1102647751K Kenmore Washer - Instructions

Remove the two screws holding the hinge to the washer body. Lift up on the hinge to remove from the washer. Remove all the screws holding the inner door piece to the outer cover. Remove the old hinge, replace with the new one. Put the two door pieces back together and tighten the screws. Place hinge back in on the washer body and pus ... Read more h down. Replace screw at top and bottom. Close door and start using.

I had replaced the flowmeter, but that didn't solve the problem, so I ordered the hot/cold solenoid fill part. Other than ONE screw that was unique -- the back retaining screws were nut driver screws, the one retaining screw was a torx which, of course, couldn't be seen unless you pulled the washer all the way out. Unscrewed that, unhooke ... Read more d the hose clamp with pliers and worried the hose off, removed the four electrical connections (which were TIGHT) and replaced the part. Turned on the water and was dismayed to get a d/l error code. After some colorful language learned from my drill sergeant 40 years ago, I realized that was "door lock" and closed the door tightly. Ran great and the Mrs. thinks I'm a hero.

Thank You so much for the other stories folks wrote on here! We were getting an F21 code on a regular basis. After finding a necklace and about $2.50 in change in the filter tray we found the problem. Over time I thought the washer was getting louder but it was so gradule that we really did not realize it.I had read other posts on here an ... Read more d ordered a new pump. After taking out 3 screws and 2 clamps the pump came right out and went in just as easy. Less than 15 minutes and we were back in business with a wisper quiet washing machine,Thanks Again everyone, Mike D.

I drained the water out of the pump area. Then took off all clamps and holding brackets. Next I pulled off the quick connect power plug. Then I put new pump in the way I took old pump out. The hardest part was unscrewing the bracket from underneath the washer. Cloth washer working fine.

Confirmed the issue was not a blocked trap at teh base of teh machine. Renoved the top of the machoine (Three 7mm hex-head sheet-metal screws). Removed the small hose (rubber tube) from the Water Level Pressure Switch. Confirmed the hose was not blocked or constricted. Removed the failed Water Level Pressure Switch by pinching the spring ... Read more -retainer with needle-nose pliers. Mounted the replacement WLPS. Connected hose. Tested the machine. PartSelect online catalog and delivery service was painless, quick, correct, only a little over-priced and easy.

Replace water pump

Very simple repair had to remove door from Washer, loosen the seals so that I could remove the old hinge. Inserted new hinge place the door and hinge on brackets and tightened the screws. I was very pleased with the fast action in getting me my parts, less than 24 hours.Thank You.

Unplugged electric cord and turned off water supply. Remove 3 screws @ rear of washer and removed top panel. Removed clamps on hoses and electrical connector to flow meter, removed and replaced with new flow meter. Replaced the top panel, turned on water supply and plugged unit in. Finished in less than 15 minutes. Saved myself several h ... Read more undred $

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

Well first of all when you buy this washer, the salesperson should tell you about checking the drain catch (ahead of the pump) and emptying out whatever get's caught in there. Never had a clue until it wouldn't work, then did a search on the internet, and darn if I didn't find specific instructions on how to open and clean out. Mine was p ... Read more acked full of hair pins, small change, lint, buttons, etc, all kinds of stuff. Guessing that is why the pump went out in the first place, it was so packed full that the pump could not draw any water through. But even after I cleaned it out, the pump was already shot. So called a service man, he said the pump would cost me around $200, then his labor to put it in, plus a $68 service call to just come and look at it, and $68 when he comes back to replace it. So I searched the internet for how to replace, came up with a very detailed You Tube video on how to replace Whirlpool Duet Pump. So ordered my pump from PartsSelect, just over $100, and replaced it myself. Super easy, only about 5 minutes. Thanks! —A very determined housewife!

Just went by instructions provided by parts web site

There are three screws in the back panel at the very top. I unscrewed them with a T25 driver tip and pulled the top panel off the machine, the water level pressure switch was located in the right rear corner of the washer. ( If you are facing the washer) I pulled off the hose and unplugged the old switch, popped the switch out, and snappe ... Read more d the new one in re-attached the plug and hose, put the top panel back on and the three screws back in! All in about fifteen minutes. My washer works like new.

It was real easy. I disconnected the wiring as shown in the video. I took the clamps off the drain pump , once off I slid the old drain pump off. I slid the new pump on , attached the hoses with the clamp provided and connected the wiring. Just follow the video and you will find it to be very easy! Thanks Parts Select for saving me mone ... Read more y

I just put the divider in the dispencer

unscrew the top 3 screws that hold the top lid on. Locate the pressure switch on the back right side, near the top. Pop off the pin plug (wire pack)and pull off the black hose. Put the pin plug into the new switch then put the black hose on. I did notice that the new pressure switch was a little bigger than the old one. It did not wan ... Read more t to pop into the retainer clip location so I just let it dangle. Its not a problem. Washer works like new.