110248 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken water inlet syphon combined with missing feet was causing water to spill out of the washer
17 of 36 people
found this instruction helpful.
-
Randy from Atlanta, GA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.
Other Parts Used:
Was this helpful?
Thank you for voting!
No agitation, No spin, pump OK
7 of 7 people
found this instruction helpful.
-
Ernest from Midlothian, VA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold
... Read more
the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The water intake hose had a hole and was leaking. I think a rat chewed it.
7 of 7 people
found this instruction helpful.
-
JANET from GERMANTOWN, NY
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
I first watched a YouTube video on how to open up the machine. It was a breeze. I removed the part the hose attaches to where the water comes out and into the tub. The hardest part was removing the old hose clamps. Had I known I would have used new clamps. I took off old hose and replaced with the new one, it took longer because of the cl
... Read more
amp issue. Otherwise it went fairly easy, to my surprise. Even tho I am a 70 yr old woman I will try to fix what I can. Doing this saved me at least $600. For a new washing machine. I'm so proud of myself.
Read less
Was this helpful?
Thank you for voting!
washer would not spin to extract vwater
7 of 7 people
found this instruction helpful.
-
Richard from WEEKI WACHEE, FL
- Very Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
will not go over step by step here as there are already a multitude of stories on site with exact situation as mine who have already done so.. What I will say is that PartSelect is easily the absolutely best site on the net for a complete problem diagnosis to finished repair experience. Just input your model # and describe the problem and
... Read more
you get instant diagnosis probabilities along with access to a long list of customer Q & A and reviews, along with step by step videos on diagnosing, dis- assembling, and re-assembling along with links to all parts needed and also some secondary tips along the way. The prices are fabulous (example: I got a clutch assembly kit with several parts and 2 additional parts as a just in case for $55 shpg incl, while my local appliance parts place wanted $59 plus tax for just the main part in my assembly kit with a no return policy and no part guarantee, plus it was only 1 day more to have PartSelect pkg arrive than I would have gotten part from local store). This site is FABULOUS !!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water Pump was leaking
9 of 13 people
found this instruction helpful.
-
Rick from Liberty, SC
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.
I turned the washer on its side and felt where the leak was on th ... Read more e pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.
I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!
I turned the washer on its side and felt where the leak was on th ... Read more e pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.
I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
No parts
7 of 7 people
found this instruction helpful.
-
Jason from WENTZVILLE, MO
- Very Difficult
- More than 2 hours
A label was created and never shipped. Sat there for 2 weeks.
Contacted company for a refund and a Retha’s never been issued.
Terrible service!
Contacted company for a refund and a Retha’s never been issued.
Terrible service!
Other Parts Used:
Was this helpful?
Thank you for voting!
Lid Switch Screw Mounts Broke
7 of 8 people
found this instruction helpful.
-
Leo from Compton, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I had to unscrew 2 screws that held the control panel, then remove the 2 end caps, remove 2 screws that held the control panel to the washing machine. I then lifted the control panel and leaned the lower case forward. All this to get access to the ground screw for the lid mount. It sounds like a lot, but actually it was quite simple. I re
... Read more
placed the old switch with a new one and put everything back together just like new. No extra screws or parts that I could not remember where they came from. Thanks Parts Select. Reading the comments from others helped me to realize that I could do the work without worry. The only problem I had was ordering the correct part. That did not happen until I got the correct part number from the old part.
Read less
Was this helpful?
Thank you for voting!
Ground prong on power cord was broken
10 of 17 people
found this instruction helpful.
-
RONALD from PORT ORCHARD, WA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Disconnected old power cord inside control cabinet, removed strain relief , then removed damaged power cord. Reinstalled new cord with new strain relief.
Other Parts Used:
Was this helpful?
Thank you for voting!
Fabric Softener dispenser was broken
7 of 8 people
found this instruction helpful.
-
Steve from Lufkin, TX
- Really Easy
- Less than 15 mins
Replacing the fabric softener dispenser was very easy. It just snaps on. Make sure you line up the tabs with the holes in the agitator, otherwise it will not stay on and will fly off and break in the spin-cycle. This is how the first one broke to begin with.
Was this helpful?
Thank you for voting!
top agitator would not operate
8 of 11 people
found this instruction helpful.
-
Larry from Edgewood, TX
- Really Easy
- Less than 15 mins
-
Socket set
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.
Was this helpful?
Thank you for voting!
Agitator not working
7 of 8 people
found this instruction helpful.
-
kevin from oxford, PA
- Really Easy
- Less than 15 mins
-
Wrench set
Removed cap, used a wrench to remove nut for agitator, put new one in place put nut back on and the cap back on and started washing clothes easy fix saved me $300.00 Thank you
Was this helpful?
Thank you for voting!
Broken Fabric Softener Dispenser
8 of 11 people
found this instruction helpful.
-
JOAN from Little Elm, TX
- Really Easy
- Less than 15 mins
Just removed the broken part and replace it with the new one.
Was this helpful?
Thank you for voting!
Washer would sometimes not go into spin cycle. Opening and closing lid would put it into spin.
7 of 8 people
found this instruction helpful.
-
Donald from Toopeka, KS
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed end caps on control panel, removed two screws, lifted the control panel and rolled it back out of the way.
Undid clips and wire connection and pulled the cabinet off. Replaced the switch and put everything back together.
Easy job but helps to have two people to get the cabinet back on right.
Undid clips and wire connection and pulled the cabinet off. Replaced the switch and put everything back together.
Easy job but helps to have two people to get the cabinet back on right.
Was this helpful?
Thank you for voting!
Washer would not work in agitate or spin cycle
6 of 6 people
found this instruction helpful.
-
yesenia from apopka, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off wit
... Read more
hout unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.
The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.
It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.
The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.
It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.
Read less
Was this helpful?
Thank you for voting!
The middle tub would not come out
7 of 9 people
found this instruction helpful.
-
Jayanti from SNELLVILLE, GA
- Very Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , ... Read more I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , ... Read more I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
Read less
Was this helpful?
Thank you for voting!