1069650313 Kenmore Refrigerator - Instructions

All Instructions for the 1069650313
121 - 135 of 572

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The handle broke and my wife was afraid to close the door because she might not be able to open it back.
2 of 2 people found this instruction helpful.
  • Jeff from WINSTON SALEM, NC
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
The part-select video showed me to do the following:

Unplug dish washer

Open the door and unscrew the screws around the inside of the door all around.

Place the screws in the detergent holder with a cap until finished.

The door mechanism is at the top and attached to two electrical wires.

Unfasten the wires from the attachment.

Take the new attachment and fasten the wires to it.

Place the attachment back in the spot and make sure handle is sticking thru the hole to the outside.

Reattach the screws.

Plug back chord.

Finished - 15 minutes
Was this helpful?
Thank you for voting!
Ice maker failure to produce ice
2 of 2 people found this instruction helpful.
  • Conley from richmond, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
The repair was simple.

I first did a diagnosis of the optical cuircuits and found them good. The tray heated up and when resetting the moor controller, the water cyccled to fill the tray so the only other thing it could be was the motor controller.

removed the service door for the ice maker
I removed the wire protectore screw and shroud
pulled the icemaker unit out and unplugged the unit
removed the motor controller end cap
unscrewed 3 screws holding the motor controller
removed and replaced the motor controller. ensured that all wire harness connector poiints were solid
reverse the above instructions and in 5 hours I was getting ice again!

$90 turned out to be a savings from the $250 it would have cost to have someone come out and look at the fridge.

I highly recommend to anyone who can read and use a screwdriver to perform this repair if you have diagnosed this as the root of your problem!
Was this helpful?
Thank you for voting!
Broken crisper frame
2 of 2 people found this instruction helpful.
  • ROGER from GREER, SC
  • Really Easy
  • Less than 15 mins
Replaced frame
Was this helpful?
Thank you for voting!
Ice maker stopped making ice
2 of 2 people found this instruction helpful.
  • Sean from Lancster, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.
Was this helpful?
Thank you for voting!
My ice maker just stopped working
4 of 8 people found this instruction helpful.
  • Lori from Boca Raton, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I Removed 3 screws, pulled off the plate and put the new one on, screwed in 3 screws and away I went. I could not believe how easy it was to order the part and how quickly it arrived. I was very pleased. And I was literally screaming with excitement when I heard the first set of ice cubes drop!
Was this helpful?
Thank you for voting!
Door light switch disintegrated
2 of 2 people found this instruction helpful.
  • Thomas from Roseville, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 people found this instruction helpful.
  • dorotea from staten island, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
icemaker wasn't making ice
2 of 2 people found this instruction helpful.
  • JAMIE from HANOVER, PA
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we get many more years out of this icemaker.
Was this helpful?
Thank you for voting!
fridge door switch did not work
2 of 2 people found this instruction helpful.
  • stu from richmond, VA
  • Easy
  • Less than 15 mins
  • Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
The icemaker on the refrigerator had stoped working.
2 of 2 people found this instruction helpful.
  • Curtis from Blackwood, NJ
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench set
Repair was real easy, I had to remove several screws in the bottom of the icemaker module housing. The unit slide out with no problem there was a wire assembly that hat to be disconnected but this did not present a problem. The old module came out real easy after removing 4 screws and the replacement was not a problem to but in.
Was this helpful?
Thank you for voting!
Door would pop open. I cleaned gasket made sure nothing in the way of door. Gasket was cracked top and bottom it worked better but the seal was not good.
2 of 2 people found this instruction helpful.
  • Roy from KAUFMAN, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Did just like the video showed took doors off daughter helped take off doors so easy put door on blanket. My daughter 38 went to town putting it on just watch the corners so easy two days after installation the door seals great. You can do this.
Was this helpful?
Thank you for voting!
Ice maker clicked CW and CCW, but did not make ice
2 of 2 people found this instruction helpful.
  • Louis from BASKING RIDGE, NJ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Replaced the control of the ice maker assembly.
Was this helpful?
Thank you for voting!
cut old off the door and put new on the door
7 of 17 people found this instruction helpful.
  • George from Albakurky, NM
  • Easy
  • 30 - 60 mins
  • Socket set
took door of the refergarator. Then cut old gusket of and clipped the new one on and then put the back. Done!!!!!
Was this helpful?
Thank you for voting!
Defrost drain clogged with ice
2 of 2 people found this instruction helpful.
  • Michael from CHICAGO, IL
  • Easy
  • 30 - 60 mins
  • Nutdriver
Replaced gaskets on both doors. Followed the online video link that came with emailed receipt. Worked exactly like demonstrated in the video.
Was this helpful?
Thank you for voting!
Ice buildup in freezer causing leaking water into fridge section
2 of 2 people found this instruction helpful.
  • Diane from Brighton, MI
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
In my case the defrost thermostat was not the problem. Not worth going through the hassle of checking the thermostat as I would have had to cut it out and test it in another freezer (while the food that was in the freezer was being stored elsewhere). I just ended up buying it and replacing it. So, like I said the defrost thermostat was NO T the issue. I ended up getting a drain tube heater strap, and have been keeping my eye on the fridge. It hasn't been long enough to say the strap fixed the problem, but all indications are pointing to that being the case.
Was this helpful?
Thank you for voting!
All Instructions for the 1069650313
121 - 135 of 572