- Home
- 1069750323
- Instructions
1069750323 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door light switch disintegrated
2 of 2 people
found this instruction helpful.
-
Thomas from Roseville, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
fridge door switch did not work
2 of 2 people
found this instruction helpful.
-
stu from richmond, VA
- Easy
- Less than 15 mins
-
Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
The handle broke and my wife was afraid to close the door because she might not be able to open it back.
2 of 2 people
found this instruction helpful.
-
Jeff from WINSTON SALEM, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers
The part-select video showed me to do the following:
Unplug dish washer
Open the door and unscrew the screws around the inside of the door all around.
Place the screws in the detergent holder with a cap until finished.
The door mechanism is at the top and attached to two electrical wires.
... Read more
Unfasten the wires from the attachment.
Take the new attachment and fasten the wires to it.
Place the attachment back in the spot and make sure handle is sticking thru the hole to the outside.
Reattach the screws.
Plug back chord.
Finished - 15 minutes
Unplug dish washer
Open the door and unscrew the screws around the inside of the door all around.
Place the screws in the detergent holder with a cap until finished.
The door mechanism is at the top and attached to two electrical wires.
... Read more
Unfasten the wires from the attachment.
Take the new attachment and fasten the wires to it.
Place the attachment back in the spot and make sure handle is sticking thru the hole to the outside.
Reattach the screws.
Plug back chord.
Finished - 15 minutes
Read less
Was this helpful?
Thank you for voting!
After 17 years, the old door gasket was split and showing signs of mold
2 of 2 people
found this instruction helpful.
-
duncan from HOWELL, NJ
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
The gasket has an inner lip that fits over the edge of the door plastic liner. The old gasket was removed by pulling it straight out, in the plane of the door. Try not to pull sideways as it could crack the door liner, which gets brittle with age. The new liner had a brown magnetic strip, which holds the door closed, and this fits behi
... Read more
nd the edge of the door liner. Start on the bottom of the door. A helper is useful to hold the gasket loosely vertical. A flat blade screwdriver can be used to pry away the liner to insert the new seal. Once you have worked in the lower edge, install both sides, and then the top. Some juggling side-to-side may be needed for an exact fit
Read less
Was this helpful?
Thank you for voting!
Drain clogging causing water to leak bottom of fridge
2 of 2 people
found this instruction helpful.
-
Ted C from DSRT HOT SPGS, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver
After watching videos how to replace went very easy.removed ice maker cut wires replaced switch put back together now working ok so far.
Was this helpful?
Thank you for voting!
Faulty light socket
3 of 5 people
found this instruction helpful.
-
Larry from HOUSTON, TX
- Very Easy
- 15 - 30 mins
-
Screw drivers
Followed the video instructions.
Was this helpful?
Thank you for voting!
ice maker gears stripped/ bearing & cup assy broken
3 of 5 people
found this instruction helpful.
-
Timothy from Lake Geneva, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The bearing & cup assembly was broken and the gears in the drive assy were stripped. Unfortunately I couldn't find anywhere to buy the gears without buying the entire motor assy with the gear box already on it. Cost was up to $85 with shipping but at least it now works fine.
To repair: a 1/4 nut driver will take off screw b ... Read more elow ice maker and all you need to do is loosen the 2 screws above the ice maker then push it upward slightly and it will slide off the top 2 screws. Then pull the power connector off from behind the ice maker at the side of the refridge. Then pull straight out and it will slide off the water fill tube. Now with unit out of refridge I took the cover off the front of the ice maker and removed the 3 philip screws. I then pulled the motor/gear assy off from the chassis of the ice maker. I then had to remove the 2 philip screws on the chassis (under the motor/gear assy) to remove the cube maker/element from the chassis. This allowed me to remove the rotating cube spatula bar to replace the filler cup/bearing assy. Then I reinstalled the spatula bar and the 2 philip scews on the chassis to the cube maker/element assy. I then installed the new motor/gear assy to the chassis and installed the 3 remaining philip screws. Put the cover back on the ice maker and inserted assy back into the refridge by first reattaching the power connector and then sliding backward onto the water fill tube and then slipping over the top of the 2 top screws on the refridge. Then I installed the screw below the ice maker and tightened all 3. Presto - repair done in 30 minutes and perfect cubes were spitting out within the hour.
