11020022011 Kenmore Washer - Instructions

All Instructions for the 11020022011
106 - 120 of 460

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced cogs in agitator
2 of 3 people found this instruction helpful.
  • Allen from Simpsonville, KY
  • Really Easy
  • Less than 15 mins
Fabric softener dispenser simply lifts off the top of the agitator. Then, a flat head screwdriver, tucked anywhere under the edge of the cap, lifts/pries it off. Then drop a 1/2" drive extension(no socket as it simply is the extension itself) into the plastic "nut" and remove it while holding onto bottom of agitator with your other hand. Lift it out, replace the cogs and reverse for reassembly. Total time less than 5 minutes, including shipping was $10.50 for cogs - repair #4 completed thanks to the fine folks at PartSelect! PS - part arrived at my door less than 24 hrs after ordering it even tho I requested 2-3 day shipping.
Was this helpful?
Thank you for voting!
agitator broke
2 of 3 people found this instruction helpful.
  • Joseph from Kalkaska, MI
  • Really Easy
  • Less than 15 mins
  • Socket set
very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast
Was this helpful?
Thank you for voting!
the top section of the agitator would not turn
2 of 3 people found this instruction helpful.
  • joseph from san antonio, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.
Was this helpful?
Thank you for voting!
Agitator would not agitate
2 of 3 people found this instruction helpful.
  • Daniel from Beaufort, SC
  • Really Easy
  • Less than 15 mins
  • Pliers, Socket set
Removed the agitator with a socket wrench and replaced cogs as directed in repair video.
Was this helpful?
Thank you for voting!
Top part of agitator not working
2 of 3 people found this instruction helpful.
  • Roger from St. Albans, WV
  • Easy
  • Less than 15 mins
  • Nutdriver
I used a nut driver to remove the screw that held the to part of the agitator onto the bottom part. I then took out the worn out directional cogs and replaced them with new ones and re-assembled the agitator and was back in business. The agitator now works the way it should. Easy fix. The only negative part of this experience was that the shipping was twice as expensive as what the parts cost. Very fast shipping from PARTS SELECT .
Was this helpful?
Thank you for voting!
Top Agitator would turn
2 of 3 people found this instruction helpful.
  • EDWARD from CATONSVILLE, MD
  • Easy
  • Less than 15 mins
  • Socket set
First, I unscrewing the single bolt which keeps the two part agitator in place (agitator bolt). Second, I pulled the entire agitator out from the machine. third, I then seperated the top and bottom parts of the agitator. forth, I removed the old worn out "Agitator Direction Cogs". Fifth, I then inserted the new Agitatpr Direction Co gs"s. Six, I reassembling the top and bottom parts of the agitator. Seven, I reinstalled the reassembled agitator back into the machine. Eight, after inserting and tighting up the agitator bolt with a socket rench, and tured the machine on, it work like it was new again. .
Was this helpful?
Thank you for voting!
Broken agitator dogs
2 of 3 people found this instruction helpful.
  • Larry from Aloha, OR
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Pop the cap on the agitator with a screwdriver then take out the bolt underneath. Replace the agitator dogs.

When putting the bolt back, don't tighten like its going to jump out of the washer. I think that's why I had to replace it a second time
Was this helpful?
Thank you for voting!
My Machine Wasn't Agitating... Which Was Agitating Me!
2 of 3 people found this instruction helpful.
  • mary from hallandale, FL
  • Really Easy
  • 15 - 30 mins
  • Socket set
It was really easy. I popped off the agitation cone cover, used a socket set to remove the bolt which holds it all together. I removed the broken part, assembled the new one, using the old one as a example. I installed the new one. . . And I have clean clothes again. So much better to fix the old machine then buy a new one. . .
Was this helpful?
Thank you for voting!
The top agitator wasn't turning.
2 of 3 people found this instruction helpful.
  • Daniel from Susquehanna, PA
  • Really Easy
  • Less than 15 mins
  • Socket set
I found the Agitator "dogs" (really that's their name) to be stripped. Ordered the part and got it within two days. It was a very easy fix and the old washer works great now.
Was this helpful?
Thank you for voting!
Top Of Agitator Was Not Engaging
2 of 3 people found this instruction helpful.
  • RANDI from APACHE JUNCTION, AZ
  • Really Easy
  • 15 - 30 mins
  • Socket set
1St I took the top cap from the agitator, I then removed the middle cap. I then removed the 7/16th bolt from the middle of the agitator and removed the agitator. I took the old broken parts out and replaced them with the new parts. I then put everything back together in the reverse order tried the washing out and it works great. Actua lly I just followed the instructions, which took 20 minutes, and everything was kopacetic.
Was this helpful?
Thank you for voting!
Agitator stopped turning
1 person found this instruction helpful.
  • William from Canandaigua, NY
  • Easy
  • 15 - 30 mins
  • Socket set
I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.
Was this helpful?
Thank you for voting!
Dogs worn on agitator
1 person found this instruction helpful.
  • Kenneth from Muncie, IN
  • Really Easy
  • 15 - 30 mins
  • Socket set
Removed top of agitator, then removed the nut holding the agitator in place, pulled up the second piece of the agitator, replaced dogs and put the agitator back together
Was this helpful?
Thank you for voting!
The top of the agitator no longer would engage, the little ears were stripped
1 person found this instruction helpful.
  • Charles from Mechanicsville, MD
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I pulled the top off ( the fabric softner dispenser) unscrewed the nut pulled up on the agitator replaced the ears put it back together. . It works just as good as a $75.00 an hour repairman could have done. And the wife wanted a new washer? Ha
Was this helpful?
Thank you for voting!
The washer quit agitating
1 person found this instruction helpful.
  • Jeff from Michigan City, IN
  • Really Easy
  • 15 - 30 mins
  • Socket set
I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the re pair man.
Was this helpful?
Thank you for voting!
agitator weak, hardly turning
1 person found this instruction helpful.
  • paul from mount Juliet, TN
  • Really Easy
  • 15 - 30 mins
  • Socket set
took the cover off the top of agitator, removed 3/8" bolt that went through cam and secured agitator. removed agitator and replaced the 4 agitator dogs and cam.
replaced agitator, tightened bolt, replaced cover. the washer works like new again? thankyou for your help and the correct parts.
Was this helpful?
Thank you for voting!
All Instructions for the 11020022011
106 - 120 of 460