11044934201 Kenmore Washer - Instructions

All Instructions for the 11044934201
16 - 30 of 183

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bellow torn on HE3t Kenmore
37 of 55 people found this instruction helpful.
  • Bruce from Tucson, AZ
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
Take off 3 screws at back of top panel and remove. Remove screw to the left of the soap dispenser and push tab on the right inside the machine to remove control panel and lay the panel on top of the machine without disconnecting. Remove 3 screws on the bottom to remove the bottom panel. You have to pull a bit hard to get it off. Remove 3 screws to push through the door lattch and safety switch. Push the window washer nozzle head through the bellow along with the soap feed nozzle.Remove the retainer wire/spring from the bellow where it attaches to the middle panel/inlet. Remove two screws at the top of the middle panel and two screws on the bottom to remove the middle panel with door attached. Loosen the retainer strap ( a large hose clamp) which anchors the bellow to the tub. Remove the plastic nozzle from the window wash hose and mount it in the new bellow. I couldn't get the plastic retainer washer off the nozzle but managed to seat the bello between the washer and the nozzle anyway. Connect the hoze to the nozzle making sure it's pointed in the correct direction. Pull the oblong soap dispenser nozzle into the corresponding bello opening. Seat the bellow around the internal tub opening and place the large hose type clamp, after unthreading it, around the bellow and tighten. Install the middle panel and attach the door latch and safety switch. Now seat the front part of the bellow to the middle panel and attach the retainer hoop/spring. This is a little tricky. I moistened the front rim of the bellow so the hoop would slide over the edge better. You have to stretch the spring to get it to seat properly. Having experience changing bicycle tires helps. Then install the control panel and other panels.
Was this helpful?
Thank you for voting!
The Washer became unbalanced and broke the latch on door
32 of 44 people found this instruction helpful.
  • Glenn from Las Vegaas, NM
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
Had to take the entire front of the washer off to replace the door latch.
Was this helpful?
Thank you for voting!
Water would not drain, motor died
27 of 31 people found this instruction helpful.
  • Michael from Worcester, MA
  • A Bit Difficult
  • 15 - 30 mins
Remove the lower front cover there are three small torx type screw. The pump is the very first thing you see. Have a wet and dry Vac available you will need it. The drain pump and the drain lines contain a lot of water. Unscrew the big white drain plug at the pump and clean up the water, remove the front small mounting screw and disconnec t the two hoses in the back of the pump with pliers and follow the pre-printed steps in reverse. If your machine is more than six years old you will have to use a utility knife and remove a piece of plastic on the electrical connector that is from the washer wiring, if you force the connection on it will brake, look at the connection and the plug and attempt to plug it in before you install the pump. It is easy just be-aware of the connector.
Was this helpful?
Thank you for voting!
belt came off
30 of 43 people found this instruction helpful.
  • wendy from Naples, FL
  • Easy
  • 15 - 30 mins
  • Socket set
Removed back panel,unscrewed the nut on the pulley.Removed pulley and belt. Reassembled.
Was this helpful?
Thank you for voting!
Door would not lock
25 of 29 people found this instruction helpful.
  • Tina from petersburg, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Peel rubber gasket from drum; remove 3 screws using phillip head screwdriver; disconnect wiring e plugs; remove door lock. Install in reverse order.
Was this helpful?
Thank you for voting!
error F 11. Mashine would not run
27 of 36 people found this instruction helpful.
  • Christina from Englewood, FL
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
removed screws on front control panel. found info sheet. read that this part was correct. replaced the motor control unit tho saw no damage on old unit and it works fine now.
Was this helpful?
Thank you for voting!
door lock was broken
31 of 49 people found this instruction helpful.
  • Johnny from Homestead, FL
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
door hook strike was broken half broke in the door the other half stayed in the lock i removed the one pcs from washer with pliers and on the door with a star wrench
Was this helpful?
Thank you for voting!
shaking washer
33 of 57 people found this instruction helpful.
  • Dean from Morrisville, NC
  • Really Easy
  • 15 - 30 mins
  • Pliers
twisted old shock absorbers out and snapped new one inplace...did not really fix my problem though
Was this helpful?
Thank you for voting!
Washer would not spin ( F-02 comes on)
21 of 23 people found this instruction helpful.
  • Steve from Dubuque, IA
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
1-Unplug washer
2-Remove the bottom of the front washer cover 3 screws
3-Locate pump and loosen pump drain cover turn to left just a little enough for water to start draining.
4- Suck-up water with wet/ dry vac. Remove 1 screw holding pump.
5- Flip pump electrical cover up and disconnect wiring from pump.
6- Remo ve 2 hose clamps. The outlet was not to hard to remove, but the intake was not easy to get the pliers on.
7- Install new pump. See instruction to install. I didn't have to remove any ribs to install the connector as in the instruction sheet that came with the new pump. Also I didn't think it was very clear instruction.
8- Last installing the spring clamps. The outlet went okay, but the inlet I never could get on. I could not get the pliers on the clamp. I fooled around at least 20 min. trying to get the clamp on. I went out and bought a 3/4 to 1 3/4 stainless hose clamp with the worm drive design. That is what took so long.You may want to get new hose clamps before starting.
Other wise I did okay.
Was this helpful?
Thank you for voting!
Drum didn't turn/spin
25 of 38 people found this instruction helpful.
  • john from chester, NH
  • Easy
  • 15 - 30 mins
  • Nutdriver, Wrench (Adjustable)
1) Removed back of washer
2) Removed nut holding pulley
3) Pulled pulley off shaft
4) Put new pulley on shaft
5) Replaced and tightened nut
6) Replaced belt on pulley
7) Replaced back panel
7) Washed pile of laundry
Was this helpful?
Thank you for voting!
Washer filling up with water when not in use
19 of 21 people found this instruction helpful.
  • Dominick from Parker, CO
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Very simple repair:
- Turn off water and detach water supply hoses. (Good to have a bucket nearby to catch water left in hoses.)
- Remove 3 screws from the back of the lid; slide lid back 1" and lift off.
- Valve is mounted just under the lid on the back wall of the washer -- remove 1 screw from back of washer that holds v alve assembly in place.
- Remove the 4 electrical connectors (2 black & 2 white) I numbered them with a sharpie so I wouldn't forget how to reattach them. :-)
- Use pliers to squeeze & slide the little hose clamp that holds the internal hose on the valve assembly. Once the clamp is out of the way, pull the hose off the valve assembly.
- Reverse the process to install the new valve assembly.

