110419 Kenmore Washer - Instructions

unhooked two water lines & electrical plugin unbolted old pump and installed new pump. took about 15 minutes.

Unhooked two hose clamps took two screws off put new aprt on hooked back up works great

Unplug machine from electrical outlet.
All screws can be removed with a 1/4" socket, either with a socket wrench or nut driver.
Top panel - remove three screws on back, slide panel back an inch or so, and lift off.
The control panel must be carefully pulled off by using a screwdriver to pry it away, and then placed on top ... Read more of machine. Be careful not to disconnect or damage any attached wires.
Pull out the detergent dispense drawer, press the retainer on the left rear of dispenser drawer, and pull it out and set it aside. One small torx screw must removed from the dispenser housing.
Bottom front panel - remove three screws to take it off. This exposes the screws on the front panel.
The front panel of machine must be removed as well.
This is the most tedious part of the job, as the door seal must be disconnected from the panel. Remove the wire and spring retainer around the door that holds seal in place. The spring portion of the retainer is on the bottom of the opening. Pry it off with a screwdriver, being careful not to damage the rubber seal. Do not remove it, simply push it into the washer opening.
Remove the screws from the front panel - two on top, and two bottom. It has some wires on the right side, and to avoid damaging them, support the panel with a stool and prop it up against the machine.
You can now access the hose on the rear bottom of the dispenser. Using a pliers, squeeze the retainer and pull the hose off the dispense. The other end is pressed into the tub - simply pull it out. I recommend cleaning the edges of hole to assure a good seal when installing the replacement.
To install the replacement hose, press it into the tub, making sure to get the channel in the hose properly inserted in order to make a solid seal. Attach the other end to the dispenser with the retainer.
Reassemble by reversing the order described above.

removed bottom panel and took out pump and replaced it with new one

My husband removed the bottom panel of the washer and removed the old pump with two screws, then removed the water hose coming into the pump and unplugged the electrical push in type plug from the side of the pump. Simple reversed the process to instal the new one and replaced the front panel. Simple really...far more so than calling a re ... Read more pair man.

My husband and son removed the old pump and replaced it with the new pump assembly. The whole process took about 30 minutes max.

Remove two star screws. Remove broken striker. Installed new striker. Took two mins.

The washing machine would only run on the hot water cycle. When trying to use the warm or cold setting, the water would dribble into the drum and result in an LF error code(long fill). I watched a brief video on replacing the water inlet valve which made it really easy to repair. I first turned off the water, disconnected the hoses from t ... Read more he machine, and opened the top to access the valves. I then disconnected the wires from the valve, removed the water tubes, swapped out the valves and put everything back together. I am not experienced in repair but this was a very easy fix! We decided to replace the single hot water valve and the dual cold water valve since it's an older machine and it works like new again!

The most time consuming part was fitting the hose back on because of the confined space. Once on the rest was a snap. The drain pump installed just the same as the video, so watch the video! I think in total it took about 30 minutes to complete.

Easy fix,
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will m ... Read more ake it lot easier.
Good luck on your repair

replaced the hot water valve

Couldn’t see exactly where it was coming from. Checked the bellow and it looked ok. Took this hose off and it was kinda chewed up a bit where it connects to the tub. Not bad but enough to make it leak. Ordered the new one. Took forever to get here thru fed ex smart post. Repair takes longer to get the panels off than it does to put ... Read more new hose on. Hope this helps someone out there.

I just took off the old part and installed the new one. The new part was a bit different.

Remove old belt, rotate large washer belt wheel, guiding belt off large wheel.
Guide new belt onto Washer Large Wheel. Use a pair of pliers to hold belt onto wheel as one turns the large washer belt wheel, guiding belt onto wheel. Note belt will be tight. Seems like belt will not fix but keep going it will fit, you might even hear it ... Read more pop on.
Old Part number (W10116215) new replacement Part number (W10388418).
New replacement washer belt fits tight, that is ok.

just changed out the pump. easy