- Home
- 1069642210
- Instructions
1069642210 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Both light bulbs had been replaced, but lights did not turn on.
-
Richard from Arlington, MA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this helpful?
Thank you for voting!
noisey circulating fan in the freezer
-
Lee from Arvada, CO
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Emptied the freezer. Removed the back panel. (six screws)Removed the fan cover.(4 screws) Unplugged the power. Unplugged three wires from the motor. (hot-neutral-ground)Removed the fan. (2 screws) Installed the new fan and centered for clearance. Reversed the prior instructions.
Was this helpful?
Thank you for voting!
Ice maker not working
-
Michael from Medfield, MA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
Went to various websites looking for guidance. Finally went to PartSelect since I had previously purchased dryer parts. I entered the model info, etc. from my refrigerator and ordered the ice maker installation kit. The install was fairly easy and everything worked perfectly. I am very satisfied I could do the work myself versus calli
... Read more
ng a repair technician.
Read less
Was this helpful?
Thank you for voting!
Added icemaker Kit
-
Ferrell from Breaux Bridge, LA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Followed the very easy instruction that came with kit. Even a partially trained Monkey could do it with the easy instructions. very satisfied. Had Ice in about an Hour.
Was this helpful?
Thank you for voting!
Original Ice Maker of 21 years died.
-
Daniel from Gainesville, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Ordered the complete ice maker kit because I wasn't sure which part went bad. I replaced the ice maker assembly first which was very easy to do. I couldn't tell if the new ice maker was doing anything. I waited almost 16 hours before the ice maker started to run and make ice. I would just say to be patient after installing these parts if
... Read more
you don't immediatly see anything happening. Saving the solenoid and other extra parts if needed in the future.
Read less
Was this helpful?
Thank you for voting!
Switch didn't work
-
Don from Laramie, WY
- Easy
- 15 - 30 mins
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this helpful?
Thank you for voting!
Evaporator motor squeal.
-
Steven from Hilliard, OH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
After finding an almost obsolete part( thanks PartSelect!) the installation was rather easy. Remove the back panel of the freezer and vent with a screwdriver and a nut driver. Disconnect the three wires, green, white and red.Remove motor from mounting and replace with new motor. I had to make a slight adjustment to the ground wire on the
... Read more
new motor that required adjusting the position of the contact-no big deal. The motor fit perfectly. Popped fan on and assembled. 20 minutes max.
Read less
Was this helpful?
Thank you for voting!
Heard a five second buzzing sound repeated 4 or 5 times per cycle coming from rear lower left compressor side.
-
Burton from Pecatonica, IL
- Easy
- 15 - 30 mins
-
Nutdriver
Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.
Was this helpful?
Thank you for voting!
Protective cover for bulb had melted
-
Lee from Brooklyn, NY
- Very Difficult
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent i
... Read more
tems in the fridge from being able to touch. Bad solution.
Read less
Was this helpful?
Thank you for voting!
Broke the arm off the food compartment rocker switch
-
David from St. Pete Beach, FL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips
... Read more
were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Read less
Was this helpful?
Thank you for voting!
no problems at at all
-
Eliseo from Pleasanton, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
removed rear wall panel took off old fan motor disconnected motor. Installed new grommets re-installed motor inserted new fan. Didn't have to trim fan re-connected wires and rear panel and reconnected power. no problems...
Was this helpful?
Thank you for voting!
rReally Noisy Fan
-
Robert from Sierra Vista, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
1. Unplug Refrigerator 2. Remove inside back freezer panel. (4 Screws) 3. Remove Duct Cover (3 Screws). 4. Cut electrical connections to fan. 5. Remove Old Fan motor (2 hex screws. 6. Install ground wire (was not one there previously). 7. Put slide-on electrical connectors on remaining 2 motor wires. (Were not any on original unit.) 8. R
... Read more
eplace Fan Motor (Don't forget the rubber vibration pads) 9. Reconnect electrical wires. 10. Press on plastic fan blade. 11. Plug in refrigerator to test install. It works. 12 Unplug refrigerator and replace ducting and back panel to freezer. Plug it back in. Voila, Quiet again.
Read less
Was this helpful?
Thank you for voting!
The original ice-maker had a defective module and the ice-maker kit cost less than a replacement module
-
Gary from Morganton, NC
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Replaced original ice-maker with the ice-maker from the kit. Operational check was good.
Was this helpful?
Thank you for voting!
leaky ice maker/black flakes in ice
-
Terri L from Coarsegold, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The repair was super easy and the part worked like a charm. I love my new ice maker! I had to take out the top freezer shelf just so I could fit my head in the freezer to find one screw, but otherwise all went fine. Ice maker is held on with two top screws and one bottom screw. Loosen the two top screws, remove the bottom screw and li
... Read more
ft out the ice maker. It plugs into wires on the inside, back of the freezer so this has to be unplugged. Plug in the wires for the new one, slide it down onto the two top, loose screws, tighten those and screw in the bottom one, replace freezer shelves and you are ready for ice...with no huge iceberg fouling up the ice in your ice cube tray. Simple! The wiring thing worried me when others described it, but it's no harder than plugging in a lamp, really. If I can do it, anybody who can stand on a shorty ladder can do it.
Read less
Was this helpful?
Thank you for voting!
Repalce evaporator fan
-
William from Ledyard, CT
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The evaporator fan is located in the freezer behind the back wall. If you have the ice maker remove it first then remove the screws on the top of the panel. You will notice the side brackets for the top shelf will make it hard to remve the panal but by slitly binding the center the panal came right out. The fan is held in a bracke tha co
... Read more
mes right out. The wire unplu right from the fan so do not try to unplg the seal plug to the left side. Swap the fan with the new one useing the new rubber monts re-connect the wires and reasymble. Put the bottom of the back panal in first then work each side in past the shelf bracket binding the center slightly.
Read less
Was this helpful?
Thank you for voting!