110246 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced ring that broke and washer that was bent on the edge.
22 of 47 people
found this instruction helpful.
-
Kim from West Liberty, OH
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and starte
... Read more
d stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer would not spin a full load.
11 of 15 people
found this instruction helpful.
-
Ralph from Newbury Park, CA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
!. Removed agitator from inside
2.Removed outside cabinet
3 Removed pump, motor, and transmission.
4. Slid the entire drive unit out of the tub from the bottom
5. Removed the clutch assy. and installed new.
6. Reverseed the procedure to re-assemble.
2.Removed outside cabinet
3 Removed pump, motor, and transmission.
4. Slid the entire drive unit out of the tub from the bottom
5. Removed the clutch assy. and installed new.
6. Reverseed the procedure to re-assemble.
Was this helpful?
Thank you for voting!
My drain hose had cracked and was leaking.
10 of 12 people
found this instruction helpful.
-
Miguel from San rafael, CA
- Easy
- Less than 15 mins
-
Wrench (Adjustable)
Once I finally found the part I needed, the repair was very simple and took only a few minutes. Thanks to the very helpful operator to walk me through the diagram to find the corresponding number for the part. I really appreciate your help!
Was this helpful?
Thank you for voting!
Tub banged against the front of case during spin
9 of 9 people
found this instruction helpful.
-
Peter from Boca Raton, FL
- A Bit Difficult
- Less than 15 mins
-
Screw drivers
3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the
... Read more
suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.
Read less
Was this helpful?
Thank you for voting!
Washer tub off balance and noisy
9 of 10 people
found this instruction helpful.
-
Gregory from Kent, OH
- A Bit Difficult
- 30 - 60 mins
-
Pliers
The repair was fairly simple and while it made the spin operation quieter and and a bit more stable, it still gets out of balance. Disconnected power, shutoff supply lines and disconnected them from the unit.
Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverag ... Read more e with a 2 x 4 to take any residual tension off the springs.
Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors
Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.
If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.
Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverag ... Read more e with a 2 x 4 to take any residual tension off the springs.
Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors
Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.
If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.
Read less
Was this helpful?
Thank you for voting!
Machine agitated during cycle but would not spin clothes dry.
10 of 13 people
found this instruction helpful.
-
Kurt from Bremerton, WA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Followed the excellent video instructions. They say you can perform the repair without removing the enclosure, but when I saw how easy it was to remove it, it definitely improves the access and speeds the repair. Have a piece of wire handy to to hold the pump assembly out of the way. Installed new clutch kit and it runs like a champ.
Was this helpful?
Thank you for voting!
Spin cycle not working properly; Clothes still soaked when spin cycle finished
12 of 19 people
found this instruction helpful.
-
Sarah from Columbus, OH
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
We ordered both the motor coupling and the clutch assembly based on our troubleshooting, and because we figured both parts were inexpensive enough we might as well have them both. We initially thought it was the clutch assembly, but as we were taking the washing machine apart, we noticed that actually one of the bolts was missing complet
... Read more
ely and one had snapped in two. We then realized that the spin cycle problem was actually related to the instability of the motor because of the missing/broken bolts (they didn't even have washers!). All we had to do was replace the bolts and use a bolt extractor to get the broken bolt out, but we went ahead and replaced the clutch assembly as well for good measure. Everything ran perfectly after that! I was very skeptical to do the repair myself, but it really is easy, as long as you have someone with muscle to help out. You can also look up videos online that show you a step by step repair process for the clutch assembly, and I would highly recommend doing that so that you have a visual. It will make everything seem 100x easier.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washing machine shakes violently during spin cycle
25 of 58 people
found this instruction helpful.
-
James from Asheville, NC
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed four screws that hold the top control panel to the base and hung over the back panel in order to remove the main wrap-around body of the machine. Took off top plastic ring fastened to side of tub then removed old Balance ring. Installed new balance ring. Unfortunately, this did NOT fix the problem. This was a suggestion from Justa
... Read more
nswer.com and failed miserably. Does anybody know how to fix this problem? And it's not the springs or the little plastic shims around the base OR the cross coupling to the motor...
Read less
Was this helpful?
