11042 Kenmore Washer - Instructions

All Instructions for the 11042
121 - 135 of 255

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Error codes SUD and Fo2
2 of 2 people found this instruction helpful.
  • Gregory from LEXINGTON, SC
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump w ith the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good
Was this helpful?
Thank you for voting!
Tub would get out of balance on the spin cycle
2 of 2 people found this instruction helpful.
  • Kirk from P C BEACH, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
UNPLUG WASHER ,SLIDE WASHER OUT FROM THE WALL. TAKE THE BACK OFF ,THEN TAKE PANET OFF IN THE FRONT. TWIST OLD SHOCKS ON THE TOP FIRST THEN TWIST BOTTOMS AND THE SHOCK WILL CUM OUT. PUT NEW SHOCK IN BOTTOM FIRST TWIST TILL YOU HEAR OR FEEL THE SHOCK SEAT ITSELF THEN INSTALL ON THE BOTOOM OF THE TUB.
Was this helpful?
Thank you for voting!
Replace tub to pimp hose.
2 of 2 people found this instruction helpful.
  • Bob from LORAIN, OH
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.
Was this helpful?
Thank you for voting!
Washer had a 'thunk' sound during washing. I removed the back and saw the broken shock.
2 of 2 people found this instruction helpful.
  • Jeffrey from Bothell, WA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
1. After ordering I watched the video on the page for the part, the guy showed exactly what to do.
2. The day the part was to arrive I leaned the washer back and opened the lower front, based on the video on the page for the part, and removed the old shock absorber.
3. Part arrived, and I put in the new shock.
4. I ran a li ght load in the washer and it worked.
5. I put the washer back together and put in place.
6. I have since run a full load and it has worked well.

