110212 Kenmore Washer - Instructions

All Instructions for the 110212
16 - 30 of 423

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lid safety switch defective . Lid would not lock allowing washer operation.
19 of 21 people found this instruction helpful.
  • Garry from CANON CITY, CO
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Remove small screws on back of top on both sides, slide top forward. No need to remove water hoses. Lift top up to expose switch safety mechanism (black plastic) on front underside of top. Undo screws holding switch mechanism. remove plate cover from back of top and unplug wiring harness. Thread new wireing harness and plug through hole in top and plug in to plug receptor.
Was this helpful?
Thank you for voting!
My washer lid lock light kept blinking and the washer would not start
17 of 18 people found this instruction helpful.
  • Janice from GREENVILLE, NC
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
I followed the online video, removed the old part and replaced it with the new part. My washer is working perfectly. It took about an hour to reset.
Was this helpful?
Thank you for voting!
Making loud noises.
21 of 30 people found this instruction helpful.
  • Roy from BROOKLYN, NY
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you
Was this helpful?
Thank you for voting!
Top Half of Agitator would not function without appying sideways pressure
18 of 21 people found this instruction helpful.
  • Donald from Fredericksburg, VA
  • Really Easy
  • 15 - 30 mins
  • Socket set
Heard about the website... 1 minute to find it, 10 minutes to order new cogs... 3 day wait for new parts... Rec'd Fedex, 15 minutes total to pull the agitator cover (bleach dispenser) then the bung cover with o-ring (just lift out) expose bolt, unskrew and remove top portion of agitator or entire agitator if it's easier. Seperate, remo ve black cog holder (slides up the spindle) and replace cogs one at a time just like the old ones. Reassemble in reverse and you are back in business. Saved the $75 deductible on my home appliance warrenty. You guys are the best... cheers...
Was this helpful?
Thank you for voting!
Agitator was barely agitating. Making a clicking noise.
17 of 18 people found this instruction helpful.
  • Charmaine from Slidell, LA
  • Easy
  • 15 - 30 mins
  • Socket set
Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.
Was this helpful?
Thank you for voting!
Smelled a burning odor occasionally
17 of 23 people found this instruction helpful.
  • Paul from E NORTHPORT, NY
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Socket set, Wrench (Adjustable)
First, I checked the belt before ordering and then decided to order the belt, capacitor, and clutch assembly (if I needed to replace). I replaced the belt noticing the older belt came right off and new one was tighter going on. I replaced the capacitor since I had it handy and it can be known to cause this smell also. After setting wash er back up and started a cycle I noticed the spin cycle would not start properly so I thought maybe the capacitor (new one) was faulty or just not the exact match even though it was said to be. I replaced my older capacitor back on and again ran cycle and it ran great. Thus I decided to send the parts which were not used. I would recommend this site as I have used them in the past before on other items. They ship fast and have a great return policy if parts not used.
Was this helpful?
Thank you for voting!
Washer lid would not release
18 of 26 people found this instruction helpful.
  • Michael from BURLINGTON, NJ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Unplug washer. Remove 4 screws from the small plates that hold top to body of washer. Remove cover plate from back of top. Lift top from base and support it on its back. Remove lid lock mechanism. Unplug connector from its socket at the back of the lid. In reverse order install the new lid latch,
Was this helpful?
Thank you for voting!
Agitator moves freely in both directions
14 of 18 people found this instruction helpful.
  • James from NAPERVILLE, AL
  • Really Easy
  • Less than 15 mins
  • Wrench set
First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Was this helpful?
Thank you for voting!
Banging all the time during rinse as if its out of balance
14 of 18 people found this instruction helpful.
  • christine from SWANSEA, MA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Followed the video, no need to add. Worked perfectly!
Was this helpful?
Thank you for voting!
Washer shook violently during spin cycle
12 of 12 people found this instruction helpful.
  • Bobby from LAGRANGE, OH
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Raise top cover, remove tub ring.
Remove suspension rods one at a time by pulling the
rods upward, remove keepers at top,pulled rods out the bottom by tilting washer. Replaced all four rods and installed load centering springs which hadn't been installed from factory. Took 1/2 hour and works like a new one??
Was this helpful?
Thank you for voting!
lid would not lock, washer would not run...
12 of 13 people found this instruction helpful.
  • John from Hale Center, Texas, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed old striker ( 2 Phillips head screws ) replaced with new striker with the 2 screws and was done, easy fix...
Was this helpful?
Thank you for voting!
Water inlet nozzle was stripped and leak
24 of 50 people found this instruction helpful.
  • Armand from WESTPORT, MA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Remove the front panel and back panel unplug the part unscrewed the part and replace it with the new one
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people found this instruction helpful.
  • Michelle from Richardson, TX
  • Really Easy
  • Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
squeal and chirping while in risne / spin mode
10 of 10 people found this instruction helpful.
  • Thomas from GRAIN VALLEY, MO
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
Was this helpful?
Thank you for voting!
Hot water valve would barely open - take 35 mins to fill washer
10 of 11 people found this instruction helpful.
  • Kevin from ARLINGTON, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Pull the washer out from wall
Unplug the Washer
Close the supply line valves
Unscrew the supply lines, use bucket to catch line water
Remove 1 cover plate for elec lines (1 screw)
Remove 2 screws on edge of back plate for control panel
Slide long blade under front of control panel corners, pop the lock clips< br />Lay control panel forward - controls down
Compare new and old part - looks the same, wires, etc
Remove center screw on back plate cover to remove it
Unplug the elec wires connecting the valves and the control panel
Remove 2 screws holding the water valve outlet
swap out the old values for new valves
Reverse the process - step backwards and reassemble
Took me 36 minutes.
Tested the washer for Hot fill and later cold - both work
Was this helpful?
Thank you for voting!
All Instructions for the 110212
16 - 30 of 423