To repair: a 1/4 nut driver will take off screw b ... Read more elow ice maker and all you need to do is loosen the 2 screws above the ice maker then push it upward slightly and it will slide off the top 2 screws. Then pull the power connector off from behind the ice maker at the side of the refridge. Then pull straight out and it will slide off the water fill tube. Now with unit out of refridge I took the cover off the front of the ice maker and removed the 3 philip screws. I then pulled the motor/gear assy off from the chassis of the ice maker. I then had to remove the 2 philip screws on the chassis (under the motor/gear assy) to remove the cube maker/element from the chassis. This allowed me to remove the rotating cube spatula bar to replace the filler cup/bearing assy. Then I reinstalled the spatula bar and the 2 philip scews on the chassis to the cube maker/element assy. I then installed the new motor/gear assy to the chassis and installed the 3 remaining philip screws. Put the cover back on the ice maker and inserted assy back into the refridge by first reattaching the power connector and then sliding backward onto the water fill tube and then slipping over the top of the 2 top screws on the refridge. Then I installed the screw below the ice maker and tightened all 3. Presto - repair done in 30 minutes and perfect cubes were spitting out within the hour.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The coating on the mold /heater unit as cracked and some broken off and cause the water to drip down in the Ice trace and form large icicles
3 of 5 people
found this instruction helpful.
-
James from Tomball, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food.
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim
Was this helpful?
Thank you for voting!
No ice
2 of 2 people
found this instruction helpful.
-
GARY from WEST CHESTER, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I removed the icemaker. One screw at the bottom and then unplug the electric. Remove the old motor from the face that has 3 screws holding it. Put the new motor in. A very simple job. I now have a full ice bin by the next morning.
Was this helpful?
Thank you for voting!
The icemaker on the refrigerator had stoped working.
2 of 2 people
found this instruction helpful.
-
Curtis from Blackwood, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench set
Repair was real easy, I had to remove several screws in the bottom of the icemaker module housing. The unit slide out with no problem there was a wire assembly that hat to be disconnected but this did not present a problem. The old module came out real easy after removing 4 screws and the replacement was not a problem to but in.
Was this helpful?
Thank you for voting!
Ice buildup in freezer causing leaking water into fridge section
2 of 2 people
found this instruction helpful.
-
Diane from Brighton, MI
- Very Easy
- 30 - 60 mins
-
Nutdriver, Pliers
In my case the defrost thermostat was not the problem. Not worth going through the hassle of checking the thermostat as I would have had to cut it out and test it in another freezer (while the food that was in the freezer was being stored elsewhere). I just ended up buying it and replacing it. So, like I said the defrost thermostat was NO
... Read more
T the issue. I ended up getting a drain tube heater strap, and have been keeping my eye on the fridge. It hasn't been long enough to say the strap fixed the problem, but all indications are pointing to that being the case.
Read less
Was this helpful?
Thank you for voting!
Door would pop open. I cleaned gasket made sure nothing in the way of door. Gasket was cracked top and bottom it worked better but the seal was not good.
2 of 2 people
found this instruction helpful.
-
Roy from KAUFMAN, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver
Did just like the video showed took doors off daughter helped take off doors so easy put door on blanket. My daughter 38 went to town putting it on just watch the corners so easy two days after installation the door seals great. You can do this.
Was this helpful?
Thank you for voting!
Defrost drain clogged with ice
2 of 2 people
found this instruction helpful.
-
Michael from CHICAGO, IL
- Easy
- 30 - 60 mins
-
Nutdriver
Replaced gaskets on both doors. Followed the online video link that came with emailed receipt. Worked exactly like demonstrated in the video.
Was this helpful?
Thank you for voting!
Ice maker clicked CW and CCW, but did not make ice
2 of 2 people
found this instruction helpful.
-
Louis from BASKING RIDGE, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Replaced the control of the ice maker assembly.
Was this helpful?
Thank you for voting!
cut old off the door and put new on the door
7 of 17 people
found this instruction helpful.
-
George from Albakurky, NM
- Easy
- 30 - 60 mins
-
Socket set
took door of the refergarator. Then cut old gusket of and clipped the new one on and then put the back. Done!!!!!
Was this helpful?
Thank you for voting!