110223 Kenmore Washer - Instructions

Watched a video on the internet.

Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch ... Read more and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.

Easy, just followed the repair video. Recommend also ordering the drive belt. Bought one locally during my repair.

ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned ... Read more it back up and got caught up on laundry. good day when the washer is fixed.

Replaced the gears that were eaten up, the retainer and the actuated. All parts but the spring are plastic. Did all according to your instructions. Happy to report all went well. Washer is working again.

Watched a video to get a general idea. Moved washer to garage. Raised lid, supported with s-hook and light chain. Front springs were easy, except no hole for the rod to hang in so used chain and small screwdriver through mounting hole. Back springs were not as easy. Finally removed the back panel to get to the rods. Bingo, much easier an ... Read more d only took 5 min to remove the back panel. reassemble and she works like a charm. Suggest to find a video reflecting your particular brand and model as all are similar but uniquely different. Easy project though.

Once we put in the new Water Inlet Valve, the auto sensor works now and I can wash any size load

Replaced the 4 suspension rods/springs. Only disconnect and replace one at a time. The tub will fall out if you disconnect and replace more than one rod/spring at a time.

Used video provided,but while reinstalling shocks pull the shock absorbers thru holes in washer deck using a stiff wire or a metal coat hanger will also work. This made installation so much easier!

Went on u tube saw different video to How disassemble the top to have access to the rod. Changing one by one those rod I was in need of my wife to hold the cover while I was changing the rod.... order for suspension rod kit. Reassemble the top by sliding the cover and to snap. Screw back the panel. And it solve the problem. My wife was r ... Read more eally happy so me. It can be done by anybody but first go on the internet to get a idea.

After removal of wash plate bolt. Apply Liquid Wrench oil to wash plate spline shaft. Give time for oil to penetrate. In the time it took to disassemble the motor and gearbox the oil had worked. Give the wash plate a good knock with a rubber mallet several times. After that I was able to wiggle off the wash plate by hand without breaking ... Read more anything. Be sure to pull straight up on the wash plate, any twisting or torquing will bind the spline and the wash plate wont move.
The PartSelect YouTube video was perfect for the other parts of the repair.

Removed center cap, loosened center nut, pry lightly up on center plate and tap center nut. Center plate comes loose, remove nut, remove center plate. Pry lock clip out and remove, remove screw with electric impact (screw drive will work, but slower), remove drive hub. Install new drive hub (be sure to check screw hole alignment), install ... Read more and tighten screws (be sure to follow a skip pattern and bring it down even), install lock clip, install center plate, install and tighten nut, replace center cap. Done!

This was a learning experience but it appears to have worked out in the end. Our 3 1/2 year old washer was not agitating much and I attributed that to a loose bolt. I would tighten the bolt and it would work ok for a load or two and then stop agitating. I would find that the bolt was loose again. I took a number of steps to try to get ... Read more the bolt to stay on tight - threadlock, a new bolt, more threadlock, and applying progressively more force on the bolt, with no better results. Yet the repair guys on you tube were saying the bolt only needs to be snug, not super tight - something was amiss. I even went so far as to secure the basket with a rope so I could use two hands on the socket wrench (please don't do this). But when I tried the washer again there was no agitation at all! I observed the agitation output in manual test mode and the bolt was turning in lock step with the shaft but the agitator wasn't turning at all. That's when I suspected that the problem was actually a worn lower agitator. Trouble was that now I couldn't seem to get the bolt off. Turning the wrench caused the shaft itself to rotate so I couldn't loosen the bolt from the shaft. I thought I broke the washer. Then I considered that maybe the shaft was rotating because the washer was in an agitation mode when I turned it off. I went back into manual test mode, made the washer spin, then turned it off. Fortunately, this worked. The shaft was again stationary and, albeit with great difficulty, I got the bolt off.

I removed the agitator, and as a pro would have figured out long before, the ridges inside the top of the lower agitator were almost completely worn down. I realized then that the contact between these ridges and the splines on the shaft is what is supposed to cause the lower agitator to move with the shaft. The purpose of the bolt is just to keep the agitator in the correct position and from coming off the shaft. I had been trying to compensate for the worn agitator ridges by over-tightening the bolt, creating some contact at the top of the shaft. This would work for a little while, then the agitator would start slipping, and the slipping agitator was acting just like a wrench loosening the bolt (until my stupid rope trick, that is.)

So I ordered a new agitator (only the lower agitator was bad, but the price of an entire agitator isn't a lot more than just the lower part and I was reading that the upper agitator parts will wear over time) and another new bolt (because my repeated attempts to over-tighten the first one I ordered had split the rubber gasket apart and worn the bolt head).

The new agitator fit snugly on the splines of the shaft so I sensed no need to use excessive force on the bolt. Just an easy one-handed snug tightening with the socket wrench, using the other hand to hold the lower agitator. The washer is now working again.

unfasten top from back, slide top forward and lift up, remove switch and cable (one piece), in stall new switch and cable, put top down and slide back, reinstall screws.

Changing the gear case is a basic R and R operation since the gear case is a complete assembly riveted together. It is a bit challenging though getting to it because you have to totally disassemble the entire washer nearly every nut, bolt and screw. Fortunately the washer is fairly easy to work on and I am very mechanically inclined, but ... Read more I did cheat a bit by watching some U-tube videos first. I couldn't find the same exact model washer as mine on U-tube but there were enough similar units to obtain the basic procedure. A thing I do when disassembling things is to take pictures of the way it's put together before removing stuff. It goes without saying that you first have to disconnect the power, the water hoses and it helps to get the washer out away from the wall so you can work around it. You have to remove the top, back panels, and the inner and outer tubs first. After removing the inner and outer tubs I turned the washer upside down in order to gain access to the gear case so I wouldn't have to stand on my head or lay down. Remove everything attached to the gear case (take picture) and use a strap wrench (or a strong friend) to hold the large pulley while removing the retaining nut. To remove the condenser (large round thing in black plastic retainer) rotate it counter clockwise and lift out, it doesn't snap out. I was very happy to see that the new gear case came with the shaft seal already installed so with a small amount of liquid dish soap around the outside of the rubber it allowed a nice slip fit back into the outer tub. All the parts that were removed pretty much will only fit one way so you don't have to worry too much about how everything goes back together. After reassembly and hooking up the washer again be sure to perform the calibration procedure before you turn on the water. Instructions came in the box with the gear case. Here is a side bar: I am 76, my grandson and I replaced the gear case in just a few hours, It's no big deal. Now for the interesting part, when I ordered the replacement gear case by the old part number I was told it had been superseded by a new number so when the new unit arrived I discovered that the shaft and seal looked different so hopefully the water leaking into bearing won't happen again. I was going to drill the old gear case apart and replace the bad bearing so I am glad I didn't because the shaft and seal would continue to leak and ruin the bearing again so don't try that. One thing I would like to mention about this company from which I ordered the part was the amazing delivery, only 36 hours. I ordered the part Sunday evening late and Tuesday morning early it arrived. Wow, blew me away, also I live in California and apparently the company is in Nova Scotia, no sales tax, Woo Hoo.