110262 Kenmore Washer - Instructions

All Instructions for the 110262
121 - 135 of 1528

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Leaking water from bottom after wash
9 of 11 people found this instruction helpful.
  • Robert from Wildomar, CA
  • Easy
  • 30 - 60 mins
Turn washer on its side unscrewed clamps used pliers to slide clamps off of two hoses connected to pump then took clips off that hold pump replaced with new pump and put new clips connected hoses and clamps on new pump turned it back upright job finished
Was this helpful?
Thank you for voting!
Out of balance on spin cycle
9 of 11 people found this instruction helpful.
  • Tom from LATROBE, PA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Followed the videos on the website. But had to order parts twice because it wasn't the springs it was the plastic bushings the tub sits on that caused the wobble. No big deal though. All told it was still far less expansive than a new machine.
Was this helpful?
Thank you for voting!
washer would not spin clothes
8 of 8 people found this instruction helpful.
  • Joseph from KEARNY, NJ
  • Really Easy
  • 1- 2 hours
  • Socket set
Followed the video instructions. Had no problems. The video was accurate.
Was this helpful?
Thank you for voting!
there was a hole in the original drain hose
10 of 14 people found this instruction helpful.
  • Kathy from Pittsburgh, PA
  • Really Easy
  • Less than 15 mins
  • Pliers
First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new ho se onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!
Was this helpful?
Thank you for voting!
Timer was bad.
12 of 20 people found this instruction helpful.
  • Gary from Maple Grove, MN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I removed 4 screws holding the trim and timer mechanism.There is 1 phillips screw holding the timer to remove,and a plastic piece to pull out from the back of the timer.I easily pulled it off,and the timer fell right off.I removed the wiring harness,and removal was done.Installing the timer was a reversal of the process.Slide the timer in place.install 1 screw,snap wiring harness on.push timer dial on,shroud back in place and 4 screws to put back in. The whole process took me 15 minutes,and is a very simple fix.My wife was thrilled,and I was the hero!
Was this helpful?
Thank you for voting!
Washer basket off-center and wobbling during spin cycle
8 of 8 people found this instruction helpful.
  • Craig from Woodland Hills, UT
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.
Was this helpful?
Thank you for voting!
With full load, clothes were not agitating correctly - very little action or movement of the upper agitator section.
8 of 8 people found this instruction helpful.
  • Douglas from Lancaster, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Took off softener dispenser, pried off top of agitator, removed bolt from top of agitator.

Then pulled out the agitator assembly for easier access.

Used screwdriver to brake small plastic keepers holding secondary agitator ratchet clutch to the secondary agitator.

Assembled and inserted new ratchet mechan ism in the top of the agitator, making sure 4 small square pegs protruding from the end of the new assembly fully entered into mating holes on the secondary agitator.

Placed the agitator back on the agitator post and installed and secured bolt. Replaced cap and installed softener dispenser.
Was this helpful?
Thank you for voting!
Severe wobble during spin cycle.
9 of 11 people found this instruction helpful.
  • Steven from Dallas, GA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spr ing bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring.
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!
Was this helpful?
Thank you for voting!
Top section of the agitator would not work properly
12 of 20 people found this instruction helpful.
  • James from Crownsville, MD
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the top cap, unbolted the agitator, lifted off the top section, removed old "dogs" and replaced new "dogs", reinstalled agitator and tested.
Was this helpful?
Thank you for voting!
Direct drive pump was leaking
8 of 8 people found this instruction helpful.
  • Philip from DENTON, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I watched the video from the web site, decided that pulling the whole case was more work than needed. I tipped the washer back at about 45 degrees so that I could get under it and braced it so that it would not fall back fwd. Put a medium cooking bowl under the pump, used a channel locks to remove the 2 spring clamps that where around the hoses and slide the hoses off and let the water drain into the bowl. Then used a medium straight slot screw driver to release the clips from each side of the pump and slid the pump off the shaft. If you turn the clips 90 degrees they will slip out and had to remove the upper clip to get the pump out. Lined up the pump and the shaft making sure that the flat side of shaft and pump lined up and slid it on. Reinstalled the pump clips and slid the hoses back on the pump slide the clamps back in place lowered the washer and test ran it for leaks. Great Job NO leaks. Whole job took me less than 30 minutes.
Was this helpful?
Thank you for voting!
Spider coupling between motor and transmission broken
9 of 12 people found this instruction helpful.
  • Robert from Friendswood, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy rep air.
Was this helpful?
Thank you for voting!
banging noise during spin cycle, tub out of balance
8 of 9 people found this instruction helpful.
  • Russell from CHARLTON CITY, MA
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
I did the repairs after watching a few videos on this web site and it covered everything I needed. Went well and the parts were perfect.
Was this helpful?
Thank you for voting!
noisy
8 of 9 people found this instruction helpful.
  • clinton from selah, WA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
just like video showed really helpfull
Was this helpful?
Thank you for voting!
Washer would'nt spin
9 of 12 people found this instruction helpful.
  • Dean from Poplar Grove, IL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.
Was this helpful?
Thank you for voting!
washer would not spin to extract vwater
7 of 7 people found this instruction helpful.
  • Richard from WEEKI WACHEE, FL
  • Very Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
will not go over step by step here as there are already a multitude of stories on site with exact situation as mine who have already done so.. What I will say is that PartSelect is easily the absolutely best site on the net for a complete problem diagnosis to finished repair experience. Just input your model # and describe the problem and you get instant diagnosis probabilities along with access to a long list of customer Q & A and reviews, along with step by step videos on diagnosing, dis- assembling, and re-assembling along with links to all parts needed and also some secondary tips along the way. The prices are fabulous (example: I got a clutch assembly kit with several parts and 2 additional parts as a just in case for $55 shpg incl, while my local appliance parts place wanted $59 plus tax for just the main part in my assembly kit with a no return policy and no part guarantee, plus it was only 1 day more to have PartSelect pkg arrive than I would have gotten part from local store). This site is FABULOUS !!!
Was this helpful?
Thank you for voting!
All Instructions for the 110262
121 - 135 of 1528