110240 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Leaking pump
3 of 4 people
found this instruction helpful.
-
Paul from GARNER, NC
- Really Easy
- 30 - 60 mins
I could not make the repair. If you get the pump specified on the shaft that drives the pump, the pump will be broken. I tried to call, nobody answers the phone. I ended up buying a Washing Machine and I'm stuck with a pump I cannot use.
Other Parts Used:
Was this helpful?
Thank you for voting!
could not get the bottom agitator to release, so finally just left it in place, first bolt I had did not fit right so ordered one directly from your store also had to wait dor my tools to get in
3 of 4 people
found this instruction helpful.
-
Linda Dianne from Poteau, OK
- A Bit Difficult
- More than 2 hours
-
Socket set
I am an old woman who is disabled and without any tools or knowledge, but sheer stubbornness and will power, I waited for my tools and other parts to come in, in the mean time I fixed my young neighbors whirlpool washer, well We took top off the nut I had already pre assembled her cam so set it in place of old one put bolt back in place a
... Read more
nd the top of agitator she says works perfectly now, my parts came in I had nothing to remove as my handicap daughter had already thrown away all the loose parts, I threw away old top agitator, assembled cam and put in place still did not feel tight enough so added seal from other nut!! it worked tight enough, put the inner part back in with new part and soap put the top back on and now works good as new, was disappointed could not put bottom agitator in place, just not strong enough lol well this was my story
Read less
Was this helpful?
Thank you for voting!
Water leak
3 of 4 people
found this instruction helpful.
-
Joe from Buelton, CA
- Easy
- 30 - 60 mins
Disconneted hoses,unplugged.removed drain hose.Turned unit on its side.Unsnapped retainers,tryed to to pull off with just my hands,that didn't work.Used a pry bar to pop off.The end of the shaft was rusted out.I took a dremel with wire brush and cleaned up the end.Then the pump njust slid on.I took it off again and applied some anti-sieze
... Read more
on the end of shaft.then put pump back on.Snapped the retainers and put hoses back on.It was easy.When I first looked up washer parts,I found this other site and the price ws doulbe.Then I found you guys ,1/2 the cost and it was here in 2 days.Thank You Parts select.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water Pump Replacement
3 of 4 people
found this instruction helpful.
-
Jim from Hamburg, NY
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
Yes, I agree that the actual replacement of the pump was an easy task on this whirlpool washing machine, however, unlike other posters, I had no access through the bottom of the machine. My machine has a solid pan on the bottom. It has a large hole in the center - I think to access the transmission, but no access where the pump is.
... Read more />So, I had to dismantle the entire enclosure, first the back (about 6 screws, a couple of electrical connections, etc.), then remove the rest of the enclosure to reveal the guts of the machine. I also had to disconnect a small vacuum tube attached to the tub, and remove the control console on top along with the back. It was pretty straight forward, took about two hours to dismantle. Then, the actual removal of the pump was as easy as others have described here - two spring clips and a hose clamp and I had it in my hand. I ordered the new part, which came very quickly - 2 days I think. Then I took another two hours to re-assemble the machine. It works - yeah!
Symptoms - water leak on the floor, it was actually intermittent for a time, so I procrastinated. Then when I actually did the work, I could see the rust trail and follow it to the leaky pump. The pump was actually leaking through the center, where the drive shaft from the motor goes. There is probably a seal between the impeller and the central drive slot that gives out after a while.
New pump in - machine back together - no leaks.
... Read more />So, I had to dismantle the entire enclosure, first the back (about 6 screws, a couple of electrical connections, etc.), then remove the rest of the enclosure to reveal the guts of the machine. I also had to disconnect a small vacuum tube attached to the tub, and remove the control console on top along with the back. It was pretty straight forward, took about two hours to dismantle. Then, the actual removal of the pump was as easy as others have described here - two spring clips and a hose clamp and I had it in my hand. I ordered the new part, which came very quickly - 2 days I think. Then I took another two hours to re-assemble the machine. It works - yeah!
