110263 Kenmore Washer - Instructions

I had read many sites describing the issue of water level being low in the washer. Many people had suggested that changing the water level switch fixes the problem. So I ordered the part from PartSelect.com and it came promptly within a few days.

1. Disconnect the power to the washer.
2. Pull on the knob that controls th ... Read more e water level and remove it.
3. Remove the 2 screws on the bottom of the control panel.
4. Give the front portion of the control panel a small yank and pull it forward, around and upward. (It is hinged on the top, so it swings out)
5. Now you have access to the water level switch.
6. Press the clip and turn the switch a quarter of a turn and it will come off the panel.
7. Pull the wire connected to the switch and remove it.
8. Pull the air tube connected to the switch and remove it.
9. Use the new water level switch and reverse the process.
10. Plug the washer back in an everything works great!

First I loosened the 2 screws on the outside of the top control assembly with a philips screwdriver. Then I took out the 2 other screws toward the top on the back with a socketwrench.Next I removed the top so I could access the switch. After that I removed the broken switch and unhooked from wire hareness. I then hooked up the new switch ... Read more and snapped into place. Last I put the top back on and screwed into place.

Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.

took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.

Removed old part; exchanged rubber plungers between the hot and cold. Symptoms still the same - so eliminated the need for new rubber plungers (even though they still needed to be replaced). The only item left were the magnetic switches opening and closing the flows. The syphon was replaced due to broken plastic mountings causing the syph ... Read more on to hang into the drum. Repair was a snap and finding the parts on your site was very easy and parts were there within 2 days at standard shipping. Thank you.

Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.

First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconne ... Read more cted hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!

First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.

Put clamps on hose end and then used some dishsoap on the inside of the hose to make pushing them into place easier once in place I placed the clamp in correct spot and used a screwdriver to tighten the clamps.

Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the we ... Read more bsite parts diagram and whole website design is good.

I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.

Repair was easy enough by just unlocking the tab and twisting the switch out from under the control panel. For me though, this did not fix my overflowing issue. After more research I found the inlet valve needed to be cleaned out.
I respect that electrical parts are non-returnable as I am in the auto parts business.

we looked at the video first then my husband fit the proble boy! was i excited! all the stores tried to get me to buy a new one. thanks partselets!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Unscrewed the two screws that hold the water lines to the valve. Unscrewed and lifted the control panel, popped the two spring clips that hold the back panel against the housing. Pulled the valve just outside the back panel. Took off the internal water line and moved it over to the new valve. Took off both hot and bold electric plugs a ... Read more nd moved them to the new valve. With the old valve off, I sled the new valve into place and screwed it to the back panel. Put the spring tabs back on the back panel and screwed the back panel back together. Plugged it in, attached the water supply lines and tested it. Worked fine.

I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's ... Read more lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.