1104753 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
would not drain or spin
-
DAVID from HARRAH, OK
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Replace water pump
Was this helpful?
Thank you for voting!
Making noise, not draining properly.
-
Keith from Dayton, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Put towel down to catch excess water, opened drain screen, used pliers to remove squeeze clamps on both hoses, removed front hold-down torx-head bolt and slid pump assembly out. Compared new part to old and found 2 differences 1:no hold-down location in front for bolt,2: the rubber padded feet are not the same. I was able to remove the tw
... Read more
o screws on the right side and use just the rubber pad for support while sliding the left side in the slot and is was plenty stable and works just fine. I guess the Whirlpool Duet model is a bit different on mounting but everything else fit quite well, the washer is working perfectly again.
Read less
Was this helpful?
Thank you for voting!
It was making lots of noise. Halfway through the cycle it would not pump all the water out
-
Duane from New Richland, MN
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
First unplug the washer. Make sure and drain washer completely. If not drained remove front panel , Remove 2.5 inch Plastic drain cover which has a catch bin on it. This will allow it to drain the washer. Put pan underneath to catch the water. Tip washer back and prop up with something 6 inches tall to get to the screws underneath.
... Read more
A cement block would work well. Use pliers to squeeze hose clamp together to remove the Hoses. Gently lift up The flip down cover Over the top of the wire harness Push in the tab on the wire harness, Gently pull back on the wire harness. Remove two mountings screws from the bottom of the washer. Slide the whole pump housing to the right and Lift up. Now the pump is been removed. Inspect inside the hoses For Debrie. Remove anything that is left in the hoses. Reinstall the pump in reverse order from the way you took it off. Leave front panel off Make sure all hoses and wire harness are hooked up. Run wash cycle to make sure there are no leaks. Do not put hands in while running. If no leaks replace front panel. Not sure if this is the right way But this is the way we did it and it worked well. Washer runs quieter now than it did when we got it
Read less
Was this helpful?
Thank you for voting!
The washer was flashing f-21 code. And the cloths were soaked.
-
Steven from Kalamazoo, MI
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
First thing, unpluged the washer. I removed the lower front acces panal. I then propped the washer up on 2 pint sized paint cans to reach the pump mounting screws. I disconnected the wire bundle going to the pump. Then removed the inlet and outlet hoses from the pump. Then I removed the 2 mounting screws on bottom and slide the pump to th
... Read more
e left and removed. I then pump the new pump on the same way I took the old one off, but in reverse. Easy and fast the worst part was the price of the pump.
Read less
Was this helpful?
Thank you for voting!
Wouldn't drain
-
Dagmar from Edwardsville, KS
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I was already very familiar with the motor & drain pump, as I had disassembled my original one in attempt to find the problem & fix it. Finally, I broke down & purchased a new one. It was VERY easy to install! The most difficulty was finding the right sized board to put underneath & raise the machine up (with the dryer attached to the
... Read more
top of it) to place the board underneath so that I could tighten the bolts from underneath to attach the pump. After that was over, the rest was cake! Just attach the hoses & the electrical, which just clips in place & my washer is like new again! Yay! Oh, and yes, I'm a woman DIY'er.
Read less
Was this helpful?
Thank you for voting!
F 21 error
-
Belinda from Havre, MT
- Really Easy
- 15 - 30 mins
-
Wrench (Adjustable)
We purchased a new pump and installed it very easily. My washer works great!
Was this helpful?
Thank you for voting!
Washer wasn't draining and spin cycle not working
-
Chris from Spanish Fort, AL
- Easy
- 15 - 30 mins
-
Pliers, Wrench set
Followed instructions from a You Tube video. I'd recently lost my job and money is tight and I thought we could save money doing it myself. By watching the video and ordering parts from you we were able to save $500 between parts and labor. Thanks
Was this helpful?
Thank you for voting!
water leaked thru bottom of door, torn bellow/door gasket
-
Ben from Hernden, VA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
the hardest part of the repair is having the confidence to pull all the screws and remove door etc. Dish soap was a good trick when I needed the last bit of the bellow to pop/stretch into place in step 1 of attaching the bellow.
Was this helpful?
Thank you for voting!
Leaking water in tub when not in use.
-
William from Charleston, MS
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Received water valve in three days, remove top on washer, removed old part and replaced valve with new one, real easy fix, any one could do this. PartSelect confirmed this was the problem and part I needed.
Was this helpful?
Thank you for voting!
needed to replace water pump
-
Tina from Denver, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench set
dryer stacked on top of washer. had to lift washer and block w/2 x 4 to get under unit and replace pump
Was this helpful?
Thank you for voting!
F21 code
-
Mike from Columbus Grove, OH
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Thank You so much for the other stories folks wrote on here! We were getting an F21 code on a regular basis. After finding a necklace and about $2.50 in change in the filter tray we found the problem. Over time I thought the washer was getting louder but it was so gradule that we really did not realize it.I had read other posts on here an
... Read more
d ordered a new pump. After taking out 3 screws and 2 clamps the pump came right out and went in just as easy. Less than 15 minutes and we were back in business with a wisper quiet washing machine,Thanks Again everyone, Mike D.
Read less
Was this helpful?
Thank you for voting!
drain pump impellar busted
-
jeremiah from royalton, MN
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Socket set
I drained the water out of the pump area. Then took off all clamps and holding brackets. Next I pulled off the quick connect power plug. Then I put new pump in the way I took old pump out. The hardest part was unscrewing the bracket from underneath the washer. Cloth washer working fine.
Was this helpful?
Thank you for voting!
Drain Pump Stopped working
-
Julie from Milton, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took of the panel, unscrewed the old drain, screwed the new drain in. Very very simple to do! The first part I received leaked, I called customer service and they gave me a refund and express shipped a new part - no questions asked. Very good customer service!
Was this helpful?
Thank you for voting!
buzzing noise water not draining
-
brian from turners falls, MA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
unplug washer from outlet carefully tilt back to get at underside of washer remove bottom panel. pump location lower right front. remove two hoses from back using pliers keep note on hose location. remove two bolts on underside of machine slide pump to the right to release from rubber holders to install reverse the process also good idea
... Read more
to use the new hose clamps that come with your new pump and the rubber mounts if they are included
Read less
Was this helpful?
Thank you for voting!
drive belt
-
Casey from Stillwater, OK
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
very easy to take off the bad belt and easy to put the other on. skill level would be a low anyone with a socet rench and a screw driver can replace the drive belt. shipping was extremly fast. 3-6 day shipping was there in 2 days.
Was this helpful?
Thank you for voting!