11047761800 Kenmore Washer - Instructions

removed 3 screws from back, then pulled hose of piece and disconnected wire clip. reassembled. have tu turn bottom of the piece torward you to remove from machine. this part is located on the back right side, black on my machine 1x2x2/4 inches in size, this is looking down into the wash machine from the front.

Take off top of washer and the flowmeter is in the back lefthand corner on the top of the washer. Replaced the water level switch on the top righthand of the machine also. Got about 150. 00 Total invested w/service call from local tech. F-20 has not came back yet. I hoped it fixed it washer is only 3 yrs. Old. -Gd

I had to cut new slots in the metal base of the machine cabinet to accommodate the different configuration for the rubber boot assembly. Thankfully the new pump works like a charm.

Starting getting these errors...but we had also been washing about 300 towels a week from our gym for about 3 months. I contacted an ex-sears repairman friend of ours for advise. He first recommended checking the pump filter basket. It was easy to get to by taking off the front panel. It did have about three hand wipes and other debris in it. Removing these items did cause the errors to occur less often, but they still did continue. We had our repair friend come over and go through the diagnostics checks as per the instruction sheet that was on the inside of the washer. It came down to being the pressure sensor. After replacing the sensor, the washer has worked flawlessly.

Removed 3 screws from back of top panel, slid top off, twisted APS sensor 90 degrees, popped out of mount, removed hose and elect. connector, replaced with new APS sensor and reinstalled. Ran diag test, passed with no issues.

Peace of cake! 3 screws at top of washer to gain access.
Unplug sensor, but first have to rotate sensor 90 degrees to release from bracket. unplug black tiny hose and plug wire from sensor. Install new in reverse order.
works great and saved a lot of cash doing it myself.
Grateful for the info for the tips from other's with same problem!
Mark from Vermont
Happy Camper:)))))))))

.

Easy fix,
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier.
Good luck on your repair

removed door from washer, set flat on table and just loosen up the screws all around, removed old hinge and replaced with new hinge, very easy. back to washing clothes.

Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement broke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.

Removed the old hoses and screwed on the new hoses.

First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.

Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip

Removed door from washer, remove hinge from door. Then slip in hinge and tighten hinge to door. Then attach door. It works and the most important thing the wife is happy

take the back cover off and put belt on. the belt is a tight fit and requires sone effort, but can be done.

I just took off the old part and installed the new one. The new part was a bit different.