110296 Kenmore Washer - Instructions

All Instructions for the 110296
91 - 105 of 2137

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
bad lid swithch, problem with spin cycle
22 of 32 people found this instruction helpful.
  • Bill from Beaver Dam, KY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
remove 2 screws that hold timer section
remove large clips that hold lid section
repace lid swich and put back together
works good
Was this helpful?
Thank you for voting!
washer wouldn't start up after filling & closing lid
20 of 26 people found this instruction helpful.
  • Jeremy from Marengo, IA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
First I loosened the 2 screws on the outside of the top control assembly with a philips screwdriver. Then I took out the 2 other screws toward the top on the back with a socketwrench.Next I removed the top so I could access the switch. After that I removed the broken switch and unhooked from wire hareness. I then hooked up the new switch and snapped into place. Last I put the top back on and screwed into place.
Was this helpful?
Thank you for voting!
Lid Switch Asembly broke
19 of 23 people found this instruction helpful.
  • Brooks from Plano, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First off I would highly recommend the review by Dennis From Evans City PA. This was quite helpful.

The problem is the lid switch assembly is glued together and the original part came apart and needed to be replaced. The symptoms described by others were accurate so we opted to replace it.

On my machine there are tw o screw on the front corners of the panel where the dials attach to the top of the washing machine. I removed those two screws and by lifting up and forward was able to move the whole thing out of the way.

You should see the connection from the dial panel running down into the wash basin. This is where you will unplug the old switch and replace it with a new one. There are little plastic clips that hold it in place, but you can squeeze them with your fingers to remove it from the panel.

In order to get access to the underside where the wires are connected you will need to remove two clips that hold the back pane to the rest of the sheet metal. In my case I wasn't quite prepared for the entire frame to move but once the clips are removed the back panel is completely removed and you can pull it forward to gain access to the underside.

Once you are able to get underneath you will see a screw that holds the ground wire. This is the one that you may need pliers to remove. There are two screws that hold the switch in place but you can access them at any time. I had already removed the old screws by this point. This should leave the switch disconnected from everything and you can install the new one.

Now just connect everything back together. The two screws for switch where the lid hits. Connect the ground wire and run the the connection back to the top portion where it will connect back up to the top panel.

I would add that there are two thin plastic strips that ran vertically up the back fo the back panel that meet the outer casing. I had to re-seat these before putting the clips back on the top.
Was this helpful?
Thank you for voting!
Agitator did not rotate properly
18 of 21 people found this instruction helpful.
  • Tenel from The Woodlands, TX
  • Easy
  • 30 - 60 mins
  • Pliers, Socket set
1. Removed the softener dispenser
2. Removed the cap covering the clutch dogs and the bolt holding it all in place.
3. Removed the bolt holding the two agitator pieces and the clutch dogs together.
4. Removed the two agitator parts.
5. Replaced the clutch dogs.
6. Reassembled and put the bolt back in place.< br />7. Replaced the gasket on the cover that goes over the clutch and bolt.
8. Replaced the softener dispenser

Very easy!
Was this helpful?
Thank you for voting!
Top Half of Agitator would not function without appying sideways pressure
18 of 21 people found this instruction helpful.
  • Donald from Fredericksburg, VA
  • Really Easy
  • 15 - 30 mins
  • Socket set
Heard about the website... 1 minute to find it, 10 minutes to order new cogs... 3 day wait for new parts... Rec'd Fedex, 15 minutes total to pull the agitator cover (bleach dispenser) then the bung cover with o-ring (just lift out) expose bolt, unskrew and remove top portion of agitator or entire agitator if it's easier. Seperate, remo ve black cog holder (slides up the spindle) and replace cogs one at a time just like the old ones. Reassemble in reverse and you are back in business. Saved the $75 deductible on my home appliance warrenty. You guys are the best... cheers...
Was this helpful?
Thank you for voting!
Agitator was barely agitating. Making a clicking noise.
17 of 18 people found this instruction helpful.
  • Charmaine from Slidell, LA
  • Easy
  • 15 - 30 mins
  • Socket set
Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.
Was this helpful?
Thank you for voting!
Would not spin
24 of 40 people found this instruction helpful.
  • floyd from Slidell, LA
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.
Was this helpful?
Thank you for voting!
The washer did not spin fast enough during the rinse cycle to adequately dry the load of clothes
17 of 19 people found this instruction helpful.
  • Richard from EL SEGUNDO, CA
  • A Bit Difficult
  • More than 2 hours
  • Socket set
I repaired my Kenmore washing machine replacing the clutch, Motor coupling and cogs. All of the parts came quickly and with good instructions. Best of all there were links to youtube repair walkthroughs. With out these step by step instructions this project would have taken much longer. Now the washer is like new! WATCH THE YOUTUBE PAUSE DO THE STEP AND REPEAT
Was this helpful?
Thank you for voting!
The movers broke both water intakes off flush with the back of the machine
16 of 17 people found this instruction helpful.
  • Dennis from Oak Island, NC
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.
Was this helpful?
Thank you for voting!
Automatic water temperature switch failed
22 of 35 people found this instruction helpful.
  • stephen from Coventry, RI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
removed two screws and atc knob. swung control panel out. unplugged atc switch. pushed little tab down and turned the switch. it popped out and I put the new one in. plugged the cable back in. repositioned the control panel. replaced the atc knob and turned it to rinse. Voila!!! it works.
Was this helpful?
Thank you for voting!
Somehow or another, the plastic cup inside vanished.
17 of 21 people found this instruction helpful.
  • Warren from Lakewood, CO
  • Really Easy
  • Less than 15 mins
This was a really easy replacement job. All I had to do was twist the old Fabric Softener Dispenser to the left to unlock it, pull it off, and put the replacement on.
Was this helpful?
Thank you for voting!
Water was leaking at the pump
17 of 21 people found this instruction helpful.
  • Paul from Painesville, OH
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.
Was this helpful?
Thank you for voting!
Cold water flow was slow
22 of 36 people found this instruction helpful.
  • Garry from Palm Bay, FL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Removed old part; exchanged rubber plungers between the hot and cold. Symptoms still the same - so eliminated the need for new rubber plungers (even though they still needed to be replaced). The only item left were the magnetic switches opening and closing the flows. The syphon was replaced due to broken plastic mountings causing the syph on to hang into the drum. Repair was a snap and finding the parts on your site was very easy and parts were there within 2 days at standard shipping. Thank you.
Was this helpful?
Thank you for voting!
Leaking drain hose
16 of 19 people found this instruction helpful.
  • Steve from Cypress, CA
  • Really Easy
  • Less than 15 mins
  • Pliers
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.
Was this helpful?
Thank you for voting!
Washing machine leaking water
16 of 19 people found this instruction helpful.
  • John from Oklahoma City, OK
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconne cted hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!
Was this helpful?
Thank you for voting!
All Instructions for the 110296
91 - 105 of 2137