- Home
- 1069708771
- Instructions
1069708771 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Filler tube broken and old tube frozen over
4 of 5 people
found this instruction helpful.
-
Alan from Chino, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
this is a snap! 2 screws an a nut to tighten and it works like a charm. the filler tube in my Kenmore refer had broken off in the back. ( really bad location to put this in the beginning) if you push the refer to close to the wall you can break it off easily. remove the water line by loosing the nut and remove the hose from the fill tube
... Read more
( This assumes you have already turned of the water supply or you are standing in a large puddle)remove the 2 screws that hold the filler tube in place. pull out the old filler tube in and slightly upright motion. replace the new fill tube into the same hole and replace the screws. replace the hose and tighten the nut, turn the water back on and check for leaks your done !!
doesn't that feel great?
doesn't that feel great?
Read less
Was this helpful?
Thank you for voting!
Evaporator Fan in Freezer Making Load Noise
4 of 5 people
found this instruction helpful.
-
Ralph from SAINT PAUL, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed freezer shelving. Removed 3 shelving brackets (dovetailed) by sliding them up off of the small square mounted on the freezer wall. This was a stumbling block until
I figured out how to remove these brackets. Removed three Philips head screw in freezer back panel (24) with nut driver. Removed light bulb cover to get some grip ... Read more on back panel. Lifted the back panel up slightly and then folded in down a bit then rotated it to the left. Removed 4 hex head (1/4in) screws on fan shroud (23) and brought down into the freezer. Disconnected electrical spade connectors from motor and removed entire unit from freezer to work on motor. Removed two hex head screws (18) holding motor to the brackets. Pushed new fan on to new motor using a 1/4 nut driver and hammer. Mounted motor to old brackets with two screws (18). Placed motor/fan/shroud unit in freezer and reconnected electrical spade connectors. Replaced motor/fan/shroud in freezer with the 4 hex head screws (15), dropping one behind the coils. Just replaced it with a look alike. Turned power back on to check if the fan was operating normally. Put back panel in place and screwed it in place then put shelving clips back into place and then all the shelving. Appears to operating quietly so far. About 30 minutes to complete the job.
I figured out how to remove these brackets. Removed three Philips head screw in freezer back panel (24) with nut driver. Removed light bulb cover to get some grip ... Read more on back panel. Lifted the back panel up slightly and then folded in down a bit then rotated it to the left. Removed 4 hex head (1/4in) screws on fan shroud (23) and brought down into the freezer. Disconnected electrical spade connectors from motor and removed entire unit from freezer to work on motor. Removed two hex head screws (18) holding motor to the brackets. Pushed new fan on to new motor using a 1/4 nut driver and hammer. Mounted motor to old brackets with two screws (18). Placed motor/fan/shroud unit in freezer and reconnected electrical spade connectors. Replaced motor/fan/shroud in freezer with the 4 hex head screws (15), dropping one behind the coils. Just replaced it with a look alike. Turned power back on to check if the fan was operating normally. Put back panel in place and screwed it in place then put shelving clips back into place and then all the shelving. Appears to operating quietly so far. About 30 minutes to complete the job.
Read less
Was this helpful?
Thank you for voting!
Lights not working some times
4 of 5 people
found this instruction helpful.
-
Harry from COLUMBIA STA, OH
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed old switch and installed new - but did not solve problem
Was this helpful?
Thank you for voting!
nosiy fan operation
4 of 5 people
found this instruction helpful.
-
TOM from GRANVILLE, MA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
most of the time spent on repair was removing the food from freezer compartment other than that removal of a couple screws and disconnecting and reconnecting wires not a huge ordeal
Was this helpful?
Thank you for voting!
Fan motor stopped working.
5 of 8 people
found this instruction helpful.
-
John from Clifton Heights, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I first unplugged the unit.
Secondly I unscrewed the back panel and removed it.
Third, I unplugged the fan, unscrewed it, removed it, and replaced it with the new fan motor.
I then plugged it to confirm that it worked and then put everything back together.
Secondly I unscrewed the back panel and removed it.
Third, I unplugged the fan, unscrewed it, removed it, and replaced it with the new fan motor.
I then plugged it to confirm that it worked and then put everything back together.
Was this helpful?
Thank you for voting!
Ice maker not working
6 of 11 people
found this instruction helpful.
-
Raoul from Thousand Oaks, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
take out Ice maker tray, remove three screws holding the ice maker, unplug electrical connector. Replace with new Ice maker,Ice started to fill the tray. ENJOY!!
