11020242510 Kenmore Washer - Instructions

All Instructions for the 11020242510
46 - 60 of 67

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
out of balance
2 of 2 people found this instruction helpful.
  • Charles from ARVADA, CO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
The info. was really helpful
Was this helpful?
Thank you for voting!
The cold water side of the inlet wasn’t working.
2 of 2 people found this instruction helpful.
  • Valerie from FRANKFORT, KY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I figured out through the process of elimination that the problem was the rubber plunger that the solenoid opens and closes. I couldn’t fix just the plunger so I replaced the whole water inlet valve and the cold water worked perfectly after that. Even though it was a little tough to diagnose the problem it was very easy to replace the par t once I found out what it was that was wrong.
Was this helpful?
Thank you for voting!
Loud banging during spinning
3 of 5 people found this instruction helpful.
  • Tom from LONG BEACH, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlp ool washers!
Was this helpful?
Thank you for voting!
machine wobbled violently
2 of 2 people found this instruction helpful.
  • John from TEXAS CITY, TX
  • Really Easy
  • 30 - 60 mins
followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.
Was this helpful?
Thank you for voting!
Wouldn't fill with water.
2 of 2 people found this instruction helpful.
  • Wes from WARRIOR, AL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Part fixed it perfectly.
Was this helpful?
Thank you for voting!
Not really a problem but the hardest part was moving the washer to lay on its back.
2 of 2 people found this instruction helpful.
  • John from WHITEWATER, CA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Socket set, Wrench (Adjustable)
I simply followed Steve's instructions on video. Very easy repair. Washer works great, no jumping or vibrating.
Was this helpful?
Thank you for voting!
Washer hoses due for replacement
3 of 5 people found this instruction helpful.
  • James from PINE MOUNTAIN, GA
  • Easy
  • 30 - 60 mins
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this helpful?
Thank you for voting!
agitator broke
2 of 3 people found this instruction helpful.
  • Joseph from Kalkaska, MI
  • Really Easy
  • Less than 15 mins
  • Socket set
very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast
Was this helpful?
Thank you for voting!
Hot water inlet was cracked
1 person found this instruction helpful.
  • daryl from Madison, TN
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Remove power and hoses. Remove five 1/4” hex head screws on back plate. Top control panel can be removed by inserting putty knife into front right and left corners of control panel. Push with enough force while lifting corners. Clips are metal so you won’t break them. Lay the control panel toward washer lid.
Two screws hold the wate r inlet in place but remove cables from inlet valves and the cable in the middle which has a temperature sensing thermistor. Once the 2 screws are removed you can manipulate the assembly out of its slot. After new assembly installed with cables reconnected and screws in place align the plastic control panel tabs back in that are at the rear of the top before snapping the control panel back into position.
Was this helpful?
Thank you for voting!
Washer drum banging on spin cycle
1 person found this instruction helpful.
  • David from KISSIMMEE, FL
  • Really Easy
  • 15 - 30 mins
Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!
Was this helpful?
Thank you for voting!
Banging when in spin cycle.
1 person found this instruction helpful.
  • ROBERT from OXLY, MO
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.
Was this helpful?
Thank you for voting!
The washer was shaking during the spin cycle
1 person found this instruction helpful.
  • Michele from ROCHESTER, NY
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
Exactly like the video from the website
Was this helpful?
Thank you for voting!
Washer would start bouncing during the spin cycle.
1 person found this instruction helpful.
  • Richard from Buda, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
I followed the instructions on the website video. (excellent video) It took me a little while to pull the springs up into position but overall, the install went very well. I have not had any issues with the washer since then.
Was this helpful?
Thank you for voting!
Shakes and moves | Noisy
1 person found this instruction helpful.
  • Philip from BURIEN, WA
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
Followed video on your web site, and used that for ways to fix, good directions. If I was more organized it prob would of taken about an hour or less
Was this helpful?
Thank you for voting!
spin cycle did not activate
2 of 4 people found this instruction helpful.
  • Enrique from Miami Shores, FL
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having w asher door bang shut.Took longer than expected, but each procedure was simple.
Was this helpful?
Thank you for voting!
All Instructions for the 11020242510
46 - 60 of 67