1069731611 Kenmore Refrigerator - Instructions

All Instructions for the 1069731611
121 - 135 of 582

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice maker stopped making ice
2 of 2 people found this instruction helpful.
  • Sean from Lancster, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.
Was this helpful?
Thank you for voting!
Ice maker failure to produce ice
2 of 2 people found this instruction helpful.
  • Conley from richmond, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
The repair was simple.

I first did a diagnosis of the optical cuircuits and found them good. The tray heated up and when resetting the moor controller, the water cyccled to fill the tray so the only other thing it could be was the motor controller.

removed the service door for the ice maker
I removed the wire protectore screw and shroud
pulled the icemaker unit out and unplugged the unit
removed the motor controller end cap
unscrewed 3 screws holding the motor controller
removed and replaced the motor controller. ensured that all wire harness connector poiints were solid
reverse the above instructions and in 5 hours I was getting ice again!

$90 turned out to be a savings from the $250 it would have cost to have someone come out and look at the fridge.

I highly recommend to anyone who can read and use a screwdriver to perform this repair if you have diagnosed this as the root of your problem!
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 people found this instruction helpful.
  • dorotea from staten island, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
The panel on the freezer door broke
2 of 2 people found this instruction helpful.
  • Carmela from Lincroft,, NJ
  • Really Easy
  • Less than 15 mins
I followed the directions that came with the new part. Thank you for making it so easy. You sent me everything I needed to make the repair.
Was this helpful?
Thank you for voting!
Cimpressor would not start
5 of 11 people found this instruction helpful.
  • Oliver from Madison, AL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Checked compressor with amp meter, and found it was not running, found Overload Switch bad.
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.

BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!
Was this helpful?
Thank you for voting!
My ice maker just stopped working
4 of 8 people found this instruction helpful.
  • Lori from Boca Raton, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I Removed 3 screws, pulled off the plate and put the new one on, screwed in 3 screws and away I went. I could not believe how easy it was to order the part and how quickly it arrived. I was very pleased. And I was literally screaming with excitement when I heard the first set of ice cubes drop!
Was this helpful?
Thank you for voting!
Door light switch disintegrated
2 of 2 people found this instruction helpful.
  • Thomas from Roseville, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
fridge door switch did not work
2 of 2 people found this instruction helpful.
  • stu from richmond, VA
  • Easy
  • Less than 15 mins
  • Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
Broken plastic part at top of water fill tube to freezer
2 of 2 people found this instruction helpful.
  • Jay from Mt. Pleasant, WI
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Simple. 1st, removed broken part to understand part (water fill tube to freezer, plastic part at top of fill tube cracked). 2nd go on your web site and look at prints to find part number, Study video to understand video. 3rd. Called customer service and lady was very nice and efficient. Placed order and received. Study video again a nd installed. My 9 year old grandson was visiting from out of town and assisted in installation. Just over 30 minutes to install
Was this helpful?
Thank you for voting!
Ice maker clicked CW and CCW, but did not make ice
2 of 2 people found this instruction helpful.
  • Louis from BASKING RIDGE, NJ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Replaced the control of the ice maker assembly.
Was this helpful?
Thank you for voting!
Ice buildup in freezer causing leaking water into fridge section
2 of 2 people found this instruction helpful.
  • Diane from Brighton, MI
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
In my case the defrost thermostat was not the problem. Not worth going through the hassle of checking the thermostat as I would have had to cut it out and test it in another freezer (while the food that was in the freezer was being stored elsewhere). I just ended up buying it and replacing it. So, like I said the defrost thermostat was NO T the issue. I ended up getting a drain tube heater strap, and have been keeping my eye on the fridge. It hasn't been long enough to say the strap fixed the problem, but all indications are pointing to that being the case.
Was this helpful?
Thank you for voting!
Removed crisper shelf to clean and it shattered into a million pieces
2 of 3 people found this instruction helpful.
  • Douglas from Naperville, IL
  • Really Easy
  • Less than 15 mins
Ordered the wrong shelf, returned it and ordered the correct shelf. Placed it on the frame. Service was two days.
Was this helpful?
Thank you for voting!
End caps broke on the lower shelf
2 of 3 people found this instruction helpful.
  • Eugene from Erie, PA
  • Really Easy
  • Less than 15 mins
Slid the end caps onto the shelf, placed the tape on the pieces as noted in the directions, and put the shelf back in place. Fast service, exact part, easy to find on the web site! Great!
Was this helpful?
Thank you for voting!
Ice maker: The gear on the motor module was broken
2 of 3 people found this instruction helpful.
  • John from Athens, TN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I had to order the module. It was easy to install. If i could have ordered just the gear and shaft, would have been a lot cheaper. Thanks for the addvise. Bill Paisley
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 people found this instruction helpful.
  • Gail from Golden, CO
  • Really Easy
  • Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
All Instructions for the 1069731611
121 - 135 of 582