110264 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
FH code-4 minutes into cycle
17 of 19 people
found this instruction helpful.
-
robert from LITLE RIVER, SC
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
remove 3 screws of top panel at rear. slide top to rear 1/2 inch and lift up. disconnect wire to flometer, remove clamps on hoses and remove, reverse to install. did not fix problem. ck'd screens at fill valves. ordered new fill valves--problem solved. solenoids must not have been opening up all the way.
Was this helpful?
Thank you for voting!
would not spin of agitate
20 of 28 people
found this instruction helpful.
-
Doug from Hartselle, AL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
I first had to take off the back and the top to get to the pulley and the belt. The pulley had woobled so much that it had worn out the center nad it would no longer hold to the post in the tub. It also had cut into the back of the tub about a 1/4 to 1/2 inch. I unscrewed the nut holding the pulley and removed it. I then took a knife and
... Read more
trimmed the rough edges off the back of the tub to make it smooth. I then smoothed out the end of the post that the pulley fits on so the new pulley would fit. I tightned the nut and put the belt on the motor drive shaft and Used a robo grip to hold the belt as I turned it onto the pulley. I but the back and top back on and that was it.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Would not spin
24 of 40 people
found this instruction helpful.
-
floyd from Slidell, LA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.
Was this helpful?
Thank you for voting!
The washer did not spin fast enough during the rinse cycle to adequately dry the load of clothes
17 of 19 people
found this instruction helpful.
-
Richard from EL SEGUNDO, CA
- A Bit Difficult
- More than 2 hours
-
Socket set
I repaired my Kenmore washing machine replacing the clutch, Motor coupling and cogs. All of the parts came quickly and with good instructions. Best of all there were links to youtube repair walkthroughs. With out these step by step instructions this project would have taken much longer. Now the washer is like new! WATCH THE YOUTUBE PAUSE
... Read more
DO THE STEP AND REPEAT
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Top section of agitator not turning
17 of 20 people
found this instruction helpful.
-
John from Stone Mountain, GA
- Really Easy
- 15 - 30 mins
-
Socket set
Found directional gogs broken. Searched washer model # on PS.com and easily found schematic drawing. Received parts in a couple of days. Removed agitator with one nut, and other parts just pulled apart. Replaced the cogs and other parts which were not really broken....just worn. Everything went back together easily, and I was done!
... Read more
Parts Select saved me a LOT of time, and especially money, than if I had called a repair co. THANKS!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The movers broke both water intakes off flush with the back of the machine
16 of 17 people
found this instruction helpful.
-
Dennis from Oak Island, NC
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.
Was this helpful?
Thank you for voting!
Water was leaking at the pump
17 of 21 people
found this instruction helpful.
-
Paul from Painesville, OH
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.
Was this helpful?
Thank you for voting!
Cold water flow was slow
22 of 36 people
found this instruction helpful.
-
Garry from Palm Bay, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Removed old part; exchanged rubber plungers between the hot and cold. Symptoms still the same - so eliminated the need for new rubber plungers (even though they still needed to be replaced). The only item left were the magnetic switches opening and closing the flows. The syphon was replaced due to broken plastic mountings causing the syph
... Read more
on to hang into the drum. Repair was a snap and finding the parts on your site was very easy and parts were there within 2 days at standard shipping. Thank you.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The Agitator in my washing machine wasn't spinning, and was loose.
15 of 15 people
found this instruction helpful.
-
Anton from BRONX, NY
- Really Easy
- 30 - 60 mins
-
Socket set
After researching and learning from the university of YouTube, I ordered new agitator 'dogs' from PartSelect - the rubbery dogs which look like gummy bears, were worn out in my machine and needed to be replaced. These dogs secure the inner part of the agitator. After watching several videos on YouTube, I knew precisely what to do and what
... Read more
I needed. I researched and found PartSelect on-line and they were very helpful and sending me the dogs. It was a very simple fix, and my washing machine now is working like brand new. Thanks PartSelect for all your help and will reach out again for any future self-fix projects!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
hoses had holes in them
18 of 25 people
found this instruction helpful.
-
Sharon from Dallas, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Put clamps on hose end and then used some dishsoap on the inside of the hose to make pushing them into place easier once in place I placed the clamp in correct spot and used a screwdriver to tighten the clamps.
Other Parts Used:
Was this helpful?
Thank you for voting!
Leaking drain hose
16 of 19 people
found this instruction helpful.
-
Steve from Cypress, CA
- Really Easy
- Less than 15 mins
-
Pliers
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.
Was this helpful?
Thank you for voting!
Washing machine leaking water
16 of 19 people
found this instruction helpful.
-
John from Oklahoma City, OK
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconne
... Read more
cted hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!
Read less
Was this helpful?
Thank you for voting!
leaking drain pump. Obviously a common problem with this washer
15 of 17 people
found this instruction helpful.
-
John from Solana Beach, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Wrench (Adjustable)
Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the we
... Read more
bsite parts diagram and whole website design is good.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washmachine wouldn't spindry
15 of 17 people
found this instruction helpful.
-
Chuck from South Holland, IL
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.
Was this helpful?
Thank you for voting!
washer overflowing
17 of 24 people
found this instruction helpful.
-
GREIG from CARTERSVILLE, GA
- Easy
- Less than 15 mins
-
Screw drivers
Repair was easy enough by just unlocking the tab and twisting the switch out from under the control panel. For me though, this did not fix my overflowing issue. After more research I found the inlet valve needed to be cleaned out.
I respect that electrical parts are non-returnable as I am in the auto parts business.
I respect that electrical parts are non-returnable as I am in the auto parts business.
Was this helpful?
Thank you for voting!