110222 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
my cold water did not run in the machine and it would not rinse
15 of 18 people
found this instruction helpful.
-
TONYA from DISTRICT HEIGHTS, MD
- Easy
- Less than 15 mins
-
Screw drivers
we looked at the video first then my husband fit the proble boy! was i excited! all the stores tried to get me to buy a new one. thanks partselets!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Was this helpful?
Thank you for voting!
No cold water supply/slow cold water fill
14 of 15 people
found this instruction helpful.
-
Andrew from Virginia Beach, VA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Unscrewed the two screws that hold the water lines to the valve. Unscrewed and lifted the control panel, popped the two spring clips that hold the back panel against the housing. Pulled the valve just outside the back panel. Took off the internal water line and moved it over to the new valve. Took off both hot and bold electric plugs a
... Read more
nd moved them to the new valve. With the old valve off, I sled the new valve into place and screwed it to the back panel. Put the spring tabs back on the back panel and screwed the back panel back together. Plugged it in, attached the water supply lines and tested it. Worked fine.
Read less
Was this helpful?
Thank you for voting!
Washer worked fine but wouldn't spin. Hot smell. I could turn tub by hand to help it get started and it would spin okay. Silver clutch cover was very hot to touch.
17 of 24 people
found this instruction helpful.
-
Kevin from Disputanta, VA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's
... Read more
lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.
Read less
Was this helpful?
Thank you for voting!
Screeching noise when starting the washing cycle. Especially with heavy loads.
15 of 19 people
found this instruction helpful.
-
Armando from UNION CITY, CA
- Really Easy
- Less than 15 mins
-
Socket set
The belt in this model is underneath the washing machine. Disconnect water lines and power cords, set up the drain hose in a bucket to avoid water spilling on the floor, tip the washing machine on its back, remove two bolt screws holding the plastic covering the belt, remove the old belt, and install the new one.
Was this helpful?
Thank you for voting!
Water Inlet Valve
14 of 16 people
found this instruction helpful.
-
Ron from Hibbing, MN
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The reason it took as long as it did was because the job is not in line as the work I normally do.
It would be a fairly easy job for an experienced repairman. (Taking the back off the washer was time consuming for me) The rest of the job was easy as the part was a perfect fit.
I remember having a problem blending hot/cold water ... Read more for some time. Most recently, while washing a load the water did not want to shut off. I can't remember how I diagnosed the water not shuting off as a problem along with the water temp control, but it is now repaired.
With the new valve installed, water temp select is now OK and the water now shuts off as normal.
It would be a fairly easy job for an experienced repairman. (Taking the back off the washer was time consuming for me) The rest of the job was easy as the part was a perfect fit.
I remember having a problem blending hot/cold water ... Read more for some time. Most recently, while washing a load the water did not want to shut off. I can't remember how I diagnosed the water not shuting off as a problem along with the water temp control, but it is now repaired.
With the new valve installed, water temp select is now OK and the water now shuts off as normal.
Read less
Was this helpful?
Thank you for voting!
water leaking from pump
15 of 19 people
found this instruction helpful.
-
michael from westmoreland city, PA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
Th ... Read more e corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.
Th ... Read more e corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.
Read less
Was this helpful?
Thank you for voting!
improper or no hot water flow
16 of 23 people
found this instruction helpful.
-
Cynthia from Manchester, MO
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
After taking the entire washer apart one time, we learned that we could take the top and front of the machine off only to repair it. I found Part-select online and with the model number locating the part was easy. It arrived within 3 days and with instructions I could easily replace the old part with a few tools. I spent dollars inst
... Read more
ead of hundreds for a new machine.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Noisy, clunk at end of spin cycle, spin cycle wobble, leaked
15 of 20 people
found this instruction helpful.
-
GREGG from LIVONIA, MI
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
Followed instructional video, you guys have the best repair videos!
Other Parts Used:
Was this helpful?
Thank you for voting!
Washing machine would not spin clothes, little to no agitation
13 of 14 people
found this instruction helpful.
-
Brian from APTOS, CA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Our 5 year old Kenmore washing machine broke. The first symptom was that the clothes would come out completely wet. This was due to no spin cycle. The second symptom was that the washing machine had little to no agitation. The lid still locked shut, there was no odor, and you could hear the machine running.
In the event a machi ... Read more ne does not agitate or spin, the diagnostics on this website will lead you to believe that drive hub assembly or shift actuator is the problem. The drive hub assembly is by far the more common repair (the pieces are made of plastic and are designed to wear out). If you are torn, go with the drive hub kit repair. That's what it was.
There were some surprises after carefully watching the how to video. First, the agitator in my machine was very tall and required a socket wrench extension to reach the drive hub nut. This will require two sets of hands. Second, the drive hub nut was stuck to the point where I nearly gave up. WD-40 and degreaser did not work to loosen. I ended up pouring a half teaspoon of powdered soap onto the stuck nut to get more grip on the nut. This, along with two sets of hands, got it loose. Third, calibrating machine was barely touched on in the video but this is extremely difficult, the instructions that come with the part were insufficient, and the videos on the internet are not that good. In the end, I'm not sure that the machine ever calibrated. In essence, the machine is re-calibrated by turning the switch in a specific sequence of right to left. Lights are then supposed to flash. This never did anything. I ended up opening and shutting the lid 10 times in 10 seconds as this was allegedly a way to recalibrate.