I ran into a little problem mounting the new valve assembly. The screw hole in the back of the washer did not line up with the mounting hole in the valve assembly. I had to drill a 3/16" hole just to the right of the original screw hole on the back of the washer. Used the new hole to mount the valve assembly, done.
Was this helpful?
Thank you for voting!
would not spin of agitate
20 of 28 people found this instruction helpful.
  • Doug from Hartselle, AL
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
I first had to take off the back and the top to get to the pulley and the belt. The pulley had woobled so much that it had worn out the center nad it would no longer hold to the post in the tub. It also had cut into the back of the tub about a 1/4 to 1/2 inch. I unscrewed the nut holding the pulley and removed it. I then took a knife and trimmed the rough edges off the back of the tub to make it smooth. I then smoothed out the end of the post that the pulley fits on so the new pulley would fit. I tightned the nut and put the belt on the motor drive shaft and Used a robo grip to hold the belt as I turned it onto the pulley. I but the back and top back on and that was it.
Was this helpful?
Thank you for voting!
FH code-4 minutes into cycle
17 of 19 people found this instruction helpful.
  • robert from LITLE RIVER, SC
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
remove 3 screws of top panel at rear. slide top to rear 1/2 inch and lift up. disconnect wire to flometer, remove clamps on hoses and remove, reverse to install. did not fix problem. ck'd screens at fill valves. ordered new fill valves--problem solved. solenoids must not have been opening up all the way.
Was this helpful?
Thank you for voting!
Motor Control Board faulted.
21 of 32 people found this instruction helpful.
  • Brent from Normandy Park, WA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
I read the instructions once and then started. It was easy but did take an hour to do the entire job.
Was this helpful?
Thank you for voting!
leak suddenly developed
16 of 18 people found this instruction helpful.
  • Gerald from Troy, NY
  • Really Easy
  • 15 - 30 mins
  • Pliers
Somehow a bobby pin got into the drain pump housing. When it started to drain, the pin was rammed through the housing.Extremely easy to remove and replace. No special skills needed. Whirlpool did a good job in making it idiot proof. Unpacking the part took longer than installing it. Don't be afraid to do this repair. If you own a pair of pliers and a screwdriver,you can do it.
Was this helpful?
Thank you for voting!
All Instructions for the 11044934201
16 - 30 of 183