110277 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Electrical burning smell washer stoped working
11 of 19 people
found this instruction helpful.
-
Arthur from Statesville, NC
- Really Easy
- 30 - 60 mins
-
Screw drivers
Replaced motor starting capacitor. Noticed water leak at pump and replaced pump
Other Parts Used:
Was this helpful?
Thank you for voting!
Water Pump was leaking
9 of 13 people
found this instruction helpful.
-
Rick from Liberty, SC
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.
I turned the washer on its side and felt where the leak was on th ... Read more e pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.
I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!
I turned the washer on its side and felt where the leak was on th ... Read more e pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.
I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
washer would fill but not run
10 of 16 people
found this instruction helpful.
-
steve from madison, SD
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
After reading other comments about lid switch replacement , I knew the front of the control panel would move forward and lift off. Although none of the descriptions mention the steel clips that were also use to hold the cover down. It does take quite a bit of presure to pry these up and loose before panel would move forward. Would recom
... Read more
end putting tape on both washer and screwdriver to protect washer.
Read less
Was this helpful?
Thank you for voting!
Ground prong on power cord was broken
10 of 17 people
found this instruction helpful.
-
RONALD from PORT ORCHARD, WA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Disconnected old power cord inside control cabinet, removed strain relief , then removed damaged power cord. Reinstalled new cord with new strain relief.
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken Fabric Softener Dispenser
8 of 11 people
found this instruction helpful.
-
JOAN from Little Elm, TX
- Really Easy
- Less than 15 mins
Just removed the broken part and replace it with the new one.
Was this helpful?
Thank you for voting!
Agitator not working
7 of 8 people
found this instruction helpful.
-
kevin from oxford, PA
- Really Easy
- Less than 15 mins
-
Wrench set
Removed cap, used a wrench to remove nut for agitator, put new one in place put nut back on and the cap back on and started washing clothes easy fix saved me $300.00 Thank you
Was this helpful?
Thank you for voting!
Fabric Softener dispenser was broken
7 of 8 people
found this instruction helpful.
-
Steve from Lufkin, TX
- Really Easy
- Less than 15 mins
Replacing the fabric softener dispenser was very easy. It just snaps on. Make sure you line up the tabs with the holes in the agitator, otherwise it will not stay on and will fly off and break in the spin-cycle. This is how the first one broke to begin with.
Was this helpful?
Thank you for voting!
top agitator would not operate
8 of 11 people
found this instruction helpful.
-
Larry from Edgewood, TX
- Really Easy
- Less than 15 mins
-
Socket set
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.
Was this helpful?
Thank you for voting!
Water level selector inoperable, washer stuck in "Med" load.
6 of 6 people
found this instruction helpful.
-
Anthony from MIDDLETOWN, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Using the guidance listed on your website for part #PS3408149, Water Level Pressure Switch, I removed two screws on each side of the rear Control Panel, removed the dial from the front, lifted the panel on the right side from rear, removed the hose and the electrical plug, twisted off the broken part and installed the new one in abs
... Read more
olute reverse! Reassembled panel, plugged in unit to electric and performed function check to great satisfaction! (by doing one med load and one super load over next 2 hours)
Read less
Was this helpful?
Thank you for voting!
Washer not completing rinse cycle. Broken centrifugal switch
6 of 6 people
found this instruction helpful.
-
Rudolph from LAUDERHILL, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I disconnect power from wall outlets. Turn off pipes and remove water hoses from machine. Clear machine making room to operate.
I removed two Phillip head screws from behind the console, press down lightly on console then flipped it back. Disconnect the lid switch by releasing the plastic clip. Used a screwdriver to release the 2 met ... Read more al holding clips (one on each side on top of machine. Ease the case up slightly then pull back gaining access to the centrifugal switch which is mounted to the motor with one Phillip head screw. One end of switch was broken and disconnected. Motor was not keeping up. Discharged capacitor by grounding the terminals with an insulated plyers. Lift the clip on the broken switch then pull the connector off. With new switch in hand, remove each of the 5 wires from the old switch by using a needle nose pliers one by one and connect them to the new switch making sure each one is properly secured in please. Connect the new switch to the motor using the single screw. Secure the connector to switch. Replace case by tilting back about 45 degrees, slide under front frame of machine all the way then down inplace. Use the two metal clips to secure frame to rear panel. Reconnect lid switch. Return machine to usual spot, reconnect water hoses, turn pipes on make sure there are no leaks. Plug back into wall outlet. Washer was tried and all cycles were completed.