Note: In case I messed up the shock I was putting in, I bought 2 but did not need the 2nd one. I have kept it, just in case my 20 year old Whirlpool might need another one in the future.
Was this helpful?
Thank you for voting!
Replacing the heat sensor following an F-24 Error Notice.
2 of 2 people found this instruction helpful.
  • william from VIRGINIA BCH, VA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
Was this helpful?
Thank you for voting!
Bellow pierced
4 of 8 people found this instruction helpful.
  • Alexander from Miami, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
1. Remove bottom panel (3 screws below). 2. Remove top panel (3 screws back). 3. Remove detergent dispenser (remove T screw in front.) 4. Carefully remove control panel is plastic so be careful not to break it. 5. Pull broken bellow from front and spring loaded clamp will come lose. 6. Push away bellow. 7. Remove cables from door lock. 8. Remove front panel screws (4 - 2 on top and 2 in bottom). 9. Unscrew bellow's clamp with flat screw driver or not driver. 10. Remove worn bellow. 11. Bellow has notch on top (Use as reference to replace. 11. Clean all surfaces. 12. Install new bellow to drum. 13. Screw clamp over of bellow not too tight. Don't want to break the seat. 14. Replace all in the reverse order and for the front of the bellow refer to my previous article (story) on front latch replacement.
Was this helpful?
Thank you for voting!
Bellow leaking water
3 of 5 people found this instruction helpful.
  • Eric from Vacaville, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.
Was this helpful?
Thank you for voting!
Tear in door seal
4 of 9 people found this instruction helpful.
  • sean from Palm Coast, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
First I removed the retainer ring that holds the outside bellows on the frame of the front washer.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clam p. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.
Was this helpful?
Thank you for voting!
front door leaking
3 of 6 people found this instruction helpful.
  • jim from winchester, VA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
2 clamps and its off, problem is if you have average size hands you will struggle in getting the back clamp on and off.
Was this helpful?
Thank you for voting!
Water leaking past shut off valve (solenoid operated)
2 of 3 people found this instruction helpful.
  • Anwar from Pleasanton, CA
  • Easy
  • 30 - 60 mins
  • Wrench (Adjustable)
Inputs on your web site of other people who had replaced this valve assembly helped.
Remove top cover from washer - three socket head screws on rear of machine, (need to move washer forward for access)
Turn off both hot and cold manual shutoff vales on wall. Run washer to take water pressure off from hoses (turn on for water to turn on , and then turn washer off).
Remove both hoses (mark/remember which side is hot/cold, as valve assembly has no markings), from valve assembly, had to use channel locks/adjustable wrench to remove nuts as they were really tight. Check to see if gaskets were OK, would have been nice, if these gaskets are supplied with new valve assembly. Remove screw which holds valve assembly to washer. Slide valve assembly slightly side ways to free it from bulkhead panel. Remove last hose assembly inside washer, attached to valve; remove four wires from solenoids. Keep track of wires (which solenoid).
Replace valve, reconnect internal hoses and wires; install valve assemble on bulkhead panel; attach screw; reconnect hoses; turn on manual valves; check for leaks; briefly turn on washer, check for internal leaks; install cover; push back washer in place.
Was this helpful?
Thank you for voting!
tub filling with water when not in use
3 of 6 people found this instruction helpful.
  • Robert from Thornton, CO
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I had units stacked so I had to take the dryer off, pull 3 screws from back, slide cover back and the water valve is right there, easy to change. I have not had the problem since then.
Was this helpful?
Thank you for voting!
Water flooding from under the washer
2 of 3 people found this instruction helpful.
  • Linda from WEST BABYLON, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Remive 3 screws along bottom front panel and remove that by pulling down and off. Remove 4 screws from the back of washer along the top to remove top cover. Pull out dispenser tray. Remove 2 screws from along dispenser, then carefully remove the control panel by inserting a screwdriver to release internal clips along the top. Put the cont rol panel on top of the washer. This gives you access to 2 more screws at the top, and also 2 screws on the bottom, that will release the door panel. You'll have to disconnect 3 wire connections to get access to the wide rubber gasket (bellow). There is an inner ring and an outer ring holding it in place. The outer ring is a spring. Pull that off. Then remove the inner by loosening the screw holding the clamp. Pull the bellow off and replace with the new one. Make sure the gasket goes completely over the large water spout and the smaller button sprayer at the top taking caution to have the gasket sit between the two plastic washers attached to it. Make sure the belllow is firmly seated inside and out before attaching the bellow. Reattach everything in reverse order. Problems you'll run into: getting the spring on the outer gasket as it is tight to get on and the rubber will keep slipping off the edge where it is seated. Also, you may need an extra pair of hands to hold the door up while you attach those wire connections as there is no play in the wires.
Was this helpful?
Thank you for voting!
The dryer nob wasn't working the dryer knob broke off inside the unit
2 of 3 people found this instruction helpful.
  • WILLIAM from SEBASTIAN, FL
  • Very Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him
Was this helpful?
Thank you for voting!
All 3 baffles had broken
4 of 9 people found this instruction helpful.
  • Jennifer from Christiansburg, VA
  • Very Difficult
  • More than 2 hours
  • Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Repair was described as a simple 5 minute job following the enclosed directions. There were no directions included. Customer service replied they could not provide any instructions. I located a technical manual online and determined the steps necessary to replace the baffles. While some may just click them in, a proper repair requires the control pannel and machine housing to be removed. Then the tub assembly must be removed and the plastic tub separated from the basket. Three screws (one for each baffle must be installed. (I recommend using blue loctite to keep the screws from backing out). The entire process must then be reversed. This is a slightly complicated (note the pencil is to mark the locations of clips for ease of reinstallation. I am an Engineer and this process took over 2 hours and required a significant amount of space to lay out the parts as the machine was totally disassembled. This assembly is best accomplished with 2 people and an entire afternoon without interruption. It can be done by anyone with some mechanical skills, but find the consumer services technical manual first and be prepared to keep track of a lot of small and large parts. This is not the simple 5 minute job described by others (unless you just want to snap the baffles on the basket and not lock them down). In that case go ahead and order a few more sets as the clips will break and the baffles will slide off and you will be replacing them about every 6 months.
Was this helpful?
Thank you for voting!
machine wouldn't turn on when lid closed
2 of 3 people found this instruction helpful.
  • Ellen from NYACK, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
replaced missing screw and pad and now machine works perfectly
Was this helpful?
Thank you for voting!
All Instructions for the 11042
121 - 135 of 255