1105809704 Kenmore Washer Dryer Combo - Instructions

Replaced lid switch, but problem still continued.

Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.

Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3

I removed the 2 crisper drawers and the glass shelf directly above the Pantry Drawer. Removed the Pantry Drawer and Pantry Drawer cover so you have easy access to the Right-Hand End Cap. On the right-hand End Cap, there are 2 screws which hold the End Cap in place, use a 1/4 inch driver to unscrew the screws from the front of the cabinet on the End Cap and half-way in of the cabinet, leave the screws in their holes in the End Cap. Lift gently to get off a small plastic pin, and move the End Cap away from the Cabinet. You don't need to completely pull the End Cap out of the cabinet, it'll move more like a door opening. Place 2 washers on each screw and gently put the End Cap back into place, being careful NOT to jostle too much so the washers don't fall off the screws. You will need to gently lift the End Cap back in to place over the plastic pin. Hand-tighten the screws back into place with the 1/4 in driver. Remount the Pantry Drawer on the sliders. When you go to install the Pantry Drawer Cover, you will need to gently push on one of the pins to get the cover back into place. Put glass and crisper drawers back into place.

Test by gently pulling on the Pantry Drawer. If properly mounted, the pins will extend fully into the Cover and will keep it secure when opening the Pantry Drawer.

Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.

Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

replace the water valve

My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.

I found on youtube that there are directions to repair. Dryer problems are usually one of three things, the door switch being one of them. i checked this last (should have been first). ordered the part( about 65% off sear's cost) and it came in one day! It went on really easy as long as you knew from repair video how to access inside. almost spent $400.00 on a new one.

I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the location and design of the switch. I got it though.

This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.

1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed the previous procedures to complete repair.

Removed the old one installed the new one