THANKS.
THANKS.
Was this helpful?
Thank you for voting!
Ice Maker didn't produce ice cubes.
4 of 5 people
found this instruction helpful.
-
Michael from Long Valley, NJ
- Easy
- 30 - 60 mins
-
Nutdriver
It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of
... Read more
scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.
Read less
Was this helpful?
Thank you for voting!
Broken filler tube at threaded connection
4 of 5 people
found this instruction helpful.
-
Matthew from Phoenix, AZ
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
After discovering that the water noise was coming from the rear of the refridgerator upon pulling it foward I discivered the connection line had broken. So i got a phillips screw driver and removed the the two mounting screws and saw it was one piece. I easliy found the part on PartSelect website and once I got I merely swaped them out
... Read more
and it works good as new!
Read less
Was this helpful?
Thank you for voting!
Fill cup broke.
6 of 12 people
found this instruction helpful.
-
Aliki from Miami, FL
- Really Easy
- Less than 15 mins
Very easy to order from parts select. Took seconds to replace.
Was this helpful?
Thank you for voting!
icemaker was overfolwing with water
5 of 9 people
found this instruction helpful.
-
David from West Bloomfield, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
ordered the part, pulled out the icemaker unit, removed the module, put the new module in, reinstalled the ice maker unit and let it run.
Was this helpful?
Thank you for voting!
Would not make ice any longer
4 of 6 people
found this instruction helpful.
-
James from Concord, MA
- Really Easy
- Less than 15 mins
-
Nutdriver
I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.
Was this helpful?
Thank you for voting!
Replaced broken shelf supports
4 of 6 people
found this instruction helpful.
-
Cheryl from Los Angeles, CA
- Really Easy
- Less than 15 mins
Took out old pieces and popped new ones in, just like that!
Was this helpful?
Thank you for voting!
Shelf End Cap broke
4 of 6 people
found this instruction helpful.
-
Thomas from Danvers, MA
- Really Easy
- Less than 15 mins
This Job is a brease - less than 5 minutes.
Be carelful not to bend metal shelf rail -
Remove broken end cap and slide out metal rail.
You can clean parts before reinstalling.
I recommend slightly squeezing rail before reinstalling to tighten the contact points with plastic end caps.
slide metal rail into en ... Read more d caps (they should snap if contact is right) and secure with sticky tape (sticky tape is supplied with pair of end caps).
Reinstall rail with endcaps attached.
I even have one extra end cap left for another repair if neccessary!
Be carelful not to bend metal shelf rail -
Remove broken end cap and slide out metal rail.
You can clean parts before reinstalling.
I recommend slightly squeezing rail before reinstalling to tighten the contact points with plastic end caps.
slide metal rail into en ... Read more d caps (they should snap if contact is right) and secure with sticky tape (sticky tape is supplied with pair of end caps).
Reinstall rail with endcaps attached.
I even have one extra end cap left for another repair if neccessary!
Read less
Was this helpful?
Thank you for voting!
Fan motor
3 of 3 people
found this instruction helpful.
-
Bonnie from DETROIT LAKES, MN
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Remove bottom of freezer by sliding out the gaskets on each side.
Remove back of freezer. 6 screws.
Remove fan cover. 4 screws.
Remove fan. 3 wires to disconnect. 2 screws to take out.
Install the fan. Connect the 3 wires. Fastened with 2 screws.
Put fan cover back on. 4 screws.
... Read more >Put back of freezer back on. 6 screws.
Put bottom of freezer back in. Slide gaskets in on each side.
Remove back of freezer. 6 screws.
Remove fan cover. 4 screws.
Remove fan. 3 wires to disconnect. 2 screws to take out.
Install the fan. Connect the 3 wires. Fastened with 2 screws.
Put fan cover back on. 4 screws.
... Read more >Put back of freezer back on. 6 screws.
Put bottom of freezer back in. Slide gaskets in on each side.
Read less
Was this helpful?
Thank you for voting!
coating (clear) on ice cube mold peeling off
4 of 6 people
found this instruction helpful.
-
Matthew from Collegeville, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed ice maker from fridge. Removed motor assembly (3) screws on cover, and (2) screws inside. Removed mold (3 screws on bottom) and replaced everything in reverse order. Note: Turned ice maker off for several days while waiting for parts. The water line on this particular model will freeze inside the freezer if ice isn't made for
... Read more
several hours/days. You will have to defrost to begin making ice again.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!