Note: 2018 and later washing machines suck because of California and the federal government rules and pressure to make them "green". Well, they don't work that well anymore as a result. Keep this in mind when you vote.
In the event a machi ... Read more ne does not agitate or spin, the diagnostics on this website will lead you to believe that drive hub assembly or shift actuator is the problem. The drive hub assembly is by far the more common repair (the pieces are made of plastic and are designed to wear out). If you are torn, go with the drive hub kit repair. That's what it was.
There were some surprises after carefully watching the how to video. First, the agitator in my machine was very tall and required a socket wrench extension to reach the drive hub nut. This will require two sets of hands. Second, the drive hub nut was stuck to the point where I nearly gave up. WD-40 and degreaser did not work to loosen. I ended up pouring a half teaspoon of powdered soap onto the stuck nut to get more grip on the nut. This, along with two sets of hands, got it loose. Third, calibrating machine was barely touched on in the video but this is extremely difficult, the instructions that come with the part were insufficient, and the videos on the internet are not that good. In the end, I'm not sure that the machine ever calibrated. In essence, the machine is re-calibrated by turning the switch in a specific sequence of right to left. Lights are then supposed to flash. This never did anything. I ended up opening and shutting the lid 10 times in 10 seconds as this was allegedly a way to recalibrate.
Note: 2018 and later washing machines suck because of California and the federal government rules and pressure to make them "green". Well, they don't work that well anymore as a result. Keep this in mind when you vote.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
F7 e1 code
12 of 12 people
found this instruction helpful.
-
Jane from WILDORADO, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Thought we needed a new shift actuator but after getting the parts and starting the replacement noticed the capacitor had come loose and was banging around under the washer. Found there was a little wire to the shift actuator that was cut probable from the capacitor being loose. spliced the wire back together and replaced the capacitor b
... Read more
ut not the shift actuator and its been working great. was an easy fix and easy to get to. Didn't need the maytag man when we can get parts from here.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Agitator moves freely in both directions
14 of 18 people
found this instruction helpful.
-
James from NAPERVILLE, AL
- Really Easy
- Less than 15 mins
-
Wrench set
First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and
... Read more
pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Read less
Was this helpful?
Thank you for voting!
water leaking during run cycle
13 of 15 people
found this instruction helpful.
-
michael from weymouth, MA
- Really Easy
- 15 - 30 mins
-
Pliers
flip machine back remove two spring clamps and hoses remove two spring clamps and water pump save $500.+on a new washer
Was this helpful?
Thank you for voting!
Washer vibrates excessively on spin cycle
13 of 15 people
found this instruction helpful.
-
Glenn from PROVO, UT
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I followed the online instructions to remove the shell and attempted to remove the drum, but not having the special wrench to remove the special nut, tried using a screwdriver and hammer, which failed to loosen the nut. I then started examining the the undercarriage and saw that I could replace the springs without removing the tub and di
... Read more
d that. In the course of replacing the springs I discovered I could also access the wear pads by lifting the drum off of the undercarriage and placing a block to hold it above the pads. I was able to pop the old pads out by tapping underneath them with a hammer. The new pads were then installed and the weight of the drum popped them in. It was necessary to lift the drum assembly three times for each of the three pads.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
would not spin properly even with new coupling
16 of 24 people
found this instruction helpful.
-
david from o, AL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Removed capscrew in end of agitator shaft took cover off machine-[ unscrewed two screws holding down control panel, hinged back, pryed retaining clips out, rocked back machine cover.]
Removed motor mounting clips and pump hoses, swinging motor and pump out of the way. Removed 3 capscrews holding transmission, pulled transmission towa ... Read more rds me removing agitator shaft, disassembled clutch assembly - removing one cirlip then another, installed new clucth parts in same order
Removed motor mounting clips and pump hoses, swinging motor and pump out of the way. Removed 3 capscrews holding transmission, pulled transmission towa ... Read more rds me removing agitator shaft, disassembled clutch assembly - removing one cirlip then another, installed new clucth parts in same order
Read less
Was this helpful?
Thank you for voting!
Lid switch broke away from top.
13 of 15 people
found this instruction helpful.
-
Brad from Wilmington, DE
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Replaceing the actual switch was easy as unscrewing two screws with the lid up. The wiring was a different story. I guess you can cut and spice and be done with it but to get to the real connection, a lot has to come apart or have very long arms to reach from the bottom. I first removed the cover to the dials by removing the side trim
... Read more
and a screw at each end near the base. That exposed the wire connection. The wire actually runs under the top therefore I had to remove the back panel partially to gain access to the wiring and holders for the wire. Just by remembering the steps while backing out, everything worked out.
Read less
Was this helpful?
Thank you for voting!