- Home
- 1069750680
- Instructions
1069750680 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
the ice maker quit producing ice.
5 of 5 people
found this instruction helpful.
-
darryl from little york, IL
- Easy
- 30 - 60 mins
-
Nutdriver
I removed 1 bottom screw and 2 upper screws useing a 1/4 inch socket nut driver. then useing a flat edge screwdriver i incerted in slot to remove wiring cluster. to install just reverse process. you maye have to cut u-shape slot for water spout to sit in.
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people
found this instruction helpful.
-
Carl from RIVERSIDE, CA
- Very Difficult
- More than 2 hours
-
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
ice tray was leaking water
5 of 5 people
found this instruction helpful.
-
Brenda from Henderson, NV
- Really Easy
- Less than 15 mins
-
Nutdriver
Unplugged wire, loosened two screws on top took out lower screw.Lifted the ice maker up and out it came. The wiring that came with the new part was to short so we unplugged ours from the old part and used it:) was really easy and works great now no leaks
Was this helpful?
Thank you for voting!
Refrigerator had shut down
7 of 11 people
found this instruction helpful.
-
Ronald from Martinsville, IL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Went on line ,ordered part on Friday afternoon ,Fedex was at my house Saturday Morning,,THIS SERVICE IS GREAT ,,THANK YOU VERY MUCH FOR BEING SO FAST
Was this helpful?
Thank you for voting!
The Switch Broke...Absolutely Fell Apart.
5 of 5 people
found this instruction helpful.
-
Duncan from Metairie, LA
- Really Easy
- Less than 15 mins
-
Screw drivers
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Was this helpful?
Thank you for voting!
Fridge would not defrost creating ice buildup and fridge would then get warm
7 of 11 people
found this instruction helpful.
-
Susan from Madrid, NY
- Really Easy
- 15 - 30 mins
My brother came up and installed the part.
Was this helpful?
Thank you for voting!
Noisey Blowerfan and Broken Air Tower
5 of 6 people
found this instruction helpful.
-
Patrick from WALPOLE, MA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
Watched your video on how to replace the evaporator fan motor. Took apart the freezer and replaced the fan motor with blade. It was a little tight getting all the harnessing back into the space but I did it. It would have been nice to see a video to put everything back but I did it and replaced the air tower with no problem. The end r
... Read more
esult is my freezer evaporator fan motor with blasé is a lot quitter now. Thanks
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Freezer would periodically allow things to partially thaw out
5 of 6 people
found this instruction helpful.
-
Dana from Canyon Lake, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
First, I removed the two thermostat knobs, then the snap-on plastic cover. Then, I removed the 4 screws holding the housing for the timer, thermostats, etc., and dropped it down enough to remove the timer and the wiring harness going into it. Installing the new one was the same process, in reverse. Quite simple!
Was this helpful?
Thank you for voting!
Icemaker just stopped making ice one night
8 of 15 people
found this instruction helpful.
-
Robert from Center Moriches, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
I pulled the refrigerator out from the wali slowly so not to damage the water line to the ice maker. Then with a nut driver I removed all the screws holding the back plate on. Being careful not to kink the water line, I used the adjustable wrench to losen the water line feed nut and the nut that goes to the line to the icemaker. Then I re
... Read more
moved the screws holding the valve in place finished unhooking the water lines with my fingers. I then got the new valve and finger tightend the main water supply nut to the inlet side, then I pushed the plastic supply tube going to the icemaker into the valve. The new valve does not use a nut to attach the tubing it is a presure fit very easy.
Read less
Was this helpful?
Thank you for voting!
freezer constantly covered with ice not defrosting
7 of 12 people
found this instruction helpful.
-
michael from millstone, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
I opened rear wall inside freezer (two screws) cut the wires on old thermostat and removed it. Then I attatched the new thermostat to the existing wires using wire nuts and electrical tape and slid it onto the copper tubing. Re-installed the rear wall. Freezer works like a charm and the refridgerator is also colder. Job completed in twent
... Read more
y minutes and Tim Allen has nothing on me. Mike Milne
Read less
Was this helpful?
Thank you for voting!
Freezer was dripping water into refrigerator below
5 of 6 people
found this instruction helpful.
-
John from Redmond, WA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed the old timer from the housing. The replacement came with good instructions. I followed the instructions corresponding to the color wires in my unit. The first time it was installed, the fridge did not come on and the temperature rose after a couple hours. Looked at the part and realized the defrost cycle must have kicked in. Need
... Read more
ed to slightly turn the gray slotted part to initiate the timer so it would stop the defrost and start the fridge. That did it! It must have advanced the timer so it could accumulate run time. Whole repair saved us $3000 in a new fridge.
Read less
Was this helpful?
Thank you for voting!
Lower Light Socket removed and Wires capped with wire nuts
6 of 9 people
found this instruction helpful.
-
Wayne from Arlington, TX
- A Bit Difficult
- Less than 15 mins
My tenants moved out of my rental property and abandoned their refrigerator there. The freezer door would not close properly because someone had previously removed the lower door support bracket and failed to replace the lower bracket shim that positions the lower part of the freezer door properly out from the refrigerator cabinet causin
... Read more
g the door gasket seal to bind before the freezer door was fully closed. I removed and replaced this lower door bracket with a new shim made up of serveral thicknesses of cardboard to achieve this spacing and freezer door now closes and seals properly. They had never connected a water supply to the refrigerator although this model is equiped with an ice maker and in door ice and cold water dispenser. The access panel on the back of the unit had been previously removed and discarded. I made up a new access panel from cardboard and connected the water line to the solenoid valve. Valve was so old it would barely open when valve energized and water flow was too slow to make proper sized ice cubes and fill a water glass. I purchased a new water solenoid valve and replaced ther original valve and cured that problem. Replacing the access panel cured an improper cooling problem because with panel removed, most of the air flow bypasses the condenser coils. Lastly I replaced the upper tubular light bulb and the lower light socket I purchased here and installed a 40 watt bulb in the new light socket. Presto! I was able to turn non working abandoned refrigerator into a workable unit.
Read less
Was this helpful?
Thank you for voting!
Leakiong water from the freezer compartment into the lower refrigeration compartment
7 of 12 people
found this instruction helpful.
-
Mark from indianapolis, IN
- Really Easy
- Less than 15 mins
-
Nutdriver
After unplugging the appliance, I unscrewed the screws in the bottom and the back of the freezer compartment and un-clipped the connector for the ice machine, which i do not have installed. I clipped the pink and brown wires and replace the switch with the new switch. unfortunately, the appliance is still dripping water from the freezer c
... Read more
ompartment. It worked for a couple of days then stopped working. Still looking for a true FIX.
Read less
Was this helpful?
Thank you for voting!
Broken drawer
5 of 6 people
found this instruction helpful.
-
Linda from Mabscott, WV
- Really Easy
- Less than 15 mins
I ordered the drawer which arrived 3 days later and I just took out the old one removed the white handle cover placed it on the new drawer and put it back in quick, easy done.
Was this helpful?
Thank you for voting!
Cracked crisper
5 of 6 people
found this instruction helpful.
-
Ronald from Pomona, CA
- Really Easy
- Less than 15 mins
Took out the cracked one, and replace with the new one. Fitted perfectly.
Was this helpful?
Thank you for voting!