Symptoms - water leak on the floor, it was actually intermittent for a time, so I procrastinated. Then when I actually did the work, I could see the rust trail and follow it to the leaky pump. The pump was actually leaking through the center, where the drive shaft from the motor goes. There is probably a seal between the impeller and the central drive slot that gives out after a while.
New pump in - machine back together - no leaks.
Read less
Was this helpful?
Thank you for voting!
Wash Stil Wet After Cycle Complete( Spin Cycle Not Working) Funny Noise When Should Be Spinning
4 of 7 people
found this instruction helpful.
-
Scott from Miami, FL
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Started taking machine apart, would of been easier if I had looked at the online diagrams first, but dismantled enough to find a few broken parts, I could not tell the coupling was broke till I actually removed the water pump and motor. Total cost for 3 plastic parts was less than $25 including shipping. Received parts in 3 days on st
... Read more
andard lowest cost shipping. Put machine back together, with just a few extra screws and wire clips, but machine works like new now. Much better than the cost of new or used washer.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer not spinning properly.
3 of 4 people
found this instruction helpful.
-
Juana from MANOR, TX
- Very Easy
- Less than 15 mins
-
Nutdriver
Being female & never working on appliances, it was a challenge for me. I took the spinning unit apart: 1) Outer cap 2) Inner cap 3) Screw, nut & bolt popped out. Rusty & wouldn't lock into place anymore. Ordered nut & washer at about $10 + shipping. Total $17 from MayTag Rec'd right at 7 days via USPS. Used nutdriver/wrench to scre
... Read more
w in new bolt w/washer. Wah la! That did it! Washer working great now! Now that I'm a "diy" handy person, I'm ready for my next challenge. Hopefully, none!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
rubber seal broke aprt
3 of 4 people
found this instruction helpful.
-
Lisa from North Attleboro, MA
- Really Easy
- Less than 15 mins
slid the old seal off the lid and the new one popped on so easily
I do so many self- repairs at home now this was not even an issue.
I do so many self- repairs at home now this was not even an issue.
Was this helpful?
Thank you for voting!
Water overflow when set at Ex-Lge load
3 of 4 people
found this instruction helpful.
-
Robert from Sodus Point, NY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
After moving washer and UN-Plugging electrical. 1. Remove the 2 screws that hold the Control Panel to the lower chassis. 2. Lift the Control Panel up and forward to expose the water level switch. 3. Remove the dial. 4. Remove the old switch, (a plastic tab locks it into the panel, try to release it(from the front) with a small screwd
... Read more
river, (mine broke off, releasing the switch). 5. Remove the electrical connection by lifting the connection locking tab. 6. Remove the air tube. 7. BLOW into the air tube to ensure it is not blocked. 8 . Reconnect the air tube and electrical connection. 9. Carefully install the new switch into place, turning it to line up and lock the tab into the panel. 10. Re-install the dial and return the Control Panel screws into the lower chassis. NOTE: If the included air hose needs to be replaced, the time and difficulty needed to make repairs will increase.
Read less
Was this helpful?
Thank you for voting!
Washer would not fill with water
4 of 7 people
found this instruction helpful.
-
Eddie from Charlotte, NC
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Tried replacing the water valve first (85% - this is the problem... from the website)... It did not fix the problem. Ordered the water level switch (10% - this is the problem... from the website).. It works like new.
The website had lots of information, videos, specs, etc. It really helped a lot...!! Feels good to fix a washer ... Read more that did not work... Thanks partselct.com...!!! -Eddie Campbell, Charlotte, NC
The website had lots of information, videos, specs, etc. It really helped a lot...!! Feels good to fix a washer ... Read more that did not work... Thanks partselct.com...!!! -Eddie Campbell, Charlotte, NC
Read less
Was this helpful?
