11021392013 Kenmore Washer - Instructions

All Instructions for the 11021392013
16 - 24 of 24

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
spin cycle did not activate
2 of 4 people found this instruction helpful.
  • Enrique from Miami Shores, FL
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having w asher door bang shut.Took longer than expected, but each procedure was simple.
Was this helpful?
Thank you for voting!
Washer would go into the cycle to rinse dry.
1 of 2 people found this instruction helpful.
  • Daniel from WARMINSTER, PA
  • Really Easy
  • 30 - 60 mins
  • Socket set
Replacing the part was fairly easy. However it did not resolve the problem. The spin cycle did not activate,leaving my washer full of water. We ordered another Maytag Washer. Hopefully this one doesn't break down for a long time.
Was this helpful?
Thank you for voting!
door latch broke
0 of 1 people found this instruction helpful.
  • Diana from Chimacum, WA
  • Easy
  • 15 - 30 mins
  • Nutdriver
Figuring out how to take the lid off was the hard part. Took out the old and replaced with new and put lid back on and rehooked up.
Was this helpful?
Thank you for voting!
Replace drain hose
3 of 11 people found this instruction helpful.
  • Brian from DREXEL HILL, PA
  • Easy
  • 30 - 60 mins
  • Pliers
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this helpful?
Thank you for voting!
The lid lock switch on our clothes washer went out
  • Steven from Keenesburg, CO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I had to remove 3 screws from the back of the washer to be able to lift the top. Then remove 3 screws under the lid which held the switch in, unplug the old part and put the new one in. It was quite sinple. The most difficult part was figuring out you have to slide the top of the washer forward a bit to be able to tilt it up.
Was this helpful?
Thank you for voting!
Bad latch lock
  • David B from Madison, IN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Took the back of the control panel off, lifted the top of the washing machine up took off nuts holding the latch lock off, installed the new parts put back together. Piece of cake...because i got the right parts the first time. Thank you PartSelect.
Was this helpful?
Thank you for voting!
would not unlock
  • Michael from Lincoln, RI
  • Easy
  • 15 - 30 mins
  • Screw drivers
Disassembled ,as assembled.
Was this helpful?
Thank you for voting!
Lid lock would not ingague.
  • Tom from Franklin, IN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Removed two brackets on back top of washer that hold top secure. Pulled top forward and up off off pins located on front top of washer. Located switch removed two screws holding it in. Then removed Panel on back of top in order to get to controls and unplugged other end of switch. Then reversed procedure and waher was back in service.
Was this helpful?
Thank you for voting!
Missing lid hinge bearing
  • Kim from Oviedo, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid an d into bushing. 5)Reinstall hinge pin retaining screws and tighten.
Was this helpful?
Thank you for voting!
All Instructions for the 11021392013
16 - 24 of 24