110458 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Constant washer Faulting with a FH fault code
15 of 18 people
found this instruction helpful.
-
Bruce from Salisbury, MD
- Easy
- Less than 15 mins
-
Nutdriver, Pliers, Socket set
This washer had been faulting since it was 1 year old but it only happened 1 to 2 times a year. As the fault problem became more often, I realized it was a hardware or computer malfunction. But what was the problem? Well the problem always was a faulty flow meter. I replace the valve and the flow meter. But I tested the flow meter several
... Read more
times.-- I replaced the flow meter and the valve. And for once in 5 years it did not fault.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Detergent leaking under Dispenser Drawer down front of Washer
30 of 63 people
found this instruction helpful.
-
Geof from Garner, NC
- Really Easy
- 15 - 30 mins
Secondary problem was bleach being siphoned from dispenser prematurely when drawer slid in. Replaced Drawer, Detergent Container and Bleach Siphon parts. Appears to have been a change in the siphon design when compared to the original factory part. 5 loads completed since replacement of these parts with no premature siphon of bleach or
... Read more
leakage down the front of the washer.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Low water intake pressure error
13 of 13 people
found this instruction helpful.
-
John from Rye Brook, NY
- Easy
- 15 - 30 mins
-
Pliers, Socket set
Serviceman had previously replaced the hot and cold inlet valves, but the low pressure error persisted. Rather than cough up another $130 for the serviceman to return, plus parts and time, I decided to order the replacement flowmeter from PartSelect.
Unplug power and turn off water. Top of machine comes off by removing three sc ... Read more rews at top rear; use socket, spanner or T20 driver. Unplug electric sensor from flowmeter. Old unit is removed, and new one connected to water line by squeezing spring-clips with a pair of flat nose pliers. Reconnect electric sensor.
Great move, easy, and saved myself the thick end of $200.
Unplug power and turn off water. Top of machine comes off by removing three sc ... Read more rews at top rear; use socket, spanner or T20 driver. Unplug electric sensor from flowmeter. Old unit is removed, and new one connected to water line by squeezing spring-clips with a pair of flat nose pliers. Reconnect electric sensor.
Great move, easy, and saved myself the thick end of $200.
Read less
Was this helpful?
Thank you for voting!
Worn out hose had a hole it it.
16 of 23 people
found this instruction helpful.
-
Edward from Clinton, MD
- Easy
- 15 - 30 mins
-
Pliers
I romoved the front of the washer access panel. I then used the pliers to remove the clamps from the old hose and to replaceit with the new one.
Was this helpful?
Thank you for voting!
Door leaked water
14 of 19 people
found this instruction helpful.
-
Tom from Spirit Lake, IA
- Easy
- 15 - 30 mins
-
Screw drivers
First step was to remove old bellow. I opened the door there is a small wire with a spring attach that holds the outside of the bellow to thw washer. Then removed it from the water inlet, then took a short straight scewdriver to remove the gaint hose clamp holding it to the drum. Installed the new part. When putting hose clamp back on I r
... Read more
emoved the top of the washer by removing the three screws in the back then I flipped the hose clamp so I could use a long screwdiver from the top side.This will give you alot more room. Hope this helps
Read less
Was this helpful?
Thank you for voting!
Baffle broke and became disconnected from drum
13 of 16 people
found this instruction helpful.
-
Gregory from Geneva, IL
- Really Easy
- Less than 15 mins
slid new baffle into place. No directions with new part, fortunately it was easy to figure out how baffle locked into place.
Was this helpful?
Thank you for voting!
Washer would not operate, water in drum would not drain. Error code indicated a bad pump
12 of 13 people
found this instruction helpful.
-
Patrick from Beaumont, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed three mounting screws to the front access panel, removed panel, cleaned out drain trap, attempted to reset and drain washer, pump did not operate. Removed one wire harness to pump, two hose clamps and slipped pump assembly out of its mounting grommets, and installed new pump in reverse order. A sinch! And saved me approximately
... Read more
$150.00 bucks in repair service fees.
Read less
Was this helpful?
Thank you for voting!
Not Draining - Flashing F-02
12 of 14 people
found this instruction helpful.
-
Andrew from Southampton, MA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
First and foremost, I usually call a real man to come do a job like this, but after reading the repair stories, I gave it a shot. Very, very easy. Pop of the bottom panel off (three torx screws), drain the water out of the tub (if any), and just follow the directions in the box. Anyone can do this one.
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people
found this instruction helpful.
-
Michelle from Richardson, TX
- Really Easy
- Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
shocks showing their age
10 of 10 people
found this instruction helpful.
-
SCOTT from COLCHESTER, CT
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Overall, the install was easy.
Just a matter of getting yourself to get it done.
