110272 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
I bought a used washer from a friend and they had cut the drain hose short .
25 of 38 people
found this instruction helpful.
-
Francis from Yuba City, CA
- Really Easy
- 30 - 60 mins
-
Pliers
I got a pair of channel lock pliers and took off clamp on the hose, after laying wash machine on it's side, poped off a few little clips and replaced the hose, and now everything works perfect.
Was this helpful?
Thank you for voting!
Although the motor was running, washer wouldn't agitate or spin.
20 of 24 people
found this instruction helpful.
-
Thomas from Commack, NY
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set, Wrench set
After disconnecting the electrical supply, first remove the two screws at either end of the control panel and fold it back away from the washer top. Then, unplug the electrical lid switch connection. Now, remove the two clips at either end on top to disconnect the housing from the washer back and chassis. The motor is sandwiched betwee
... Read more
n the water pump in the front and transmission at the rear. The Direct Drive Coupling connects the rear motor shaft to the transmisson. After you have taken the outter portion of the washer off, remove the two snap clips that hold the water pump in place and slide the pump off the front shaft. Best to also disconnect the upper hose connection so the pump can be moved out of the way. Caution though, remaining water in tub will drain out. Now remove the two screws that hold the clips in place which secure the motor to the transmission. Careful, as the old Direct Drive Coupling is probably destroyed, the clips are the only thing holding the motor in place and the motor needs to be supported so it won't drop to floor when the clips are removed. Be careful not to lose the four rubber grommets which sit between the motor and transmission bracket. After motor is on floor remove the old plastic slip-on direct drive coupling discs from both the motor and transmission shafts. The new replacement discs have steel centers which do not slide onto the shafts as easily as the old plastic ones did. I had to tap the center steel portion onto the shafts using a hammer and a deep wall socket the same width as the steel portion of the disc. Be careful! I'm sure that tapping the plastic portion of the disc to properly seat it on the shaft will break it away from the steel portion. In my case, It took me several attempts to completely seat the new discs. I had to do quite a bit of tapping to get the discs seated far enough onto the shafts so that the motor slipped easily against the transmission bracket grommets and the retainer clips snapped back into place easily. Reassembly is simply reversing the steps you took when taking the unit apart. Before putting the outter housing back in place, I checked to make sure everything was running smoothly by jumping out the electrical snap-in connection for the lid switch and running the machine in the spin cycle. Remember, if you don't jump out the lid switch and just try to test the unit in the aggitate cycle, the machine has to first fill with water.
Read less
Was this helpful?
Thank you for voting!
stopped working only filled with water.
20 of 24 people
found this instruction helpful.
-
Christa J from ElDorado Springs, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
Fast simple and supper easy! Please do not waist your time or money on repairmen that rip you off. You are garunteed all the way or your money back from Parts Select. Go to your model number than read a few stories of others to better pin point your problem then order part and your item will ship fast I had my part on the 2nd day of the
... Read more
order. Do not be fooled you can do it easily! I have order twice and both items went smoothly and took less then 10 minutes to put in. Thanks Parts Select for making it possible for the little guys and supporting them and not the big rip off scammers. I will be back when needed. May you continue in your good deed! C.S.
Read less
Was this helpful?
Thank you for voting!
washer did not agitate
21 of 28 people
found this instruction helpful.
-
Eric from Jacksonville, FL
- Really Easy
- Less than 15 mins
-
Socket set
popped thecap off removed the bolt, pulled agitator off replaced cogs(dogs) then put back together. works like new.whole time took about 10-15 min. saved my self 150.00 by not hireing repair man.
Other Parts Used:
Was this helpful?
Thank you for voting!
washer wouldn't start up after filling & closing lid
20 of 26 people
found this instruction helpful.
-
Jeremy from Marengo, IA
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
First I loosened the 2 screws on the outside of the top control assembly with a philips screwdriver. Then I took out the 2 other screws toward the top on the back with a socketwrench.Next I removed the top so I could access the switch. After that I removed the broken switch and unhooked from wire hareness. I then hooked up the new switch
... Read more
and snapped into place. Last I put the top back on and screwed into place.
Read less
Was this helpful?
Thank you for voting!
bad lid swithch, problem with spin cycle
22 of 32 people
found this instruction helpful.
-
Bill from Beaver Dam, KY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
remove 2 screws that hold timer section
remove large clips that hold lid section
repace lid swich and put back together
works good
remove large clips that hold lid section
repace lid swich and put back together
works good
Was this helpful?
Thank you for voting!
Lid Switch Asembly broke
19 of 23 people
found this instruction helpful.
-
Brooks from Plano, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First off I would highly recommend the review by Dennis From Evans City PA. This was quite helpful.
The problem is the lid switch assembly is glued together and the original part came apart and needed to be replaced. The symptoms described by others were accurate so we opted to replace it.
On my machine there are tw ... Read more o screw on the front corners of the panel where the dials attach to the top of the washing machine. I removed those two screws and by lifting up and forward was able to move the whole thing out of the way.
You should see the connection from the dial panel running down into the wash basin. This is where you will unplug the old switch and replace it with a new one. There are little plastic clips that hold it in place, but you can squeeze them with your fingers to remove it from the panel.
In order to get access to the underside where the wires are connected you will need to remove two clips that hold the back pane to the rest of the sheet metal. In my case I wasn't quite prepared for the entire frame to move but once the clips are removed the back panel is completely removed and you can pull it forward to gain access to the underside.
