1105810106 Kenmore Washer Dryer Combo - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken
-
Tomas from Orlando, FL, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
low or no heat
Removed back cover of entire dryer.The thermostat was accessible from that point(Just as diagram showed), removed two wires from thermostat, removed thermostat & replaced with new thermostat & plugged 2 wires back in just as instructions indicated. Very simple,15 minute job. I will certainly use again for any appliance repairs.
Parts Used:
-
charles from bryan, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
no heat
ordered wrong limit switch had to reorder right switch and decided to replace the heater element as well. works fine now
Parts Used:
-
Dan from Thomasboro, IL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!
Washer/Dryer would not start
Neither the washer or the dryer of the stacked unit would start. The website suggested that one of the causes could be the thermostat. I ordered a replacement that arrived quickly. Swapping the part only took minutes, and it started just fine.
Parts Used:
-
James from Salt Lake City, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Stopped and would not restart / start.
1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed the previous procedures to complete repair.
Parts Used:
-
Patricia from Duck, WV
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
not enough heat to dry clothes
always unplug from outlet first, unscrewed the back off and pull off the wire from cycling thermostat ,take the two screw out that holding it in place and replace the new one .Very simple and easy. Thank you for the easy step by step video to complete this repair. James
Parts Used:
-
James C. from Cobbs Creek, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Dryer Not Drying Clothes on first cycle
Took the back off the dryer. Disconnected the old thermostat and installed the new thermostat. Connected the back of dryer. Put in a load of clothes to dry and the clothes were dry on the first try. Works like a new dryer. Saved a lot of money not having to buy a new dryer when all I had to do was replace some old parts.
Parts Used:
-
Thomas from Glenpool, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
dryer wouldn't start
I found on youtube that there are directions to repair. Dryer problems are usually one of three things, the door switch being one of them. i checked this last (should have been first). ordered the part( about 65% off sear's cost) and it came in one day! It went on really easy as long as you knew from repair video how to access inside. almost spent $400.00 on a new one.
Parts Used:
-
sean from easthampton, MA
-
Difficulty Level:Easy
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!