110238 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
banging noise during spin cycle, tub out of balance
8 of 9 people
found this instruction helpful.
-
Russell from CHARLTON CITY, MA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
I did the repairs after watching a few videos on this web site and it covered everything I needed. Went well and the parts were perfect.
Other Parts Used:
Was this helpful?
Thank you for voting!
Spider coupling between motor and transmission broken
9 of 12 people
found this instruction helpful.
-
Robert from Friendswood, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy rep
... Read more
air.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
I had a broken fabaric softener dispenser
7 of 7 people
found this instruction helpful.
-
Brian from Bridgewater, VA
- Really Easy
- Less than 15 mins
The dispenser ring was loose due to the broken plastic dispenser. Replacement was too easy.
Removed the old, and snapped the new one in place. Took all of 1 minute. Now I'm back up and running
Removed the old, and snapped the new one in place. Took all of 1 minute. Now I'm back up and running
Was this helpful?
Thank you for voting!
No agitation, No spin, pump OK
7 of 7 people
found this instruction helpful.
-
Ernest from Midlothian, VA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold
... Read more
the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
No parts
7 of 7 people
found this instruction helpful.
-
Jason from WENTZVILLE, MO
- Very Difficult
- More than 2 hours
A label was created and never shipped. Sat there for 2 weeks.
Contacted company for a refund and a Retha’s never been issued.
Terrible service!
Contacted company for a refund and a Retha’s never been issued.
Terrible service!
Other Parts Used:
Was this helpful?
Thank you for voting!
top agitator would not operate
8 of 11 people
found this instruction helpful.
-
Larry from Edgewood, TX
- Really Easy
- Less than 15 mins
-
Socket set
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.
Was this helpful?
Thank you for voting!
Lid Switch Screw Mounts Broke
7 of 8 people
found this instruction helpful.
-
Leo from Compton, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I had to unscrew 2 screws that held the control panel, then remove the 2 end caps, remove 2 screws that held the control panel to the washing machine. I then lifted the control panel and leaned the lower case forward. All this to get access to the ground screw for the lid mount. It sounds like a lot, but actually it was quite simple. I re
... Read more
placed the old switch with a new one and put everything back together just like new. No extra screws or parts that I could not remember where they came from. Thanks Parts Select. Reading the comments from others helped me to realize that I could do the work without worry. The only problem I had was ordering the correct part. That did not happen until I got the correct part number from the old part.
Read less
Was this helpful?
Thank you for voting!
Washer would sometimes not go into spin cycle. Opening and closing lid would put it into spin.
7 of 8 people
found this instruction helpful.
-
Donald from Toopeka, KS
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed end caps on control panel, removed two screws, lifted the control panel and rolled it back out of the way.
Undid clips and wire connection and pulled the cabinet off. Replaced the switch and put everything back together.
Easy job but helps to have two people to get the cabinet back on right.
Undid clips and wire connection and pulled the cabinet off. Replaced the switch and put everything back together.
Easy job but helps to have two people to get the cabinet back on right.
Was this helpful?
Thank you for voting!
Ground prong on power cord was broken
10 of 17 people
found this instruction helpful.
-
RONALD from PORT ORCHARD, WA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Disconnected old power cord inside control cabinet, removed strain relief , then removed damaged power cord. Reinstalled new cord with new strain relief.
Other Parts Used:
Was this helpful?
Thank you for voting!
water was overfilling
9 of 14 people
found this instruction helpful.
-
Fely from el cajon, CA
- A Bit Difficult
- 30 - 60 mins
There was a hole in the tube that connects to the water level pressure switch...so we could have just bought a new tube but we replaced the whole thing anyways. This job was easy up until we had to take the hose out and we had to remove the back cover. But works great now =-)
Was this helpful?
Thank you for voting!
Lid trigger went and fried both plug and connector
8 of 12 people
found this instruction helpful.
-
barbara from MILLVILLE, NJ
- Very Easy
- Less than 15 mins
Purchased lid trigger elsewhere but got the connector on line here after being told I would need to purchase complete wiring harness to correct. Once lid trigger was in i stripped the three wires that went to lid trigger and pushed thru the back side of the connector. Then I plugged into trigger. Now washer works again. Very easy to do.
Was this helpful?
Thank you for voting!
washer not draining
8 of 12 people
found this instruction helpful.
-
maria from san Marcos, TX
- Easy
- Less than 15 mins
-
Pliers, Screw drivers, Wrench set
but switch fixed
Was this helpful?
Thank you for voting!
Water level switch was continuously satisfied, washer would not fill, and would go into agitation immediately.
8 of 12 people
found this instruction helpful.
-
Shirley from Council Bluffs, IA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Removed the screws holding the control panel onto the washer. Removed the switch knob and then the switch (required unlocking a tab and then rotating the switch to remove). Unplugged the wiring connector and the water sensing tube. Replaced the switch in the reverse order and remounted the control panel. Test run proved the washer was w
... Read more
orking again.
Read less
Was this helpful?
Thank you for voting!
washer would walk all over when in the spin cycle
6 of 6 people
found this instruction helpful.
-
Chris from Bonners Ferry, ID
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
I tried to remove the outer console to get to the tub wear pads easier. This proved difficult for me for some reason. So I tipped the machine on its back at about a 45 degree angle. You will see the tripod support holding up the tub. The pads lie in between the bottom of the tub and on top of the tripod support . You won't be able to
... Read more
see the pads since the are on the top of the support, but you will see the two insert tabs of each pad sticking out. There are about 120 degrees apart from each other. I pushed up on the tub and slipped the piece of wood in between the tub and tripod support close to the pad. Taking a screwdriver and hammer I punched out the wear pad insert tabs. You can replace the old pad with the new one by using some force with your hands. Some pop right in and some you need to use a little leverage, maybe with the piece of wood you used to hold up the tub. Be careful not to get the pads greasy, keep clean as possible. Worked great.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The middle tub would not come out
7 of 9 people
found this instruction helpful.
-
Jayanti from SNELLVILLE, GA
- Very Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , ... Read more I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , ... Read more I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
Read less
Was this helpful?
Thank you for voting!