110450 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ripped bellowspul
4 of 5 people
found this instruction helpful.
-
WILLIAM from REPUBLIC, MO
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.
Was this helpful?
Thank you for voting!
Bellow was damaged,water leakage.
5 of 8 people
found this instruction helpful.
-
Gopaul from Queens, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.
Was this helpful?
Thank you for voting!
Spring balanced tub violent shake on spin
4 of 5 people
found this instruction helpful.
-
Paul from TARPON SPGS, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement bro
... Read more
ke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.
Read less
Was this helpful?
Thank you for voting!
Door latch would not lock
4 of 5 people
found this instruction helpful.
-
William from Victorville, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed 2 screws from rear of top that hold top of washer in place, lifted top at the rear and slid it back then lifted it off. Removed the three wiring harnesses from old switch, removed the three screws holding switch in place, theses are accessed from the door opening. removed the two lower screws first and held the switch from the top
... Read more
while removing the last screw. Placed new switch in place and started the top screw by hand followed by hand starting the remaining two screws, tightened screws with phillips screw driver, reconnected the three harnesses, reinstalled the top and secured with the two screws. Door locks and unlocks as it is supposed to.
Read less
Was this helpful?
Thank you for voting!
Leaking water inlet hoses.
4 of 6 people
found this instruction helpful.
-
Helen from NASHUA, NH
- Really Easy
- 30 - 60 mins
Removed the old hoses and screwed on the new hoses.
Was this helpful?
Thank you for voting!
The video supplied by you was great and it worked very well.
3 of 3 people
found this instruction helpful.
-
Michael from NEWBERG, OR
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
It was fast and pretty easy to do.
Was this helpful?
Thank you for voting!
I was getting a sewer smell when the washer drained I did every cleaning technique and didn't solve the problem then I cleaned the inside drain hose and that helped so I replaced the hose and problem solved.
3 of 3 people
found this instruction helpful.
-
anthony from EASTPOINTE, MI
- Very Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.
I replaced the hose and reinstalled the panels and I was do ... Read more ne.
I replaced the hose and reinstalled the panels and I was do ... Read more ne.
Read less
Was this helpful?
Thank you for voting!
Inlet valve was stuck in open position allowing washer to fill with water when not in use.
3 of 3 people
found this instruction helpful.
-
john from YARDLEY, PA
- Really Easy
- 30 - 60 mins
-
Pliers, Socket set
Removed lid. Took old parts off and replaced with new parts. Also replaced hoses while washer was moved away from wall.
Other Parts Used:
Was this helpful?
Thank you for voting!
The inlet valve begins to restrict water flow into the washer based on normal calcium buildup. At a certain point, the washer will start giving an F20 error code indicating it is not getting enough water.
3 of 3 people
found this instruction helpful.
-
Dennis from AUSTIN, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
This is a straightforward replacement. Move the washer to an area where you can work on it. Unplug the washer from the wall. Turn off the water and disconnect the hot and cold water hoses at the washer. Remove the back of the washer. Slide out the top of the washer. Remove the small hose from the valve to the remainder of the washer. Disc
... Read more
onnect the two control wires to the valve. Replace the valve. Replace the small water hose. Reconnect the wires. Replace the top and back of the washer. Connect the water back up. Plug in and try a test load. The water should flow fast enough to reach the back of the machine.
Read less
Was this helpful?
Thank you for voting!
Replace Bellows between door and tub
5 of 9 people
found this instruction helpful.
-
Gerald from Douglas, AL
- Easy
- 30 - 60 mins
-
Screw drivers
Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 ... Read more people
connect bellows to door with spring clip
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 ... Read more people
connect bellows to door with spring clip
Read less
Was this helpful?
Thank you for voting!
One of my baffles just came off during a wash, one of the plastic clps that hold it in place dry rottedafter 10 years
3 of 3 people
found this instruction helpful.
-
scott from DENVER, NC
- Really Easy
- Less than 15 mins
Real easy , the baffle goes in only one way , use the others as guide as too which side the taller end goes.
With one hand pushing in the center of the back of the basket , pushing back , simply place and slide baffle towards you with other hand , there will be a crisp snap as it slide in to place.
With one hand pushing in the center of the back of the basket , pushing back , simply place and slide baffle towards you with other hand , there will be a crisp snap as it slide in to place.
Was this helpful?
Thank you for voting!
Tub filling when power was off due to inlet valve leak.
3 of 3 people
found this instruction helpful.
-
Francisco from DELTONA, FL
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Followed instructions as shown on repair video at site.
Was this helpful?
Thank you for voting!
tub would not turn
3 of 3 people
found this instruction helpful.
-
claude van from big sandy, TN
- Really Easy
- 15 - 30 mins
-
Screw drivers
take the back cover off and put belt on. the belt is a tight fit and requires sone effort, but can be done.
Was this helpful?
Thank you for voting!
Pump not working
4 of 6 people
found this instruction helpful.
-
Darrell from Lady Lake, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Replaced pump
Was this helpful?
Thank you for voting!
door would not latch , and lights on front just flashed
5 of 9 people
found this instruction helpful.
-
FRANCIS from leesburg, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the
... Read more
reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.
Read less
Was this helpful?
Thank you for voting!