Once you are able to get underneath you will see a screw that holds the ground wire. This is the one that you may need pliers to remove. There are two screws that hold the switch in place but you can access them at any time. I had already removed the old screws by this point. This should leave the switch disconnected from everything and you can install the new one.
Now just connect everything back together. The two screws for switch where the lid hits. Connect the ground wire and run the the connection back to the top portion where it will connect back up to the top panel.
I would add that there are two thin plastic strips that ran vertically up the back fo the back panel that meet the outer casing. I had to re-seat these before putting the clips back on the top.
The problem is the lid switch assembly is glued together and the original part came apart and needed to be replaced. The symptoms described by others were accurate so we opted to replace it.
On my machine there are tw ... Read more o screw on the front corners of the panel where the dials attach to the top of the washing machine. I removed those two screws and by lifting up and forward was able to move the whole thing out of the way.
You should see the connection from the dial panel running down into the wash basin. This is where you will unplug the old switch and replace it with a new one. There are little plastic clips that hold it in place, but you can squeeze them with your fingers to remove it from the panel.
In order to get access to the underside where the wires are connected you will need to remove two clips that hold the back pane to the rest of the sheet metal. In my case I wasn't quite prepared for the entire frame to move but once the clips are removed the back panel is completely removed and you can pull it forward to gain access to the underside.
Once you are able to get underneath you will see a screw that holds the ground wire. This is the one that you may need pliers to remove. There are two screws that hold the switch in place but you can access them at any time. I had already removed the old screws by this point. This should leave the switch disconnected from everything and you can install the new one.
Now just connect everything back together. The two screws for switch where the lid hits. Connect the ground wire and run the the connection back to the top portion where it will connect back up to the top panel.
I would add that there are two thin plastic strips that ran vertically up the back fo the back panel that meet the outer casing. I had to re-seat these before putting the clips back on the top.
Read less
Was this helpful?
Thank you for voting!
Agitator was barely agitating. Making a clicking noise.
17 of 18 people
found this instruction helpful.
-
Charmaine from Slidell, LA
- Easy
- 15 - 30 mins
-
Socket set
Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.
Was this helpful?
Thank you for voting!
Top Half of Agitator would not function without appying sideways pressure
18 of 21 people
found this instruction helpful.
-
Donald from Fredericksburg, VA
- Really Easy
- 15 - 30 mins
-
Socket set
Heard about the website... 1 minute to find it, 10 minutes to order new cogs... 3 day wait for new parts... Rec'd Fedex, 15 minutes total to pull the agitator cover (bleach dispenser) then the bung cover with o-ring (just lift out) expose bolt, unskrew and remove top portion of agitator or entire agitator if it's easier. Seperate, remo
... Read more
ve black cog holder (slides up the spindle) and replace cogs one at a time just like the old ones. Reassemble in reverse and you are back in business. Saved the $75 deductible on my home appliance warrenty. You guys are the best... cheers...
Read less
Was this helpful?
Thank you for voting!
Would not spin
24 of 40 people
found this instruction helpful.
-
floyd from Slidell, LA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.
Was this helpful?
Thank you for voting!
The washer did not spin fast enough during the rinse cycle to adequately dry the load of clothes
17 of 19 people
found this instruction helpful.
-
Richard from EL SEGUNDO, CA
- A Bit Difficult
- More than 2 hours
-
Socket set
I repaired my Kenmore washing machine replacing the clutch, Motor coupling and cogs. All of the parts came quickly and with good instructions. Best of all there were links to youtube repair walkthroughs. With out these step by step instructions this project would have taken much longer. Now the washer is like new! WATCH THE YOUTUBE PAUSE
... Read more
DO THE STEP AND REPEAT
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Top section of agitator not turning
17 of 20 people
found this instruction helpful.
-
John from Stone Mountain, GA
- Really Easy
- 15 - 30 mins
-
Socket set
Found directional gogs broken. Searched washer model # on PS.com and easily found schematic drawing. Received parts in a couple of days. Removed agitator with one nut, and other parts just pulled apart. Replaced the cogs and other parts which were not really broken....just worn. Everything went back together easily, and I was done!
... Read more
Parts Select saved me a LOT of time, and especially money, than if I had called a repair co. THANKS!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The Agitator in my washing machine wasn't spinning, and was loose.
15 of 15 people
found this instruction helpful.
-
Anton from BRONX, NY
- Really Easy
- 30 - 60 mins
-
Socket set
After researching and learning from the university of YouTube, I ordered new agitator 'dogs' from PartSelect - the rubbery dogs which look like gummy bears, were worn out in my machine and needed to be replaced. These dogs secure the inner part of the agitator. After watching several videos on YouTube, I knew precisely what to do and what
... Read more
I needed. I researched and found PartSelect on-line and they were very helpful and sending me the dogs. It was a very simple fix, and my washing machine now is working like brand new. Thanks PartSelect for all your help and will reach out again for any future self-fix projects!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water was leaking at the pump
17 of 21 people
found this instruction helpful.
-
Paul from Painesville, OH
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.
Was this helpful?
Thank you for voting!
Leaking drain hose
16 of 19 people
found this instruction helpful.
-
Steve from Cypress, CA
- Really Easy
- Less than 15 mins
-
Pliers
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.
Was this helpful?
Thank you for voting!