- Home
- 1069631651
- Instructions
1069631651 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
A bottle broke the glass bottom shelf.
3 of 4 people
found this instruction helpful.
-
robert from san diego, CA
- Really Easy
- Less than 15 mins
The best part was that it took 2 minutes to order the part on the internet, and the part was delivered in three days. Earlier than expected. it was packaged very well amd I was able to transport it to the refrigerator in our vacation home with out hiring a repairman or additional delay.Thanks.
Was this helpful?
Thank you for voting!
Fan was noisy - bearing had failed
2 of 2 people
found this instruction helpful.
-
Karl from Wellesley, MA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.
Was this helpful?
Thank you for voting!
The icemaker on the refrigerator had stoped working.
2 of 2 people
found this instruction helpful.
-
Curtis from Blackwood, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench set
Repair was real easy, I had to remove several screws in the bottom of the icemaker module housing. The unit slide out with no problem there was a wire assembly that hat to be disconnected but this did not present a problem. The old module came out real easy after removing 4 screws and the replacement was not a problem to but in.
Was this helpful?
Thank you for voting!
Ice maker clicked CW and CCW, but did not make ice
2 of 2 people
found this instruction helpful.
-
Louis from BASKING RIDGE, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Replaced the control of the ice maker assembly.
Was this helpful?
Thank you for voting!
Broken plastic part at top of water fill tube to freezer
2 of 2 people
found this instruction helpful.
-
Jay from Mt. Pleasant, WI
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Simple. 1st, removed broken part to understand part (water fill tube to freezer, plastic part at top of fill tube cracked). 2nd go on your web site and look at prints to find part number, Study video to understand video. 3rd. Called customer service and lady was very nice and efficient. Placed order and received. Study video again a
... Read more
nd installed. My 9 year old grandson was visiting from out of town and assisted in installation. Just over 30 minutes to install
Read less
Was this helpful?
Thank you for voting!
Ice buildup in freezer causing leaking water into fridge section
2 of 2 people
found this instruction helpful.
-
Diane from Brighton, MI
- Very Easy
- 30 - 60 mins
-
Nutdriver, Pliers
In my case the defrost thermostat was not the problem. Not worth going through the hassle of checking the thermostat as I would have had to cut it out and test it in another freezer (while the food that was in the freezer was being stored elsewhere). I just ended up buying it and replacing it. So, like I said the defrost thermostat was NO
... Read more
T the issue. I ended up getting a drain tube heater strap, and have been keeping my eye on the fridge. It hasn't been long enough to say the strap fixed the problem, but all indications are pointing to that being the case.
Read less
Was this helpful?
Thank you for voting!
Cimpressor would not start
5 of 11 people
found this instruction helpful.
-
Oliver from Madison, AL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Checked compressor with amp meter, and found it was not running, found Overload Switch bad.
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.
BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.
BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!
Was this helpful?
Thank you for voting!
My ice maker just stopped working
4 of 8 people
found this instruction helpful.
-
Lori from Boca Raton, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
I Removed 3 screws, pulled off the plate and put the new one on, screwed in 3 screws and away I went. I could not believe how easy it was to order the part and how quickly it arrived. I was very pleased. And I was literally screaming with excitement when I heard the first set of ice cubes drop!
Was this helpful?
Thank you for voting!
Faulty light socket
3 of 5 people
found this instruction helpful.
-
Larry from HOUSTON, TX
- Very Easy
- 15 - 30 mins
-
Screw drivers
Followed the video instructions.
Was this helpful?
Thank you for voting!
The coating on the mold /heater unit as cracked and some broken off and cause the water to drip down in the Ice trace and form large icicles
3 of 5 people
found this instruction helpful.
-
James from Tomball, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food.
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim
Was this helpful?
Thank you for voting!
No ice
2 of 2 people
found this instruction helpful.
-
GARY from WEST CHESTER, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I removed the icemaker. One screw at the bottom and then unplug the electric. Remove the old motor from the face that has 3 screws holding it. Put the new motor in. A very simple job. I now have a full ice bin by the next morning.
Was this helpful?
Thank you for voting!
Drain clogging causing water to leak bottom of fridge
2 of 2 people
found this instruction helpful.
-
Ted C from DSRT HOT SPGS, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver
After watching videos how to replace went very easy.removed ice maker cut wires replaced switch put back together now working ok so far.
Was this helpful?
Thank you for voting!
Door light switch disintegrated
2 of 2 people
found this instruction helpful.
-
Thomas from Roseville, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
Ice maker stopped making ice
2 of 2 people
found this instruction helpful.
-
Sean from Lancster, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here ... Read more for $65.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here ... Read more for $65.
Read less
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 people
found this instruction helpful.
-
dorotea from staten island, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!