11021492310 Kenmore Washer - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Touch-Up Paint - White – Part Number: 72017
No Longer Available
Touch-Up Paint - White
★★★★★
★★★★★
(23)
Part #72017
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.
Lid Latch Assembly – Part Number: W10404050
$86.45
In Stock
Lid Latch Assembly
★★★★★
★★★★★
(32)
Part #W10404050
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
Washer Water Inlet and Valve Assembly – Part Number: WPW10683603
$97.10
In Stock
Washer Water Inlet and Valve Assembly
★★★★★
★★★★★
(19)
Part #WPW10683603
If your washer isn’t filling properly, keeps running water, or has a leak at the back, the water inlet valve might be the problem. This part controls how much hot and cold water enters the machine and helps keep the temperature balanced. It also makes sure the washer doesn’t overfill. Swapping out a worn valve can fix issues like slow fills, leaks, or uneven water temps and get your laundry routine back on track.
Washer Drain Hose – Part Number: W11244231
$37.25
In Stock
Washer Drain Hose
★★★★★
★★★★★
(4)
Part #W11244231
The drain hose carries used water from the washer to your house drain.
Lid Latch Strike – Part Number: WPW10240513
$48.35
In Stock
Lid Latch Strike
★★★★★
★★★★★
(3)
Part #WPW10240513
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, your washer door may not close properly and you may not be able to run your washer. The latch is found under the lid and can be screwed out and replaced. You will need a Phillips-head screwdriver for this repair. This part is sold individually and is and OEM part from the manufacturer.
Dryer Screw – Part Number: WP90767
$10.40
In Stock
Dryer Screw
Part #WP90767
This screw is sold individually.
Washer D-Shaped Knob Insert – Part Number: WP8536939
$15.35
In Stock
Washer D-Shaped Knob Insert
Part #WP8536939
This insert is sold individually. Knob not included. Knob is sold separately.
Lid Hinge Mounting Screw – Part Number: WPW10119828
$9.85
In Stock
Lid Hinge Mounting Screw
Part #WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
Lid Bumper – Part Number: WP9724509
$10.95
In Stock
Lid Bumper
Part #WP9724509
This gray and white washer lid bumper contains a rubber bottom and is sold individually.
Washer Hose Clamp – Part Number: WP356138
$15.07
In Stock
Washer Hose Clamp
Part #WP356138
This clamp helps to prevent leaking by holding the end of water hose in place.
Extension Hose – Part Number: 285863
$44.45
In Stock
Extension Hose
★★★★★
★★★★★
(3)
Part #285863
This part is used to extend washing machine drain hose approximately 4 feet. You may also require the connector (PartSelect Number PS334663) to connect the extension to the existing drain hose.
Lid Hinge Bearing – Part Number: WP21258
$14.99
In Stock
Lid Hinge Bearing
Part #WP21258
This is the bearing for the lid hinge. Sold individually.

Questions And Answers for 11021492310

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert - For model number 11021492310
May 5, 2023
My kenmore washer does not go into spin cycle and the lid lock light is flashing. Would this be a defective lid switch causing it not to spin?
Chris Boyle Profile
Hello Robert, thank you for the great question. The lid lock light will flash and cause the washer not to spin if the lid lock has not moved into the lock position. Be sure the lid lock and lid striker are clean, as lint or detergent buildup can block the switch and cause the flashing light. Also, check the lock striker that presses down on the lid switch. If the problem persists, you may need to replace the lid latch assembly, part number PS3497627. We hope this solves your problem!
$86.45
In Stock
Lid Latch Assembly
Was this helpful?
Thank you for voting!
Chad - For model number 11021492310
August 15, 2025
Makes a lot of noise during the spin cycle
Chris Boyle Profile
Hello Chad, thank you for getting in touch. Check the drive transmission or gear case assembly, part number PS16220910. It might be worn out or defective. They have gears in them which can fail, causing the washer to be noisy during operation. Check the clutch assembly, part number PS10057144. The clutch assembly makes the connection between the transmission and the inner tub. If the clutch or its components are worn out, the washer will make loud noises. You will also need to check the drive belt, part number PS11747978. The belt gets loose over time due to damage or wear and tear, which can cause loud noise. We hope this helps.
$53.48
In Stock
Washer Drive Pulley
$40.34
In Stock
Washer Drive Belt
$387.57
On Order
Washer Gear Case
Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the 11021492310

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Defective lid latch - Cabrio Washer
98 of 125 people found this instruction helpful.
  • William from Wakefield, RI
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this inform ation the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
Was this helpful?
Thank you for voting!
Lid would not register closed washer would not spin
30 of 38 people found this instruction helpful.
  • william from HOLLEY, NY
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Remove top of washer 5min R&R cable 20 min total time 25 min.
Was this helpful?
Thank you for voting!
Lid safety switch defective . Lid would not lock allowing washer operation.
19 of 21 people found this instruction helpful.
  • Garry from CANON CITY, CO
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Remove small screws on back of top on both sides, slide top forward. No need to remove water hoses. Lift top up to expose switch safety mechanism (black plastic) on front underside of top. Undo screws holding switch mechanism. remove plate cover from back of top and unplug wiring harness. Thread new wireing harness and plug through hole in top and plug in to plug receptor.
Was this helpful?
Thank you for voting!