the old wire was and run through cable bracket to the back right of the condenser
Plug wire harness into motor and re-mount fan mount plate
Reattach fan blade and secure using blade mount kit
Replace back panels
Was this helpful?
Thank you for voting!
fan had stopped-freezer not performing etc.
8 of 8 people found this instruction helpful.
  • George from Glenwood, MN
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers
simply removed old motor and replaced new. I'm over 82 and it was hard to get down and up to floor level!! One thing was a little puzeling -that was to insert the right screws which had a nitch in the end of the threds to keep it from loosening- I thought I was spoiling the threds cause I had to use a little pressure to start the screws and thought I had the wrong screws--they had sent several sets of them for different name brands- but II got it and everything seems to be allright - Could you tell me if I could purchase a replacement compressor and some refrigerent -the new kind. thank you, George Erlandson Only if my comp. goes out!!!
Was this helpful?
Thank you for voting!
The old door catch failed. Clothes won't dry with door open !
8 of 8 people found this instruction helpful.
  • Theresa from Norfolk, VA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Old door catch came out, new one slipped in. All works great.
Was this helpful?
Thank you for voting!
No heat in dryer
10 of 14 people found this instruction helpful.
  • Noah from Maiden, NC
  • Really Easy
  • Less than 15 mins
  • Wrench (Adjustable)
Took off the lower front panel, removed duct piece from filter to blower fan, removed two screws and two wires to thermostat in exhaust ducting, then replaced thermostat with new one. Very easy job and everything worked like new when I reassembled it.
Was this helpful?
Thank you for voting!
Not heating
8 of 9 people found this instruction helpful.
  • Manuel from Key Biscayne, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
So simple.... I have no idea how to fix anything but I took a crack it. Looked inside and pulled out the resistor. I noticed the coil was broken so I replaced it with a newn part and reinstalled it. Worked like a charm. Saved myself alot of money!!!!
Was this helpful?
Thank you for voting!
Dryer Would Not Heat
8 of 10 people found this instruction helpful.
  • John from Raleigh, NC
  • Easy
  • 15 - 30 mins
  • Socket set
The dryer stopped heating. Took the front lower panel off of the dryer and obtained the troubleshooting instructions stored there. Used an ohmmeter (most volt meters also have an ohmmeter) and tested all the electrical components one by one (thermostat, thermal fuse, heater coil - following the troubleshooting instructions provided with the dryer) and found that I didn't have any resistance across my heater element. Removed it and sure enough there was a break in the heater coil. Ordered a new heater element from PartSelect for less than $50 and replaced it myself. Saved myself a good bit of money repairing my dryer myself. It was very straight forward and easy. If you can follow easy to read instructions you can do it.
Was this helpful?
Thank you for voting!
The Door Switch Actuator Spring had broken
8 of 10 people found this instruction helpful.
  • Norman from Allen, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
I took the dryer apart by visually looking at it and removing screws, etc. until I had the top off and the front off. I took the dryer apart so I could get the part out and use it visually ascertain I was ordering the same part.

I bought the replacement part and only then did I have the instructions to take the dryer apart. I t was further apart than the instructions said. I had to take the front off to retrieve the broken part which had fallen inside the front of the dryer.

I put the front back on the dryer and installed the new part, which, fortunately could only be installed one way. Once I had the two screws tightened into the part, the remainder was to simply follow the instructions that came from your web site and put the link filter and top of the dryer back on. Of course, I plugged in the dryer and checked to see that it ran before completing this.

I am amazed that I was able to find this part for a 30 year old dryer. The part hasn't changed at all. I guess, if you have a good part, there's no need to modify it.
Was this helpful?
Thank you for voting!
Dryer would not turn on
8 of 10 people found this instruction helpful.
  • Pam from Chandler, AZ
  • Really Easy
  • Less than 15 mins
  • Socket set
We took the screws off of the back, took out the thermal fuse and replaced it with the new one.
We watched a video of how to do it which made it so easy.
Works great!
Was this helpful?
Thank you for voting!
The dryer door latch broke
9 of 13 people found this instruction helpful.
  • Theresa from Topeka, KS
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.
Was this helpful?
Thank you for voting!
Dryer working, but not heating
9 of 13 people found this instruction helpful.
  • Amy from Birmingham, AL
  • Really Easy
  • Less than 15 mins
  • Socket set, Wrench set
Took back cover off
Disconnected part
Put new one in
Reconnected wires
Put back cover on

To verify that this was the needed part, I used a digital multimeter to confirm there was no continuity.
Was this helpful?
Thank you for voting!
Broken Door Handle on Front of Dryer
13 of 26 people found this instruction helpful.
  • Jeff from Wausau, WI
  • Really Easy
  • Less than 15 mins
Do to age and heat the dryer door handle was brittle and broke. Ordering was easy on line. Part was delivered faster tan expected. Oh and the repair time, Less than 1-minute.

Thanks for the great service.
Was this helpful?
Thank you for voting!
All Instructions for the 1106007
91 - 105 of 666