Thank you for voting!
Tub off center. Upper agitator not driven.
10 of 13 people
found this instruction helpful.
-
Thomas from Addison, NY
- Easy
- 15 - 30 mins
-
Pliers, Socket set
Pop off the softener dispenser. Pull the cover/ seal out of the upper agitator. With 7/16" socket and extesion bar, remove bolt and pull upper agitator straight up and off. dump out old assembly and replace with new assembly. Set back in place and replace bolt. Repair kit comes with good instructions and new rubber O ring for bolt cover/
... Read more
seal. (thanks).
The suspension spring takes more effort but not hard. with washer laying on face I used a piece of 2x4 to pick up the tub in the direction of the broken spring. Put the new spring through the wire hook loop and snake it through the slot in the frame and you can see how it locks in place. With the 2x4, push the tub toward the new spring until you can hook it through the slot on the tub frame. Done. Parts cost less than an estimate from a service call and I finished the job in 30 minutes, which includes unplugging the power cord, turning off the water and taking off the hoses so I could lay the washer down. Saved the website in my favorites for the same great prices and fast shipping next time.
The suspension spring takes more effort but not hard. with washer laying on face I used a piece of 2x4 to pick up the tub in the direction of the broken spring. Put the new spring through the wire hook loop and snake it through the slot in the frame and you can see how it locks in place. With the 2x4, push the tub toward the new spring until you can hook it through the slot on the tub frame. Done. Parts cost less than an estimate from a service call and I finished the job in 30 minutes, which includes unplugging the power cord, turning off the water and taking off the hoses so I could lay the washer down. Saved the website in my favorites for the same great prices and fast shipping next time.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Leaking water from bottom after wash
9 of 11 people
found this instruction helpful.
-
Robert from Wildomar, CA
- Easy
- 30 - 60 mins
Turn washer on its side unscrewed clamps used pliers to slide clamps off of two hoses connected to pump then took clips off that hold pump replaced with new pump and put new clips connected hoses and clamps on new pump turned it back upright job finished
Other Parts Used:
Was this helpful?
Thank you for voting!
Direct drive pump was leaking
8 of 8 people
found this instruction helpful.
-
Philip from DENTON, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I watched the video from the web site, decided that pulling the whole case was more work than needed. I tipped the washer back at about 45 degrees so that I could get under it and braced it so that it would not fall back fwd. Put a medium cooking bowl under the pump, used a channel locks to remove the 2 spring clamps that where around the
... Read more
hoses and slide the hoses off and let the water drain into the bowl. Then used a medium straight slot screw driver to release the clips from each side of the pump and slid the pump off the shaft. If you turn the clips 90 degrees they will slip out and had to remove the upper clip to get the pump out. Lined up the pump and the shaft making sure that the flat side of shaft and pump lined up and slid it on. Reinstalled the pump clips and slid the hoses back on the pump slide the clamps back in place lowered the washer and test ran it for leaks. Great Job NO leaks. Whole job took me less than 30 minutes.
Read less
Was this helpful?
Thank you for voting!
Out of balance on spin cycle
9 of 11 people
found this instruction helpful.
-
Tom from LATROBE, PA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Followed the videos on the website. But had to order parts twice because it wasn't the springs it was the plastic bushings the tub sits on that caused the wobble. No big deal though. All told it was still far less expansive than a new machine.
Other Parts Used:
Was this helpful?
Thank you for voting!
washer would not spin clothes
8 of 8 people
found this instruction helpful.
-
Joseph from KEARNY, NJ
- Really Easy
- 1- 2 hours
-
Socket set
Followed the video instructions. Had no problems. The video was accurate.
Other Parts Used:
Was this helpful?
Thank you for voting!
there was a hole in the original drain hose
10 of 14 people
found this instruction helpful.
-
Kathy from Pittsburgh, PA
- Really Easy
- Less than 15 mins
-
Pliers
First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new ho
... Read more
se onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!
Read less
Was this helpful?
Thank you for voting!
Washer basket off-center and wobbling during spin cycle
8 of 8 people
found this instruction helpful.
-
Craig from Woodland Hills, UT
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.
Was this helpful?
Thank you for voting!