I removed two Phillip head screws from behind the console, press down lightly on console then flipped it back. Disconnect the lid switch by releasing the plastic clip. Used a screwdriver to release the 2 met ... Read more al holding clips (one on each side on top of machine. Ease the case up slightly then pull back gaining access to the centrifugal switch which is mounted to the motor with one Phillip head screw. One end of switch was broken and disconnected. Motor was not keeping up. Discharged capacitor by grounding the terminals with an insulated plyers. Lift the clip on the broken switch then pull the connector off. With new switch in hand, remove each of the 5 wires from the old switch by using a needle nose pliers one by one and connect them to the new switch making sure each one is properly secured in please. Connect the new switch to the motor using the single screw. Secure the connector to switch. Replace case by tilting back about 45 degrees, slide under front frame of machine all the way then down inplace. Use the two metal clips to secure frame to rear panel. Reconnect lid switch. Return machine to usual spot, reconnect water hoses, turn pipes on make sure there are no leaks. Plug back into wall outlet. Washer was tried and all cycles were completed.
Read less
Was this helpful?
Thank you for voting!
washer would walk all over when in the spin cycle
6 of 6 people
found this instruction helpful.
-
Chris from Bonners Ferry, ID
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
I tried to remove the outer console to get to the tub wear pads easier. This proved difficult for me for some reason. So I tipped the machine on its back at about a 45 degree angle. You will see the tripod support holding up the tub. The pads lie in between the bottom of the tub and on top of the tripod support . You won't be able to
... Read more
see the pads since the are on the top of the support, but you will see the two insert tabs of each pad sticking out. There are about 120 degrees apart from each other. I pushed up on the tub and slipped the piece of wood in between the tub and tripod support close to the pad. Taking a screwdriver and hammer I punched out the wear pad insert tabs. You can replace the old pad with the new one by using some force with your hands. Some pop right in and some you need to use a little leverage, maybe with the piece of wood you used to hold up the tub. Be careful not to get the pads greasy, keep clean as possible. Worked great.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer was not filling with water to proper level (was filling some, not enough)
8 of 12 people
found this instruction helpful.
-
Chris from LIBERTY TWP, OH
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Ordered part PS3408149 from partselect.com. Lifted Washer control panel with putty knife. Removed hinges (regular screwdriver, used as a crowbar rather than screwdriver) holding control panel to washer body. Moved washer body panel out of the way, and reviewed level sensor/level selector switch. Take handle off front of selector switc
... Read more
h. Twist selector switch off from inside (90 degree turn till square inset lines up withsquare hole, then it will come out). Insert new selector switch. Remove old tubing. Fish new tubing through where old tubing was. Cut off extra tubing, then push tubing onto selector switch and tub basin (where old tubing was). Put washer back together. Done. Worked perfectly.
Read less
Was this helpful?
Thank you for voting!
My husband did it. He popped the top control section off by sliding the knife under each side to lift it off.
6 of 6 people
found this instruction helpful.
-
Anne from IRA, MI
- Very Easy
- 15 - 30 mins
The switch just snapped out of the holding section and the new part was snapped back into its place. He put the top section back on and it worked! Being a woman not knowing anything about repairing machines, I thought it went very well. I just googled my problem with the washer, it sent me to this site saying what they thought was the pro
... Read more
blem, I live chatted with someone and they confirmed the solution. I ordered the part and it came in 2 days and my husband fixed it. And now I have a working washer again. Thank you for your site. Anne
Read less
Was this helpful?
Thank you for voting!
Washer would not work in agitate or spin cycle
6 of 6 people
found this instruction helpful.
-
yesenia from apopka, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off wit
... Read more
hout unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.
The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.
It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.
The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.
It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.
Read less
Was this helpful?
Thank you for voting!
washer wouldn't spin with load, then not at all with rapid clicking sound
6 of 6 people
found this instruction helpful.
-
Lou from ATLANTIC HLDS, NJ
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Clutch was noticibly worn compared to new part. Direct drive flange had broken, this part should be steel. found a you tube video that was simple to follow. no problems
Other Parts Used:
Was this helpful?
Thank you for voting!