1102091 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water Pump was leaking
9 of 13 people
found this instruction helpful.
-
Rick from Liberty, SC
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.
I turned the washer on its side and felt where the leak was on th ... Read more e pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.
I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!
I turned the washer on its side and felt where the leak was on th ... Read more e pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.
I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
top agitator would not operate
8 of 11 people
found this instruction helpful.
-
Larry from Edgewood, TX
- Really Easy
- Less than 15 mins
-
Socket set
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.
Was this helpful?
Thank you for voting!
Ground prong on power cord was broken
10 of 17 people
found this instruction helpful.
-
RONALD from PORT ORCHARD, WA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Disconnected old power cord inside control cabinet, removed strain relief , then removed damaged power cord. Reinstalled new cord with new strain relief.
Other Parts Used:
Was this helpful?
Thank you for voting!
Lid Switch Screw Mounts Broke
7 of 8 people
found this instruction helpful.
-
Leo from Compton, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I had to unscrew 2 screws that held the control panel, then remove the 2 end caps, remove 2 screws that held the control panel to the washing machine. I then lifted the control panel and leaned the lower case forward. All this to get access to the ground screw for the lid mount. It sounds like a lot, but actually it was quite simple. I re
... Read more
placed the old switch with a new one and put everything back together just like new. No extra screws or parts that I could not remember where they came from. Thanks Parts Select. Reading the comments from others helped me to realize that I could do the work without worry. The only problem I had was ordering the correct part. That did not happen until I got the correct part number from the old part.
Read less
Was this helpful?
Thank you for voting!
Washer would sometimes not go into spin cycle. Opening and closing lid would put it into spin.
7 of 8 people
found this instruction helpful.
-
Donald from Toopeka, KS
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed end caps on control panel, removed two screws, lifted the control panel and rolled it back out of the way.
Undid clips and wire connection and pulled the cabinet off. Replaced the switch and put everything back together.
Easy job but helps to have two people to get the cabinet back on right.
Undid clips and wire connection and pulled the cabinet off. Replaced the switch and put everything back together.
Easy job but helps to have two people to get the cabinet back on right.
Was this helpful?
Thank you for voting!
water was overfilling
9 of 14 people
found this instruction helpful.
-
Fely from el cajon, CA
- A Bit Difficult
- 30 - 60 mins
There was a hole in the tube that connects to the water level pressure switch...so we could have just bought a new tube but we replaced the whole thing anyways. This job was easy up until we had to take the hose out and we had to remove the back cover. But works great now =-)
Was this helpful?
Thank you for voting!
The middle tub would not come out
7 of 9 people
found this instruction helpful.
-
Jayanti from SNELLVILLE, GA
- Very Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , ... Read more I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , ... Read more I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
Read less
Was this helpful?
Thank you for voting!
washer wouldn't spin with load, then not at all with rapid clicking sound
6 of 6 people
found this instruction helpful.
-
Lou from ATLANTIC HLDS, NJ
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Clutch was noticibly worn compared to new part. Direct drive flange had broken, this part should be steel. found a you tube video that was simple to follow. no problems
Other Parts Used:
Was this helpful?
Thank you for voting!
Lid trigger went and fried both plug and connector
8 of 12 people
found this instruction helpful.
-
barbara from MILLVILLE, NJ
- Very Easy
- Less than 15 mins
Purchased lid trigger elsewhere but got the connector on line here after being told I would need to purchase complete wiring harness to correct. Once lid trigger was in i stripped the three wires that went to lid trigger and pushed thru the back side of the connector. Then I plugged into trigger. Now washer works again. Very easy to do.
Was this helpful?
Thank you for voting!
washer not draining
8 of 12 people
found this instruction helpful.
-
maria from san Marcos, TX
- Easy
- Less than 15 mins
-
Pliers, Screw drivers, Wrench set
but switch fixed
Was this helpful?
Thank you for voting!
washer would walk all over when in the spin cycle
6 of 6 people
found this instruction helpful.
-
Chris from Bonners Ferry, ID
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
I tried to remove the outer console to get to the tub wear pads easier. This proved difficult for me for some reason. So I tipped the machine on its back at about a 45 degree angle. You will see the tripod support holding up the tub. The pads lie in between the bottom of the tub and on top of the tripod support . You won't be able to
... Read more
see the pads since the are on the top of the support, but you will see the two insert tabs of each pad sticking out. There are about 120 degrees apart from each other. I pushed up on the tub and slipped the piece of wood in between the tub and tripod support close to the pad. Taking a screwdriver and hammer I punched out the wear pad insert tabs. You can replace the old pad with the new one by using some force with your hands. Some pop right in and some you need to use a little leverage, maybe with the piece of wood you used to hold up the tub. Be careful not to get the pads greasy, keep clean as possible. Worked great.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer would not work in agitate or spin cycle
6 of 6 people
found this instruction helpful.
-
yesenia from apopka, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off wit
... Read more
hout unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.
The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.
It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.
The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.
It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.
Read less
Was this helpful?
Thank you for voting!
loud noise during spin cycle, then not spinning at all
6 of 7 people
found this instruction helpful.
-
William from CHESHIRE, CT
- Really Easy
- 1- 2 hours
-
Pliers, Screw drivers, Wrench set
Watching videos identified what parts to purchase.
Once identified - WATCH EACH PARTS VIDEO (again).
Lessons learned:
1) better to NOT tilt the washer
2) watch (more than once) and learn from the videos
3) must difficult step was loosening the tub retaining nut without having a spanner wrench (used a hammer and a ... Read more short / wide blade screwdriver)
4) ended up being the tub support was not sitting properly in the suspension plate
5) cleaned and changed parts while apart
6) running as good as new
Thanks!!
Once identified - WATCH EACH PARTS VIDEO (again).
Lessons learned:
1) better to NOT tilt the washer
2) watch (more than once) and learn from the videos
3) must difficult step was loosening the tub retaining nut without having a spanner wrench (used a hammer and a ... Read more short / wide blade screwdriver)
4) ended up being the tub support was not sitting properly in the suspension plate
5) cleaned and changed parts while apart
6) running as good as new
Thanks!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
broken lid switch
6 of 7 people
found this instruction helpful.
-
Gary from Stuart, FL
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
I unplugged the machine.
Removed the back panel.
Located the switch, removing it and then following the wire to the plug, unplugging it.
replaced with new switch, plugged it in and replaced the back panel.
Removing and putting the back panel back was the hardest part.
Removed the back panel.
Located the switch, removing it and then following the wire to the plug, unplugging it.
replaced with new switch, plugged it in and replaced the back panel.
Removing and putting the back panel back was the hardest part.
Was this helpful?
Thank you for voting!
Washer not agitating
7 of 10 people
found this instruction helpful.
-
Keith from Erie, CO
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I looked for a youtube video on how to repair the lid switch. The video was very good but was filmed in a perfect world. My washer sits in a somewhat confined area so getting the outside skin put back perfectly was a bit tricky.
Was this helpful?
Thank you for voting!