- Home
- 1069642290
- Instructions
1069642290 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator without an icemaker
-
Fred from Leesburg, FL
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
According to the instruction manual, except for using a saddle clamp and copper tubing. Since I live in a mobile home, the water lines are plastic and I chose to use the same pipe to run the water line. This line was run from under the kitchen sink through the cabinets to the end. From there I used a flexible hose kit sold at the Lowes st
... Read more
ore. I have been buying bags of ice for over 15 years and finally when I bought a bag that had almost the whole side torn, I got angry enough to spend the money for the icemaker. One problem though,the local water isn't that great tasting and the icemaker didn't come with a filter. Upon checking new refrigerators, I find that some of them don't either.
Read less
Was this helpful?
Thank you for voting!
Old ice maker was leaking
-
Dennis from Rochester, MN
- Easy
- More than 2 hours
-
Socket set
Replace ice maker
Was this helpful?
Thank you for voting!
Both light bulbs had been replaced, but lights did not turn on.
-
Richard from Arlington, MA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this helpful?
Thank you for voting!
noisey circulating fan in the freezer
-
Lee from Arvada, CO
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Emptied the freezer. Removed the back panel. (six screws)Removed the fan cover.(4 screws) Unplugged the power. Unplugged three wires from the motor. (hot-neutral-ground)Removed the fan. (2 screws) Installed the new fan and centered for clearance. Reversed the prior instructions.
Was this helpful?
Thank you for voting!
Ice maker not working
-
Michael from Medfield, MA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
Went to various websites looking for guidance. Finally went to PartSelect since I had previously purchased dryer parts. I entered the model info, etc. from my refrigerator and ordered the ice maker installation kit. The install was fairly easy and everything worked perfectly. I am very satisfied I could do the work myself versus calli
... Read more
ng a repair technician.
Read less
Was this helpful?
Thank you for voting!
Added icemaker Kit
-
Ferrell from Breaux Bridge, LA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Followed the very easy instruction that came with kit. Even a partially trained Monkey could do it with the easy instructions. very satisfied. Had Ice in about an Hour.
Was this helpful?
Thank you for voting!
Original Ice Maker of 21 years died.
-
Daniel from Gainesville, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Ordered the complete ice maker kit because I wasn't sure which part went bad. I replaced the ice maker assembly first which was very easy to do. I couldn't tell if the new ice maker was doing anything. I waited almost 16 hours before the ice maker started to run and make ice. I would just say to be patient after installing these parts if
... Read more
you don't immediatly see anything happening. Saving the solenoid and other extra parts if needed in the future.
Read less
Was this helpful?
Thank you for voting!
Would not make ice
-
Roy from Denver, CO
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
It started out being a disappointment. I just moved into a new place that needs many repairs so I didnt want to spend too much time on this one. I ordered this part which arrived in just a few days. Not knowing exactly what was broken I just ordered the whole thing. When I opened the box, the first thing I noticed was that one of the
... Read more
parts of the new ice maker had a big crack in it. Not wanting to go through the hassle of boxing it up and going through the return process, I started taking it apart and replacing the worn or broken owned, (exactly why I ordered the entire unit). Nevertheless, I wanted ice so I fixed it with some of the new ones and some of the old ones. By now I've paid too much for the unit but it was my choice not to send it back and I now have ice. It was pretty easy to fix once I had the parts.
Read less
Was this helpful?
Thank you for voting!
Noisy fan
-
Harry from Cincinnati, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Unplug the refrigerator. Remove the rear shelf supports by lifting them straight up. No tools required. Remove the screws holding the rear cover of the freezer. Use a nut driver to remove the 4 screws holding the fan housing. Unplug the wiring harness, then remove the fan and install the new one. Remount the housing, plug in the har
... Read more
ness replace the rear cover, install the shelf supports and plug in the refrigerator. It was 30 minutes start to finish, which includes the time to gather the tools, unload and reload the freezer, and putting the tolls away!
Read less
Was this helpful?
Thank you for voting!
Switch didn't work
-
Don from Laramie, WY
- Easy
- 15 - 30 mins
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this helpful?
Thank you for voting!
Evaporator motor squeal.
-
Steven from Hilliard, OH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
After finding an almost obsolete part( thanks PartSelect!) the installation was rather easy. Remove the back panel of the freezer and vent with a screwdriver and a nut driver. Disconnect the three wires, green, white and red.Remove motor from mounting and replace with new motor. I had to make a slight adjustment to the ground wire on the
... Read more
new motor that required adjusting the position of the contact-no big deal. The motor fit perfectly. Popped fan on and assembled. 20 minutes max.
Read less
Was this helpful?
Thank you for voting!
Heard a five second buzzing sound repeated 4 or 5 times per cycle coming from rear lower left compressor side.
-
Burton from Pecatonica, IL
- Easy
- 15 - 30 mins
-
Nutdriver
Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.
Was this helpful?
Thank you for voting!
Protective cover for bulb had melted
-
Lee from Brooklyn, NY
- Very Difficult
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent i
... Read more
tems in the fridge from being able to touch. Bad solution.
Read less
Was this helpful?
Thank you for voting!
Broke the arm off the food compartment rocker switch
-
David from St. Pete Beach, FL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips
... Read more
were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Read less
Was this helpful?
Thank you for voting!
no problems at at all
-
Eliseo from Pleasanton, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
removed rear wall panel took off old fan motor disconnected motor. Installed new grommets re-installed motor inserted new fan. Didn't have to trim fan re-connected wires and rear panel and reconnected power. no problems...
Was this helpful?
Thank you for voting!