1102707 Kenmore Washer - Instructions

1. Unplug washer 2. Remove 3 plates off of the control box that attaches to the body of the washer 3. Using a 2 inch putty knife locate spring clips and push in to release 4. Lift top and secure 5. Lift up suspension rod and pop off the ball socket it sits in, then reach down and locate the clip of the suspension rod and push the tabs in. ... Read more It should just fall out. 6 make sure you clean the top well before reinstalling the new rod. 7. To install new suspension rod secure the top of the rod first then lift the drum and click in the bottom of the suspension rod. I recommend once you do the first rod then go to the back right corner and install that rod next. You will notice that their will be power and water lines on a clip that attaches to the rod. Disconnect from the rod and replace the rod. If you do this rod last the drum will have a lot of tension from the new springs and it will be difficult to install.

Remove agitator and replace hub. I also recommend replacing the Suspension too. I could tell the hub was bad the piece of metal washer on the bottom was gone. The suspension lost a lot of its stiffing

unscrew all the screws on the back of your cabrio washer just the bottom portion to access the drain pump which is located on bottom left underside of the wash drum, the drum on mine is plastic or plastic shroud i guess , theres 3 screws that hold the pump into place, also 2 hose clamps, and the power source, the cap that covers the power ... Read more source is a bit of a pain to unsnap do this part last cause you'll be able to pull it out from under the drum and get to it easier. once the pump is free just do everything in reverse and you'll be good to go in about 30 to 40 mins . one more thing dont try to caulk or seal on the one thats broke its a lost cause just replace it and make sure like i have been lol no coins left in your pockets before they get washed......whirlpool cabrio other number i got off sticker besides model number is type 580 hope this is helpfull

Followed video from you tube. Man made it look very easy. Not! Hole that lock has to come through in back was very tricky. Also, DO NOT THROW OUT OLD PART UNTIL NEW ONE IS INSTALLED. The reason for that is there is a CLIP at the end of the old part that is needed to attach new part to wire section in control panel. NO WHERE is it m ... Read more entioned at you got the clip from the old part. Luckily we saved it. Without that clip, you are screwed.

two small compression clamps hold the hoses in place. these are very simple to remove, however to reinstall the new hoses you should unscrew the pumps with a nut driver, secure the hoses with the clamps, and then screw the pump back to the bottom of the drum. oh yeah make sure to put the back plate back on the machine

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Was pretty strait forward. Took the back panel off, removed the 3 mount screws and 2 clamps on the pump, and swapped it all out. Only thing, Paid for 2 day air shipping, took a week for the part to come in. But it was still faster and cheaper then my local parts dealer.

Dismantled washer lid to install new locking mechanism.

First replaced four basket spring supports. Next tried Basket hub assembly ( which showed wear, but not total solution). Next replaced the rotation sensor that's on the stator. That finalized the issue.

The most difficult problem was to identify where the leak was and I tried to repair the old pump but that was a waste of my time. I was most impressed with this company in how fast the order was taken and the perfect part was shipped to me. I received the part in approx. 30 hours after I placed the order. The part was delivered by FedEx ... Read more press to my front door. A very reasonable price for the part. Anyway, most anyone could have done the repair that I did without difficulty.

I wasn't able to turn the washer on it's side or front, and instead had to prop it slightly up on cinder blocks due to the configuration of my laundry room. The actual repair was fairly simple, had the clamps supplied been easy to manuever, but they were not. The clamp that goes around the hose from the pump into the inlet valve wouldn't ... Read more go down around the valve where it was supposed to. I had it too far up, so when I ran the washer, the whole hose popped out and flooded my laundry room. My husband suggested a better clamp, the type that actually opens and you can tighten with a screw system. $2.16 at Lowes. 2nd attempt at repair was successful, and so far no leaks. So...save yourself some time and when you get the replacement pump, take those clamps over to Lowes or Home Depot and buy a clamp that you can open fully, slip over the valve, and tighten as much as you need. If I had that type of clamp to begin with, this project would have taken an hour, tops. And by the way, I'm a 36 year old woman with NO experience fixing appliances, but plenty of experience paying other people too much money to fix things that never should have broken in the first place!

Pretty easy! Just follow this link on how to fix the problem:

https://www.youtube.com/watch?v=_-Hg8rLGiKQ

The hardest part on fixing this is trying to move the washer out of its place so I can tilt it to see underneath the washer where the repair would be.

I followed the video instructions provided. However, I used the hook on an old rod to pull the new rods through the corner holes in the top of the dryer. Simple invert the old rod and feed through the hole, hook onto the new rod and lift through the hole. It enabled me to lift the tub with one hand and put the plastic seat and new rod ... Read more in place with the other hand. Too easy and sped up the repair job.

This was a very easy cure for the problem,

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.