- Home
- 11026002012
- Instructions
11026002012 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer would not adgitate
2 of 2 people
found this instruction helpful.
-
Joe from SAN JOSE, CA
- Very Easy
- Less than 15 mins
-
Nutdriver
I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to
... Read more
them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose
Joe M. San Jose
Read less
Was this helpful?
Thank you for voting!
Washer hoses due for replacement
3 of 5 people
found this instruction helpful.
-
James from PINE MOUNTAIN, GA
- Easy
- 30 - 60 mins
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this helpful?
Thank you for voting!
Washer would not agitate or spin and took over 2 hours to go through all cycles.
1 person
found this instruction helpful.
-
Danny from HARRISBURG, PA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
Started by replacing the lid latch assembly but this did not fix the problem. Parts Select representative suggested replacing the drive pulley clutch assembly. I order this and a new shift actuator. Had difficulty installing the new black shift actuator as it has a different electrical connection location from the original red part. The p
... Read more
lug on the existing wiring harness would not reach the socket on the new black shift actuator. I had to remove the socket from the new black actuator casing so the plug would reach the socket. Washer is now working.
Read less
Was this helpful?
Thank you for voting!
Washer would go into the cycle to rinse dry.
1 of 2 people
found this instruction helpful.
-
Daniel from WARMINSTER, PA
- Really Easy
- 30 - 60 mins
-
Socket set
Replacing the part was fairly easy. However it did not resolve the problem. The spin cycle did not activate,leaving my washer full of water. We ordered another Maytag Washer. Hopefully this one doesn't break down for a long time.
Was this helpful?
Thank you for voting!
door latch broke
0 of 1 people
found this instruction helpful.
-
Diana from Chimacum, WA
- Easy
- 15 - 30 mins
-
Nutdriver
Figuring out how to take the lid off was the hard part. Took out the old and replaced with new and put lid back on and rehooked up.
Was this helpful?
Thank you for voting!
Replace drain hose
3 of 11 people
found this instruction helpful.
-
Brian from DREXEL HILL, PA
- Easy
- 30 - 60 mins
-
Pliers
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people
found this instruction helpful.
-
Howard from Boynton Beach, FL
- Easy
- 30 - 60 mins
-
Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol
... Read more
oring refer handles. Thank you
Read less
Was this helpful?
Thank you for voting!
The lid lock switch on our clothes washer went out
-
Steven from Keenesburg, CO
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I had to remove 3 screws from the back of the washer to be able to lift the top. Then remove 3 screws under the lid which held the switch in, unplug the old part and put the new one in. It was quite sinple. The most difficult part was figuring out you have to slide the top of the washer forward a bit to be able to tilt it up.
Was this helpful?
Thank you for voting!
would not unlock
-
Michael from Lincoln, RI
- Easy
- 15 - 30 mins
-
Screw drivers
Disassembled ,as assembled.
Was this helpful?
Thank you for voting!
Latch Assembly and lock broke
-
DIANE*RACHAL from SHREVEPORT, LA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
I taught I might have to replace the whole machine. Then I realize we had power but the latch and lock assembly wasn't locking for the machine to lock and start to wash. Unplug the washer, took the top off of washer, unscrew two bolts from latch assembly, replace latch assembly and two bolts. then unscrew two bolts from lock and replace
... Read more
it. Machine works great now.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Bad latch lock
-
David B from Madison, IN
- Really Easy
- 15 - 30 mins
-
Nutdriver
Took the back of the control panel off, lifted the top of the washing machine up took off nuts holding the latch lock off, installed the new parts put back together. Piece of cake...because i got the right parts the first time. Thank you PartSelect.
Other Parts Used:
Was this helpful?
Thank you for voting!
Lid lock would not ingague.
-
Tom from Franklin, IN
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed two brackets on back top of washer that hold top secure. Pulled top forward and up off off pins located on front top of washer. Located switch removed two screws holding it in. Then removed Panel on back of top in order to get to controls and unplugged other end of switch. Then reversed procedure and waher was back in service.
Was this helpful?
Thank you for voting!