110230 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replacing water inlet valve with new one
5 of 5 people
found this instruction helpful.
-
David from HENRY, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The instructional video that was attached with the part I purchased was spot on with very simple instructions. The inlet valve came with a metal bracket that was not needed for my model, so just tossed it. Was completed with replacement in about 30 minutes with help from my aspiring handywoman wife (would have taken 15 minutes without her
... Read more
)
Read less
Was this helpful?
Thank you for voting!
washing machine stuck on drain cycle
17 of 41 people
found this instruction helpful.
-
Matthew from Wauwatosa, WI
- Easy
- 15 - 30 mins
-
Screw drivers
Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.
Was this helpful?
Thank you for voting!
Loud Screeching noise when draining water
5 of 5 people
found this instruction helpful.
-
Steven from Port Saint Lucie, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
On this model, no need to tip washer on back. Tilt console back and disconnect lid switch. Remove two clips holding back to top of washer (under console). Then remove top and front as directed in the video. The pump is accessible from the front of the unit, just below the tub. Hose clamps are easy to remove/replace. Took more time to
... Read more
wipe inside of washer clean than to remove/replace the water pump. Total time was just over 30 minutes.
Read less
Was this helpful?
Thank you for voting!
Water was leaking out to floor after each load
6 of 8 people
found this instruction helpful.
-
James from MILWAUKEE, WI
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Replaced the springs after watching the video's from this site and problem has been solved.
Other Parts Used:
Was this helpful?
Thank you for voting!
1. No hot water and cold water filled very slowly. 2. Washing machine severely vibrated and was very noisy.
5 of 5 people
found this instruction helpful.
-
Janice from BLUE SPRINGS, MO
- Very Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
EXACTLY as your video demonstrated.
Other Parts Used:
Was this helpful?
Thank you for voting!
counter balance spring
6 of 8 people
found this instruction helpful.
-
douglas from Angleton, TX
- Really Easy
- 30 - 60 mins
first remove your washer cabinet from unit. Next on your back left bottom is where your new spring goes. In my case my spring was broke making the washer spin out of balance. Repair with your new spring, and install cabinet back place plug it in and wash a load of cloths. Wow what a difference!!!! job took about 20 minutes. Very Happy
Was this helpful?
Thank you for voting!
drum SLAMMING into the back of the washer when sipnning
5 of 6 people
found this instruction helpful.
-
WILLIAM from DAYTON, KY
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I just replaced the spring just like the vid show me.it run's like a new one-I bought it used about 5 yr's ago
Was this helpful?
Thank you for voting!
Washing machine making a grinding noise
4 of 4 people
found this instruction helpful.
-
Tracy from Yuba City, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Purchased and installed PS1485646 COUPLING, MOTOR (Direct Drive Coupling). We googled "Washing Machine making a grinding noise. Several people suggested coupling probably broken. We located some instructions online regarding dis-assembly, sure enough,the coupling was broken. We ordered the part from Partselect.com. It arrived in three
... Read more
days, replaced the broken coupler. Washing machine back in business for around $20. Hooray! Thanks, Partselect!
Read less
Was this helpful?
Thank you for voting!
washer would not spin or agitate
6 of 10 people
found this instruction helpful.
-
Doreen from Ashtabula, OH
- Easy
- 1- 2 hours
-
Screw drivers, Socket set, Wrench (Adjustable)
I first took the 2 screws out and disconnected the wires, I got my parts ordered and when they came in I put it back together then plugged th wires back in. I really could not believe that I could do something of this nature but when I started it was easy. My boyfriend wanted to take the washer to a repair shop, but I said first I
... Read more
will take a look and see if it will be worth saving. Otherwise I will junk it. It cost me with shipping costs 41.00 I am very proud of my self.
But I read other peoples experience on fixing the same problem that I had so I gave it a try.
I will not hesitate to do other jobs myself. Doreen Finlaw
But I read other peoples experience on fixing the same problem that I had so I gave it a try.
I will not hesitate to do other jobs myself. Doreen Finlaw
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer excessive vibration during rinse spin
4 of 4 people
found this instruction helpful.
-
John from ODESSA, TX
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set
Well, after resolving Part Select (PS) shipping issues (PS sent me two refrigerator glass shelves instead of a Tub Spring); And as it turns out they sent me the wrong part for the suspension pads, which I have returned for credit. It takes 3-4 weeks to obtain your credit BTW.
Well after removing the cabinet, agitator, wash bask ... Read more et, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.
Well after removing the cabinet, agitator, wash bask ... Read more et, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The washer would drain, but was screaming while doing nothing else.
4 of 4 people
found this instruction helpful.
-
Richard from JAMESTOWN, PA
- Really Easy
- More than 2 hours
The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.
I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.
The ne ... Read more wly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.
I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.
The ne ... Read more wly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.
Read less
Was this helpful?
Thank you for voting!
My timer dial had mostly crumbled away from age.
4 of 4 people
found this instruction helpful.
-
Elizabeth from NACOGDOCHES, TX
- Very Easy
- Less than 15 mins
DO NOT WATCH THE INSTALLATION VIDEO ON WEBSITE! It's a nice video- just put me through a lot of grief because it did not apply to my washer. It is not necessary to open the control panel to pull out something at the bottom of the timer shaft(that isn't there)...or anything else requiring tools. Just UNSCREW the knob, and pull up on the ol
... Read more
d dial to remove it. Then line up the large tab on the new dial with the large cutout on shaft, and press it on. Then screw the knob back on. That's it. Finished. 5 minutes with correct instructions.
Read less
Was this helpful?
Thank you for voting!
Water would not stop when washer was filling
4 of 4 people
found this instruction helpful.
-
Michael from Mundelein, IL
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Watched the video and followed the instructions. Everything went smoothly and the repair was done in under 15 minutes, less time than it took to mop up the water when it overflowed telling me that there was a problem.
Was this helpful?
Thank you for voting!
washer shakes and was very noisey
5 of 7 people
found this instruction helpful.
-
william from lindside, WV
- Really Easy
- Less than 15 mins
researched the problem from the web-site.found the three most common things that would cause the problem.inspected the washer to see if there was evidence that one of the described parts had falled,and found that the tub wear pads were missing do to wear.simply replaced and it solved the problem. Thanks for the information.
Was this helpful?
Thank you for voting!
No Hot Water
4 of 4 people
found this instruction helpful.
-
Robert from Louisville, KY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First off, I unplugged the AC cord and disconnected the Hot and Cold water hoses. I partially removed the back of the washer with a screwdriver. There were two screws holding the control panel in place and once they were removed it simply fell forward onto the top of the machine. That allowed me to pull the back plate free and remove
... Read more
the old water inlet valve. I had to first disconnect the two AC leads from the valve along with the small hose that supplies water to the tub. The small hose had a compression clamp on it that came off with pliers. After removing the two screws that secured the valve to the back of the machine the old valve simply came out. Insallation was the reverse. I will add that when removing the controll panel there are two S shaped clips (one either side of the panel) that need to be removed using a screw driver. Be careful not to push too hard as they may fall into the machine. I also replaced both the Hot and Cold wataer hoses. All in all it was a very easy repair. I read and followed the instructions of others that posted their experience right here which was a HUGE help-thanks everyone and thanks to Part Select for the prompt delivery. I orderd the part on a Sunday and received it on Tuesday-how awesome is that?!
Read less
Was this helpful?
Thank you for voting!