Thank you for voting!
Motor Running But Agitator Not Moving
2 of 2 people
found this instruction helpful.
-
Phillip from Osceola Mills, PA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Unplug power cord. Turn off hot and cold water to washer. Disconnect water lines at the back of the washer, but mark which is hot and cold on the hoses . Remove drain hose from the sink tub or sewer line but keep it elevated so the water don't run out. Tip over on the backside but put something under the back side like a tool box to
... Read more
keep the top elevated a little bit, but not on the control panel just below it. Now remove the two screws that are in the motor retainer. Now pry motor retainers loose then lift out motor and remove old coupling. Now install new coupling. If it is a little tight on the shaft, use a deep socket a little bigger than the shaft to tap them on. Line up coupling while putting motor in place. Then snap on motor retainers. Look at the coupler make sure it is straight and not s shape. If it is s shape, remove and tap coupler on shaft a little more. If it is straight then reinstall the two screws you removed in the beginning from the motor retainers. Hook up drain line, water lines hot to hot, cold to cold. Then check for leaks on water lines. Plug in ,turn on, if it sounds ok. Don"t stand there, wash something.
Read less
Was this helpful?
Thank you for voting!
Washing machine was very loud and walked across the floor
2 of 2 people
found this instruction helpful.
-
Michael from PORTAGE, MI
- Easy
- 30 - 60 mins
It was a miracle. We were going to get rid of the washing machine because it made so much noise and rattled the whole house. It also 'walked' across the room with every load.
I simply replaced the wear pads (2 of them were already worn away), and now it is as quiet as when it was new. AMAZING!
I simply replaced the wear pads (2 of them were already worn away), and now it is as quiet as when it was new. AMAZING!
Was this helpful?
Thank you for voting!
Was heavily shaking.
2 of 2 people
found this instruction helpful.
-
Robert from LEWISTON, ID
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Old machine and vibrations are still there but weaker. Seemed to turn counter clock wise. Put a 4x4 board behind in order to stop the twisting, and keep hoses safe from vibrating and causing wear. Stays fairly stable now.
Was this helpful?
Thank you for voting!
I was getting a high pitched noise during the draining of the washer with a plastic friction smell
2 of 2 people
found this instruction helpful.
-
Stephen from SCHENECTADY, NY
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I followed the instructions in the video on the part page (part #PS11741239), which was also conveniently linked in the item shipped email. The replacement of the part was very easy ... the hard part was balancing the washer again (kitchen floor seems to have sunk in the middle). Back to normal function without having to suffer a flood fi
... Read more
rst. Thanks.
Read less
Was this helpful?
Thank you for voting!
My washer would occasionally leak water on the floor.
2 of 2 people
found this instruction helpful.
-
Lary from Broadway, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
This model is a compact / apartment size washer and the repair was fairly easy. The lid is held on by 2 spring clips on the front and 2 tabs on the rear. I used a screwdriver to pop the top off the clips, removed the screws on the tabs, unplugged the switch and set the top aside. Took out 2 screws (all screws are 5/16" hex head) on the l
... Read more
eft side panel (facing the front of the machine) and set it to the side. The pump is clearly visible at this point. Tipped the washer and propped it up for easier access. Removed the 2 hose clamps (set a pan underneath first) and the pump is held in place by 2 spring clips. Popped those off and the pump came right out. Put the new pump in, snapped the spring clips on, put the hose clamps back in place, the side panel and the lid. Not at all hard to do. About 30 to 45 minutes and I was doing laundry again.
Read less
Was this helpful?
Thank you for voting!
Machine would not spin. Could hear motor working
2 of 2 people
found this instruction helpful.
-
jay from carson, WA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Very easy and cheap repair. Hardest part was getting cabinet back on. Watched u tube video before and easy and quick to do take off cabinet, in clip motor and slide new motor coupler in. Put back together
Was this helpful?
Thank you for voting!