- Home
- 11020022011
- Instructions
11020022011 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lid wouldn't lock
4 of 4 people
found this instruction helpful.
-
James from INDIAN LAKE, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed 5 screws on back, released 2 retention clips on front, lifted top of washer to expose lock assembly, removed 2 screws holding lock assembly in place followed electrical line back to plug behind control panel plugged new lock in, and reassembled in reverse order. Done!
Was this helpful?
Thank you for voting!
Making a loud noise for a while then stopped spinning
4 of 4 people
found this instruction helpful.
-
Lucas from ARKANSAS CITY, KS
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this helpful?
Thank you for voting!
I noticed that in the spin cycle the machine did not sound like it was suppose to. So I took the time and watched it go thru the steps and saw that it was not spinning.
4 of 5 people
found this instruction helpful.
-
Fernando from Houston, TX
- Really Easy
- Less than 15 mins
-
Socket set
Went on line and ordered the piece I need. I got my socket set out, held the center piece in place then with the socket unscrewed the bolt. Popped the plastic washer off put the agitator clips in, put the plastic washer on and bolted it back together and was done. Easy as 1, 2, and 3.
Was this helpful?
Thank you for voting!
making noise when starting spin cycle
4 of 5 people
found this instruction helpful.
-
JERRY W. from CARROLLTON, GA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Watch video on the site and the insulation will be easy and take about 30 min.
Was this helpful?
Thank you for voting!
Washer was making an awful screeching noise when agitating
3 of 3 people
found this instruction helpful.
-
Kristy from Lebanon, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this helpful?
Thank you for voting!
washer shaking
3 of 3 people
found this instruction helpful.
-
Oralia from DALLAS, TX
- Easy
- 30 - 60 mins
-
Pliers
the repair went well but I still haven't received a refund for the order was was sent incorrectly. Order #22085769 order date 2/3/23
Was this helpful?
Thank you for voting!
Washer walking during spin cycle
3 of 3 people
found this instruction helpful.
-
Tricia from HARLEYSVILLE, PA
- Easy
- 30 - 60 mins
-
Socket set
Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF ... Read more I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF ... Read more I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
Read less
Was this helpful?
Thank you for voting!
Actuator clicking not going into spin mode
3 of 3 people
found this instruction helpful.
-
Courtney from Hollis, NH
- Easy
- 30 - 60 mins
-
Pliers, Socket set
I laid the washer on its front side to access underneath. I removed the original washer pulley system and actuator very easily to replace them with the new parts. The new/updated model actuator for my machine was a little bit challenging to maneuver around existing parts to make work, but I eventually got it installed. The plug was angled
... Read more
very differently than the original plug on the actuator, but it was a tight fit. There was no issue installing the washer pulley system. Hooked washer back up to power, water lines, drain line, and the washer has been working perfectly since.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
washer would not spin on wash cycle
3 of 3 people
found this instruction helpful.
-
Kim from MOUNT UNION, PA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
My daughter is the handy one in the family. She followed Steve's video installation steps and in an hour i was washing clothes.
Was this helpful?
Thank you for voting!
Burning smell, ASSUMED it was the belt
4 of 6 people
found this instruction helpful.
-
James from MAHWAH, NJ
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!
Was this helpful?
Thank you for voting!
Washer -Maytag Centennial- would NOT agitate. It would run through all cycles as indicated by the lights and even spin at the end, but never agitated. It also did not appeared to go into "sensing" mode at the start. Took a long time to move from "sensing" light to "wash" light. Did not hear or see a
3 of 3 people
found this instruction helpful.
-
Maxwell from RINGWOOD, NJ
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
There are a number of videos showing how to do this repair:
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut dri ... Read more ver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.
I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut dri ... Read more ver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.
I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.
Read less
Was this helpful?
Thank you for voting!
Broken agitator top section...
3 of 3 people
found this instruction helpful.
-
Dan from GREAT FALLS, MT
- Really Easy
- Less than 15 mins
-
Socket set
Removed softener cup agitator cap and one bolt, lifted agitator out and replaced with new one... tightened bolt replaced cap and softener cup and away we go, done...
Was this helpful?
Thank you for voting!
washer was draining but no spinning
3 of 3 people
found this instruction helpful.
-
JOSE from MILLBURY, MA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Disconnect electrical plug from the wall, disconnect drain hoses and tip washer forward remove belt hosing basket and then remove the electrical plug that contains seven wires connected to actuator then remove the two small screws.
Then reverse the operation to stall the new part. Very easy.
Then reverse the operation to stall the new part. Very easy.
Was this helpful?
Thank you for voting!
Did not Agitate, spun freely.
4 of 6 people
found this instruction helpful.
-
Todd from hampstead, NC
- Easy
- Less than 15 mins
-
Socket set
Used screw driver to pop top off to access the bolt on spinning unit.Used socket wrench and took bolt off of bottom of spinniner. Replace agitater with new parts and reassembled. Now it works like new.
Was this helpful?
Thank you for voting!
upper Agitator not working
3 of 3 people
found this instruction helpful.
-
Edward from Grand Blanc, MI
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
undo one bolt and change agitator kit
Was this helpful?
Thank you for voting!