110419 Kenmore Washer - Instructions

turned off water to mach. removed the top off the mach. with scket, removed old valve and replaced it with the new one, very easy.

Replace water pump

Very easy. Revived back of washer. Used a screwdriver to pull belt over pulley. Very easy

Well first of all when you buy this washer, the salesperson should tell you about checking the drain catch (ahead of the pump) and emptying out whatever get's caught in there. Never had a clue until it wouldn't work, then did a search on the internet, and darn if I didn't find specific instructions on how to open and clean out. Mine was p ... Read more acked full of hair pins, small change, lint, buttons, etc, all kinds of stuff. Guessing that is why the pump went out in the first place, it was so packed full that the pump could not draw any water through. But even after I cleaned it out, the pump was already shot. So called a service man, he said the pump would cost me around $200, then his labor to put it in, plus a $68 service call to just come and look at it, and $68 when he comes back to replace it. So I searched the internet for how to replace, came up with a very detailed You Tube video on how to replace Whirlpool Duet Pump. So ordered my pump from PartsSelect, just over $100, and replaced it myself. Super easy, only about 5 minutes. Thanks! —A very determined housewife!

open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.

We purchased a new pump and installed it very easily. My washer works great!

Just use the video. Shows you all you need to know. Very easy. Do it yourself and it saves you money.

other than needing a new type of screw driver (not philips or flat head, but rather a starfish looking thing), the replacement was simple. took 5 minutes (after finding the correct driver)

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

I was already very familiar with the motor & drain pump, as I had disassembled my original one in attempt to find the problem & fix it. Finally, I broke down & purchased a new one. It was VERY easy to install! The most difficulty was finding the right sized board to put underneath & raise the machine up (with the dryer attached to the ... Read more top of it) to place the board underneath so that I could tighten the bolts from underneath to attach the pump. After that was over, the rest was cake! Just attach the hoses & the electrical, which just clips in place & my washer is like new again! Yay! Oh, and yes, I'm a woman DIY'er.

I used the video at parts select as a review, then just followed it. Easy de-install, reminder there's water in the line be prepared with a pot or vase to hold the water. Easy install. Washer runs perfect now. As quiet as when we bought it. I always try to fix before I re-buy, not a big green guy but I try to keep stuff working and out of ... Read more land fills. Also the part was at my door in 1 day, Awsome!.

After unplugging the washer, the unit was pulled forward and tipped backwards, I placed a 2x4 under the washer to serve as a brace. I removed the existing bolts holding the old pump in place, removed the spring hose clams, unplugged the pump and removed the damaged part. inserted the new drain pump, re-inserted the bolts and tightened ... Read more them, replaced the spring clamps with "regular" hose clamps supplied with the replacement part, plugged in the power supply, removed the brace, pushed back the unit and plugged it into the outlet. From start to finish - about 20 minutes. Was running wash about a half hour after I started.

Very --simple remove front acess panel -- open sump clean out remove water out of existing pump an hoses with small wet dry vac -- remove small wire harnes --cut band clamp on discharge with side cutter --remove inlet -suction side of pump hose clamp with channel locks --un bolt two screws on bottom side of washer with 5/16 nut runner --d ... Read more iscard old pump reinstall new one in reverse order --only takes about 20 mins total !!! ---

I watched the video and it really was as easy as it looks. Great shipping time, I ordered the pump Monday and it arrived on Thursday, standard ground shipping!

Followed instructions from a You Tube video. I'd recently lost my job and money is tight and I thought we could save money doing it myself. By watching the video and ordering parts from you we were able to save $500 between parts and labor. Thanks