The video on the removal / install procedures was most helpful.
The front shocks were completed very quickly. The rear shock required all hoses to be disconnected and the back of the washer to be removed. After removing perhaps a dozen screws t ... Read more he cover was still fastened. You will see (in my case) 4 plastic flat clips. after they were removed the back came off. The rest of the project was the same as the front shocks. 1st time thru so to be expected.
Anyway, certainly a project that any DIYer can tackle.
Thanks Partselect for the correct parts in a timely fashion and the knowledge to perform the install.
Scott
Just a matter of getting yourself to get it done.
The video on the removal / install procedures was most helpful.
The front shocks were completed very quickly. The rear shock required all hoses to be disconnected and the back of the washer to be removed. After removing perhaps a dozen screws t ... Read more he cover was still fastened. You will see (in my case) 4 plastic flat clips. after they were removed the back came off. The rest of the project was the same as the front shocks. 1st time thru so to be expected.
Anyway, certainly a project that any DIYer can tackle.
Thanks Partselect for the correct parts in a timely fashion and the knowledge to perform the install.
Scott
Read less
Was this helpful?
Thank you for voting!
baffle had come off of inside drum
10 of 11 people
found this instruction helpful.
-
Salvador from Indio, CA
- Really Easy
- Less than 15 mins
baffle just clicked into place by aligining tabs on baffle with openings on drum. very easy.
Was this helpful?
Thank you for voting!
Displayed F and H alternately
10 of 12 people
found this instruction helpful.
-
LAVERNE from NIANTIC, CT
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Brother who used to sell appliances opened the washer door and read the booklet inside the washer telling him the part necessary to repair the problem. $33/00 for the water flow meter Part and shipped in next morning and arrived overnight. Excellent service for only $7.00 shipping. Highly recommend this place for parts. This was after a
... Read more
couple of days searching the internet for those with the same problem and not receiving and exact part to fix the problem
Read less
Was this helpful?
Thank you for voting!
replace motor
11 of 17 people
found this instruction helpful.
-
David from Eleva, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
Everything went great from order to done. Very happy
Was this helpful?
Thank you for voting!
Broken lock needed replacement
10 of 14 people
found this instruction helpful.
-
Alexander from Miami, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
The best way to do it is not the way I started.
The best way is to 1st remove the bellow's front clamp with a small screwdriver at the spring. 2. unplug the 3 sets of wires attached to the lock. 3. remove the 3 screws on the front that hold the lock. 4. remove the plastic ribbon harness that attaches to the lock. 5. remove the old l ... Read more ock. 6. install the lock back carefully moving aside the cables. 7. install the 3 screws. 8. attach the ribbon harness. 9. attach the cables. 10. replace the bellow. 10. replace the clamp (here you may need someone's help to keep the rubber in place.) 11. the last part to fall in place is where the spring is. 12. If you can't do all by tact then you may want to remove the 3 screws from the top cover to be able to c where all fits.
The best way is to 1st remove the bellow's front clamp with a small screwdriver at the spring. 2. unplug the 3 sets of wires attached to the lock. 3. remove the 3 screws on the front that hold the lock. 4. remove the plastic ribbon harness that attaches to the lock. 5. remove the old l ... Read more ock. 6. install the lock back carefully moving aside the cables. 7. install the 3 screws. 8. attach the ribbon harness. 9. attach the cables. 10. replace the bellow. 10. replace the clamp (here you may need someone's help to keep the rubber in place.) 11. the last part to fall in place is where the spring is. 12. If you can't do all by tact then you may want to remove the 3 screws from the top cover to be able to c where all fits.
Read less
Was this helpful?
Thank you for voting!
error F28 in mid cycle
11 of 17 people
found this instruction helpful.
-
Nicholas from Boothwyn, PA
- Easy
- 1- 2 hours
-
Screw drivers
check error code : no water flow
pulled hoses [hot& cold] to clean screen in line.
pulled flow meter out from under top of hood to clean and check free wheel movement inside.
still error code F28 in mid wash cycle. called in and talk with service: he explained that hot& cold water valve was opening to slow or not enough fo ... Read more r flow meter to read full presure. I replace water valve and flow meter. washer is doing fine. [I was getting readly to go in futher down the line and get new controler. talking to service stop me from spending a lot of money. THANK YOU
pulled hoses [hot& cold] to clean screen in line.
pulled flow meter out from under top of hood to clean and check free wheel movement inside.
still error code F28 in mid wash cycle. called in and talk with service: he explained that hot& cold water valve was opening to slow or not enough fo ... Read more r flow meter to read full presure. I replace water valve and flow meter. washer is doing fine. [I was getting readly to go in futher down the line and get new controler. talking to service stop me from spending a lot of money. THANK YOU
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!