110247 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Would not spin
24 of 40 people
found this instruction helpful.
-
floyd from Slidell, LA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.
Was this helpful?
Thank you for voting!
The washer did not spin fast enough during the rinse cycle to adequately dry the load of clothes
17 of 19 people
found this instruction helpful.
-
Richard from EL SEGUNDO, CA
- A Bit Difficult
- More than 2 hours
-
Socket set
I repaired my Kenmore washing machine replacing the clutch, Motor coupling and cogs. All of the parts came quickly and with good instructions. Best of all there were links to youtube repair walkthroughs. With out these step by step instructions this project would have taken much longer. Now the washer is like new! WATCH THE YOUTUBE PAUSE
... Read more
DO THE STEP AND REPEAT
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washing Machine not draining
17 of 19 people
found this instruction helpful.
-
Kay from Houston, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
1. Watch the partselect.com repair videos for either of the following parts: Part # 3363394 (White Direct Drive Water Pump - two ports) or Part # 285753A (Direct Drive Coupling).
2. After disconnecting the washing machine from the wall, these videos will show you how to disconnect the frame off the washing drum from the front. Disco ... Read more nnecting the top panel is a little different: pull/pop the two end pieces off, and unscrew the screws.
3. Upon removal of the front frame (per videos), disconnect the electrical device from underneath the lid, using a phillips screwdriver and a nutdriver and/or wrench. Use a flathead screw driver for the clips to remove/replace the electrical wires. No need to splice/cut any wiring.
4. Put everything back together.
2. After disconnecting the washing machine from the wall, these videos will show you how to disconnect the frame off the washing drum from the front. Disco ... Read more nnecting the top panel is a little different: pull/pop the two end pieces off, and unscrew the screws.
3. Upon removal of the front frame (per videos), disconnect the electrical device from underneath the lid, using a phillips screwdriver and a nutdriver and/or wrench. Use a flathead screw driver for the clips to remove/replace the electrical wires. No need to splice/cut any wiring.
4. Put everything back together.
Read less
Was this helpful?
Thank you for voting!
The movers broke both water intakes off flush with the back of the machine
16 of 17 people
found this instruction helpful.
-
Dennis from Oak Island, NC
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.
Was this helpful?
Thank you for voting!
Cold water flow was slow
22 of 36 people
found this instruction helpful.
-
Garry from Palm Bay, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Removed old part; exchanged rubber plungers between the hot and cold. Symptoms still the same - so eliminated the need for new rubber plungers (even though they still needed to be replaced). The only item left were the magnetic switches opening and closing the flows. The syphon was replaced due to broken plastic mountings causing the syph
... Read more
on to hang into the drum. Repair was a snap and finding the parts on your site was very easy and parts were there within 2 days at standard shipping. Thank you.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Somehow or another, the plastic cup inside vanished.
17 of 21 people
found this instruction helpful.
-
Warren from Lakewood, CO
- Really Easy
- Less than 15 mins
This was a really easy replacement job. All I had to do was twist the old Fabric Softener Dispenser to the left to unlock it, pull it off, and put the replacement on.
Was this helpful?
Thank you for voting!
Water was leaking at the pump
17 of 21 people
found this instruction helpful.
-
Paul from Painesville, OH
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.
Was this helpful?
Thank you for voting!
Lid Switch broke had to replace.
15 of 16 people
found this instruction helpful.
-
Michael from Litchfield, IL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench set
The biggest problem for me was finding the screws to remove the control panel. First there are two screws on the top back side of the control panel, then there are plastic covers that have to be removed from both sides of control panel, then you can remove the screws at the base of the control panel. Set the control panel back, then re
... Read more
move the golden brackets that hold the cabinet to back of the washer. The whole cabinet will come forward with a little coaxing. (Remember to put the screws with the part you have removed to make sure you put them back in the same place.) Next remove screws that hold on the lid switch, remove wiring from clips, then replace with new switch, situate wiring in clips, position switch into place, screw into place. The cabinet is really hard to get back into place, be patient it may take a few tries. Once you get the cabinet in place, replace the golden brackets, then place the control panel where the screw holes line up and screw down, replace plastic sides, then replace the screws in the back side and your done.
Read less
Was this helpful?
Thank you for voting!
Leaking drain hose
16 of 19 people
found this instruction helpful.
-
Steve from Cypress, CA
- Really Easy
- Less than 15 mins
-
Pliers
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.
Was this helpful?
Thank you for voting!
Washing machine leaking water
16 of 19 people
found this instruction helpful.
-
John from Oklahoma City, OK
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconne
... Read more
cted hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!
Read less
Was this helpful?
Thank you for voting!
Washmachine wouldn't spindry
15 of 17 people
found this instruction helpful.
-
Chuck from South Holland, IL
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.
Was this helpful?
Thank you for voting!
leaking drain pump. Obviously a common problem with this washer
15 of 17 people
found this instruction helpful.
-
John from Solana Beach, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Wrench (Adjustable)
Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the we
... Read more
bsite parts diagram and whole website design is good.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer worked fine but wouldn't spin. Hot smell. I could turn tub by hand to help it get started and it would spin okay. Silver clutch cover was very hot to touch.
17 of 24 people
found this instruction helpful.
-
Kevin from Disputanta, VA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's
... Read more
lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.
Read less
Was this helpful?
Thank you for voting!
my cold water did not run in the machine and it would not rinse
15 of 18 people
found this instruction helpful.
-
TONYA from DISTRICT HEIGHTS, MD
- Easy
- Less than 15 mins
-
Screw drivers
we looked at the video first then my husband fit the proble boy! was i excited! all the stores tried to get me to buy a new one. thanks partselets!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Was this helpful?
Thank you for voting!
washer overflowing
17 of 24 people
found this instruction helpful.
-
GREIG from CARTERSVILLE, GA
- Easy
- Less than 15 mins
-
Screw drivers
Repair was easy enough by just unlocking the tab and twisting the switch out from under the control panel. For me though, this did not fix my overflowing issue. After more research I found the inlet valve needed to be cleaned out.
I respect that electrical parts are non-returnable as I am in the auto parts business.
I respect that electrical parts are non-returnable as I am in the auto parts business.
Was this helpful?
Thank you for voting!